witi 115 Wireless Towing Interface Installation Guide
- June 9, 2024
- witi
Table of Contents
Wireless Towing Interface
Operation & Installation Guide
115 Wireless Towing Interface
Australia’s Most Advanced Anti-Theft System for Caravans and Trailers
Warnings & Safety Instructions
Do not operate WiTi unless you have read and understood this manual and WiTi is installed as per the instructions.
- WiTi Wireless Towing Interface requires WiTi Anti-Theft to be installed in the caravan or trailer
- WiTi automatically pairs when in range but it is always good practice to check the lights before towing to ensure they are all operating.
WiTi Wireless Towing Interface
WiTi replaces the cables connecting a tow vehicle and trailer or caravan with
an advanced Wireless Towing Interface. WiTi transmits all lighting and braking
signals from the tow vehicle to the caravan or trailer wirelessly. WiTi
complies with Australian Design Rules when installed as directed.
WiTi Wireless Towing Interface supports CanBus vehicles and vehicles with
advanced electronics. WiTi supports vehicle specific towing modes and features
for example, disabling reverse sensors when hitched. These features will be
enabled when the WiTi Wireless Towing Interface is in range and paired with
the WiTi Anti Theft unit in the caravan or trailer. Please refer to your
vehicle hand book for vehicle specific towing modes.
WiTi supports all third party electric brake controllers as well as the WiTi
Wireless Electric Brake Controller (sold separately).
Note: Transmission of lighting signals is disabled when the alarm is
activated on the trailer.
Specification
Nominal System Voltage | 12V |
---|---|
Operating Voltage | 9V – 15V |
Operating Current | 38mA |
Standby Current – low power mode | 2mA |
Operating Temperature | -20C – 60C |
FCC ID | 2AC7Z-ESP32 |
Weight | 120g |
Contents
- WiTi Wireless Towing Interface
Installation
The wiring on the 12 pin socket on the tow vehicle must follow Australian wiring guidelines as shown below.
Pin
No. | Circuit | Colour |
---|---|---|
1 | Left-hand turn | Yellow |
2 | Reversing signal | Black |
3 | Earth return | White |
4 | Reght-hand turn | Green |
5 | Service brakes | Blue |
6 | Stop lamps | Red |
7 | Rear lamps, clearance & side marker lamps | Brown |
8 | Battery charger / winch | Orange |
9 | Auxiliaries / Ignition Feed | Pink |
10 | Earth return | White |
11 | Not used | Grey |
12 | Not used | Violet |
Pin 8 must be connected to a permanent power supply from the battery in the
tow vehicle. It does not have to be a high current supply as the WiTi Wireless
Interface will draw very little current.
Pin 9 is optional and can be connected to an ignition source in the tow
vehicle.
This circuit works in conjunction with the ignition output on the Anti-Theft
unit.
When the units are paired and the ignition is on in the tow vehicle then the
ignition output on the Anti-Theft Unit will provide 12V. The best way to
describe this is as a wireless relay. This connection can be used for any
device on the caravan that requires an ignition trigger for example, a DCDC
charger device in the caravan.
This circuit is optional and does not have to be connected if you are not
using the ignition output on the Anti-Theft Unit.
NB. Not all vehicles are wired to Australian Standard VSB1 section 14 please
test Pin 8 is 12V+ and Pin 9 is Ignition 12V+ before installing WiTi.
To operate simply plug the WiTi Wireless Towing Interface into the 12 pin
socket on the tow vehicle.
WiTi Wireless Towing Interface and Communication Module Indicator Lights
There are two LEDs embedded in the WiTi Logo on the Wireless Towing Interface.
When the unit is powered LED 1 (Amber) will illuminate. When the unit is
paired and linked then LED 2 (Red) will illuminate.
Pairing a new WiTi Wireless Towing Interface and Communication Module
Ensure the WiTi Wireless Towing Interface is plugged in and powered on (LED 1
is lit) and in range of each other – within 10 meters.
On the WiTi Wireless Towing Interface unit press and hold the “PAIR” Button.
Whilst still depressing the “PAIR” button, press the RESET Button for half a
second and then let go of the RESET button.
When the RESET button is released, you will notice LED2 flashing rapidly while
LED 1 is still solid. Let go of the PAIR button. The WiTi Wireless Towing
Interface is now in PAIRING mode. The unit will stay in pairing mode for five
minutes while searching for the Anti-Theft System.
Repeat the Pairing Process on the Anti-theft in the Caravan or Trailer.
On successful pairing the WiTi LEDs will flash simultaneously for 5 seconds on
both units to indicate that they have successfully paired with each other.
Once the LED’s stop flashing both units will exit PAIRING Mode and return to
normal operation. Both LED1 and LED2 will now be illuminated when they are in
range and powered.
