RYOBI ROS300 Cordless Random Orbit Sander Instruction Manual

RYOBI ROS300 Cordless Random Orbit Sander Instruction Manual

Important!
It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.

INTENDED USE

The random orbital sander is intended to be used only by adults who have read and understood the instructions and warnings in this manual, and can be considered responsible for their actions. wood, plastic, or similar materials using the abrasive pads provided. The product should only be used in well ventilated areas. The product is designed for dry sanding only. Do not use for wet sanding. The product is intended for consumer use only. Do not use the product for any other purpose. Use of the product for operations different from intended could result in a hazardous situation.

WARNING
Dust from certain paints, coatings, and other materials may cause irritation or allergic reactions. Dust from wood, such as oak, beech, MDF, and similar materials be allowed to use the product on materials containing asbestos.

WARNING
Do not use compressed air to remove dust from the product. Dirt and grit blown away by compressed air can cause serious eye injury.

WARNING
Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

RANDOM ORBITAL SANDER SAFETY WARNINGS

• Clamp workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage. Do not hold the material you are sanding by hand.
• Do not use sanding paper larger than needed. Extra paper extending beyond the sanding pad can also cause serious lacerations.
• Always wear safety goggles and a dust mask when sanding, especially when sanding overhead.
• A suitable breathing respirator must be worn while sanding lead paint, some woods, and metal to avoid.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise and the operator should pay special attention to avoid the following:

• Injury caused by dust
  • Using the product will produce considerable amount of dust and fine particles. Use the dust collection device or connect a dust extraction vacuum when operating the product. Wear dust masks containing filters appropriate to the materials being worked on. Ensure adequate workplace ventilation. Do not eat, drink, or smoke in the work area. Only operate on materials which are specified in the Intended use section. Do not operate on materials (e.g.,asbestos) which present a health hazard.
• Injury caused by noise and vibration
  • Wear ear protection during the sanding operation. Do not operate the product for long periods of time. See “Risk reduction”.

RISK REDUCTION

It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:

• Keep your body warm in cold weather. When operating the unit wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
• After each period of operation, exercise to increase blood circulation.
• Take frequent work breaks. Limit the amount of exposure per day.

If you experience any of the symptoms of this condition, immediately discontinue use and see your doctor about these symptoms.

WARNING
Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

KNOW YOUR PRODUCT

1. Power cord sleeve
2. Speed control dial
3. Live tool indicator
4. 2QRIIVZLWFK
5. Sander cover
6. Dustbox cover
7. Dustbox container
8. Sanding paper
9. Insulated grasping surface

MAINTENANCE

WARNING
The product should never be connected to a power supply when assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product from the power supply will prevent accidental starting that could cause serious injury.

WARNING
When servicing, use only original manufacturer’s replacement parts, accessories and attachments. Use of any other parts may create a hazard or cause product damage.

WARNING
based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
• Electrical tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure, because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. We do not recommend using the product for extended work on these types of materials.

WARNING
Always wear safety goggles or safety glasses with side shields during power tool operation. If operation is dusty, also wear a dust mask.

• If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
• For greater safety and reliability, all repairs should be performed by an authorised service centre.

LUBRICATION
All of the bearings in the product are lubricated with a the unit under normal operating conditions. Therefore, no further lubrication is required.

ENVIRONMENTAL PROTECTION

 Recycle raw materials instead of disposing of as waste. The machine, accessories, and packaging should be sorted for friendly recycling.

SYMBOLS ON THE PRODUCT

 Safety Alert
V Volts
Hz Hertz
 Alternating current
W Watts
no 1RORDGVSHHG
min-1 Revolutions or reciprocations per minute
 Class II tool, double insulation
 CE Conformity
 EurAsian Conformity Mark
 Ukrainian mark of conformity
 Pad size
 Orbital diameter
 Please read the instructions carefully before starting the product.
 Wear ear protection.
 Wear eye protection.
 Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

SYMBOLS IN THE MANUAL

 Connect to the power supply.
 Disconnect from the power supply.
 Note
 Speed, minimum
 Speed, maximum

The following signal words and meanings are intended to explain the levels of risk associated with this product:

DANGER
Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

WARNING
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

CAUTION
(Without Safety Alert Symbol) Indicates a situation that may result in property damage.

Product Specification

• Random orbital sander
• Model
• Voltage
• No load speed
• Rating
• Orbital stroke rate
• Orbital diameter
• Pad size
• Weight According to EPTAProcedure 01/2014
• Measured sound values determined according to EN 62841:
• A-weighted sound pressure level
• Uncertainty K
• A-weighted sound power level
• Uncertainty K
• Wear ear protectors
• The vibration total values (triaxial vector sum) determined according to EN 62841:
• Vibration emission value
• Uncertainty K
• Replacement part:
• Sanding pad

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.

WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

1. The warranty period is 24 months for consumers and commences on the date the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.
2. There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newly-acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
3. The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
   • any product that has been altered or modified
   • any product where original identification (trade mark, serial number) markings have been defaced, altered or removed – any damage caused by non-observance of the instruction manual
   • any product not displaying the CE approval mark on the rating plate
   • any product that has been attempted to be repaired by a non-authorised warranty service centre or without prior authorisation by Techtronic Industries
   • any product connected to improper power supply (amps, voltage, frequency)
   • any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
   • normal wear and tear spare parts
   • inappropriate use, overloading of the tool
   • use of non-approved accessories or parts
   • Power tool accessories provided with the tool or purchased separately, induding but not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide, etc.
   • Components (parts and accessories) subject to natural wear and tear, including but not limited to service & maintenance kits, carbon brushes, bearings, chuck, SDS drill bit attachment or reception, power cord, auxiliary handle, transport carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact wrench pins & springs, etc.
4. For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
5. A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected
6. This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.

Techtronic Industries GmbH
Max-Eyth-Stralle 10, 71364 Winnenden, Germany
Herewith we declare that the product
Random Orbital Sander
Brand: RYOBI
Model number: ROS300
Serial number range: 44413804000001-44413804999999 is in conformity with the following European Directives and harmonised standards
2006/42/EC, 2014/30/EU, 2011/65/EU EN 55014-1:2017, EN55014-2:2015, EN61000-3-2:2014, EN61000-3-3:2013, EN 62841-1:2015, EN 62841-2-4:2014 RoHS documentation is compiled according to EN 50581:2012

References

• Ryobi Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>