X-SENSE HIP-C101W Automatic Cat Litter Box User Manual
- June 13, 2024
- X-SENSE
Table of Contents
X-SENSE HIP-C101W Automatic Cat Litter Box
The picture is for reference only, please refer to the actual product!.
Please read the instruction manual carefully before using product.
Precautions
- This product should be placed and used indoors or similar environment.
- It should be placed on flat ground or wooden ground.
- When transporting the product without package, please do not drag it without leaving the ground and handle it carefully, otherwise the weight sensor will be damaged.
- The cat’s weight should be 2.2LB – 22LB.
- There is a magnet installed on the front of this product. Be patient with pacemakers or related materials should consult their physicians before using this product.
Packing List
- Host ×1
- Power supply adapter ×1
- Special garbage bag (gift) ×1
- Manual ×1
main technical index
product name: fully automatic cat toilet
model:HIP-C101W
power adapter: input AC100-240V/0.4A
output DC12V/1A
rated power:≤6W(without UV lamp sterilization power) UV lamp sterilization
power:≤5W
standby power:≤0.5W
weighing range:1-20kg(MAX)
weighing precision:±0.01kg (static)
cat litter load:≤3L
collecting bucket capacity:≤3L
running noise:≤55dB(A weighting)
UV wavelength: 253.7nm UV lamp working time:15minutes
classification of electrical appliance: II Type equipment
product size: length 655mm x width 642mm x height 605mm
net weight:8.5±0.3kg
normal working environment: environment temperature 5~40°C,Relative
humidity≤93%,no condensation storage and transportation environment:
environment temperature-20~60 ° C,Relative humidity ≤ 93%,no condensation
Instructions
Product sketch
※Preparation before turning on
Before connecting the power supply adapter, make the following preparations (otherwise the weight sensor of the device cannot initialize the data).
- First load the cat litter onto the silicone tray (refer the MAX line).
- Take out the collection bucket, put the garbage bag on it, and put the bucket back in its place.
※Turn on the device
Connect the adaptor to the device (IN DC 12V), the device automatically enters
the standby state. Display interface and function operation.
- Working status: the green indicator light is flashing, indicating that the cleaning cabin is about to rotate; the green indicator light is on steady when the cleaning cabin is rotating.
- Weight display: when the cat is in use, it is displayed as the cat’s weight.
- No bucket reminder: it will be displayed after the collection bucket is taken out. The voice will be broadcast, and the device will stop working.
- STOP: the cleaning cabin will stop when it is rotating, and it will be displayed when device in the induction protection and sterilization mode.
- Bucket full reminder: display when the bucket is full, and the device will stop working.
Usage of APP
- Use your cell phone to search “tuyasmart” in app store or scan the QR code on the product. Then download and setup.
- The device is placed within the effective distance of WIFI, and the device is on standby.
- Switch on cell phone’s WIFI, location, Bluetooth, then open the APP, click “Add Device” on the homepage, then click “Auto Scan”.
- Immediately press the button under the display of device for 5 seconds, until hearing the “ticking” sound, and the WIFI icon flashes.
- Click “Access location” in the “Auto Scan” of the APP, and then click “Start Search”.
- When searched for the “automatic cat litter box” then click “Next”. Enter the WIFI password and click confirm. Click “Done” after connecting and adding successfully
| Function | Description |
|---|---|
| Cat Weight | Real-time feedback of the cat’s weight |
| Toilet times | Number of times cat go to toilet every day |
| One-click cleaning | Press once, the device will run one time for cleaning |
| Smart deodorizing (optional attachment) | null |
| Voice switch | On or off the voice of device |
| Trash can switch | Switch to large or small trash can |
| Timed sleep | Click to enter, you can add timing time. |
| Health management | Figure shows cat’s weight, excretion times, excretion time |
duration
Delayed cleaning settings| Set the time from cat leaving to device cleaning
Cleaning and Maintenance
-
Clean the top cover and surface
Please unplug the power supply adapter, use a clean, soft, damp cloth with some detergent to wipe.
※ Note: There is a circuit board inside the product, and liquids are not allowed to enter. -
Clean the cleaning cabin and collection bucket
The cleaning cabin and the collection bucket are detachable structures, which can be disassembled and washed separately, but they must be dried before put back.
Disassembly steps:
- Unplug the power supply adapter.
- Take out the top cover (refer to the product sketch).
- Remove the fixing band (refer to the product sketch).
- Take out the cleaning cabin.
Common Failures and Troubleshooting Methods
Item| Failure| Cause Analysis|
Troubleshooting
---|---|---|---
1| The weight value has changed|
- Check if the placement is balanced and stable, check if it is placed on a hard floor or wooden floor.
- Check if the cat litter pad is in contact with the device.
- Check if there are other objects in contact with the device.
| Reposition device.
2| Not work|
- Sensor initialization error.
- Malfunction
| Restart the device. If it still does not work, please contact customer service.
※If it still fails after done the above, please call the customer service for consultation.
Note: The company reserves the right to change the technology and appearance of the product. Specifications and information are subject to change without notice.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>