If either unit did not detect a PAIRING partner during the pairing sequence,
then LED 1 and LED 2 will flash in an alternating sequence for 5 seconds
(LED1-LED2-LED1- LED2) this indicates that pairing has failed and the unit
will then return to normal operation mode with just LED 1 illuminated. Repeat
the pairing process.
Operation Guide
WiTi Wireless Towing Interface replaces the traditional cables between a tow
vehicle and caravan / trailer with an advanced wireless connection. WiTi
transmits all lighting and braking signals using the latest WiFi technologies
for fast, secure and stable communication. Although wireless, WiTi is not
dependant upon the Internet and
communication is point to point between the vehicle unit and trailer unit. The
signal is also encrypted for security and other wireless devices will not
interfere with the WiTi
Wireless Towing Interface (mobile phones, bluetooth, wifi devices, etc.)
No more cables to damage or rip out, no more corroded terminals and no more
loose connections.
Low Power Mode
WiTi Wireless Towing Interface will enter low power mode if there is
inactivity for 24 hours. In this mode power draw is less than 2 milliAmps.
WiTi will exit Low Power Mode when it detects an input from the driving light
circuit.
Limited Warranty
If Leisure Technologies determines that you are covered by a warranty as set
in the Australian consumer law the company shall at its expense: (a) repair
the product or replace the product with a new unit (which may have used
refurbished parts of similar quality); (b) ship the repaired or replaced unit
back to you; (c) warrant the repaired or replaced product for a reasonable
period; and/or (d) refund money paid for the product. The Company has the
discretion as to which remedy applies.
Warranty period
The warranty period starts on the date of purchase and ends 24 months later.
For the purpose of this limited warranty, the date of purchase is the date
indicated on the original bill of sale or receipted invoice for the product
from the vendor from which you acquired this product.
How to get warranty service
During the warranty period, if you wish to return a defective product you may
contact us via www.witi.com.au. You may then return
the defective product to the address given accompanied by an acceptable proof
of purchase (a bill of sale or receipted invoice).
What is not covered
The limited warranty does not cover a product:
- for which you are not the original purchaser;
- that is damaged by using in a way that was unreasonable or unintended;
- that is returned after the applicable warranty period set out above has expired;
- that has been installed other than per the product installation guidelines;
- that has been maintained, altered or modified, opened or repaired, other than by the company or by a company authorised service centre;
- that has been physically damaged, other than by the company or a company authorised service centre.
- To the extent permitted by law, Leisure Technologies, its directors, officers, employees, suppliers and agents, shall not be liable for injury to persons or property, or for any indirect, special, incidental or consequential, punitive or exemplary damages and liability and shall be limited to the amount you paid for the product.
Disclaimer
-
WiTi products are designed for installation by reasonably competent consumers.
Consumers are taken to have sufficient knowledge of the intended caravan or trailer unit and its appropriateness for the installation of any WiTi products. -
Installation of WiTi products may require consumers to have knowledge and experience using powered tools and electrical wiring. Consumers without such knowledge are to refrain from attempting any installation of WiTi products and to consult their nearest WiTi specialist or qualified Auto Electrician.
-
Prior to the installation of any WiTi product consumers are taken to have comprehensively read and understood the appropriate WiTi operation and installation guide included with the product.
-
It is the consumer’s sole responsibility to have WiTi products properly installed on their vehicle and/or trailer units along with any modifications necessary for the proper
installation of WiTi products. -
Consumers are solely and completely responsible for evaluating their trailer units to ensure that the trailer units, and each part thereof, is appropriate, adapted and applicable for installation and use of WiTi products.
-
Any and all WiTi unit damages caused by a consumer’s failure to modify the caravan or trailer properly for installation and use of one or more WiTi products not covered by this disclaimer is the sole responsibility of the consumer.
-
Leisure Technologies Pty Ltd and their distributors and resellers also expressly disclaims all liability for direct, indirect, special, incidental, or consequential damages, including but not limited to, damage or loss of property or equipment, injury to person whether physical or not, loss of profits or revenue, cost of purchase or replacement of goods, or claims of customers of the purchaser that result from the incorrect installation of any WiTi Anti-Theft unit or subunit.
Other important notices
To the extent permitted by law, this limited warranty constitutes the entire
agreement on the subject matter and supersedes any prior agreement or
understanding, written or oral. Where used herein, the company shall mean
Leisure Technologies Pty Ltd and its subsidiaries and associates.
Our goods come with guarantees that cannot be excluded under the Australian
consumer law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major
failure. The benefits under your warranty are in addition to other rights and
remedies under the law in relation to the product.
Scan to discover morehttp://www.witi.com.au