MiBOXER E2-RF 2 in 1 LED Controller Instruction Manual
- June 16, 2024
- MiBOXER
Table of Contents
MiBOXER E2-RF 2 in 1 LED Controller
Product Information
Specifications
- Product Name: Subordinate New Brand 2 in 1 LED Controller (2.4G)
- Wireless Technology: 2.4GHz
- Features: Low power consumption, long signal transmission, strong anti-interference
- Auto-transmitting function
- Compatible with remote controls (purchased separately)
- Color temperature adjustable
- Dim brightness
- Remote control distance: 30m
- Support Smartphone app control (2.4GHz gateway is needed)
- Support third-party voice control (2.4GHz gateway is needed)
Set up Output Mode
To set up the correct output mode based on the feature of lights:
- Press the SET button continuously to switch output mode (Note: It will log out without operation within 3 seconds)
- Confirm the output mode based on the color of the indicator:
| Indicator color | Output |
|---|---|
| Red Light | Single Color Mode |
| Green Light | Dual White Mode |
PUSH Dimming
To adjust brightness using PUSH dimming:
- Short press PUSH switch: Turn ON/OFF light
- Long press PUSH switch: Stepless dimming brightness. Long press and release your finger, then repeat long pressing to increase or decrease brightness.
Compatible with 2.4G RF Remote Controls
The product is compatible with the following 2.4G RF remote controls (purchased separately):
- FUT006
- FUT007
- B1 / B1-B / T1
- B2 / T2
- K1 / K1-B
- FUT087 / FUT087-B
- S1-B / S1-W / S1-G
- WL-Box1
G RF Remote Control Instructions
Linking Code Instructions
-
1. Press the Power or SET or PUSH button once. - Power off for 10 seconds and power on again, or short press the SET button once, or turn on the light via the PUSH switch.
- If the lights blink slowly for 3 times, it means linking is done successfully.
Note: If the light is not blinking slowly,
please follow the above steps again. Lights that have already been
linked cannot be linked again.
Unlinking Code Instructions
-
1. Press the Power or SET or PUSH button once. - Power off for 10 seconds and power on again, or short press the SET button once, or turn on the light via the PUSH switch.
- Short press the Power button 5 times within 3 seconds.
- If the lights blink quickly for 10 times, it means unlinking is
done successfully.
Note: If the light is not blinking quickly, please follow the above steps again. Lights that haven’t been linked do not need to be unlinked.
FAQ
Q: What is the wireless technology used in this product?
A: This product uses 2.4GHz wireless technology.
Q: What is the remote control distance?
A: The remote control distance is 30m.
Q: Can I control the product using a Smartphone app?
A: Yes, you can control the product using a Smartphone app, but you will need a 2.4GHz gateway.
Q: Is the product compatible with third-party voice control?
A: Yes, the product is compatible with third-party voice control, but you will need a 2.4GHz gateway.
2 in 1 LED Controller ( 2.4G ) Instruc?on Manual
Product Features
Product adopt the widely used 2.4GHz wireless technology with the features of low power consumption, long signal transmitting and strong anti-interference, etc. Product has auto-transmitting function. Widely used on the controlling of hotel lighting and home lighting.
Set up output mode
Set up correct output mode based on the feature of lights Setting method: Press “SET” button continuously to switch output mode (attention: it will log out without operation within 3 seconds)
Output mode sheet ( confirm output mode based on color of indicator)
| Indicator color | Red Light | Green Light |
|---|---|---|
| Output | Single Color Mode | Dual White Mode |
PUSH Dimming
Short press PUSH switch:
Turn ON/OFF light
Stepless dimming brightness.
Long press PUSH switch:
Long press and release your finger, then repeat long pressing to increase or
decrease brightness.
Compatible with these 2.4G RF remote controls (Purchased separately)
2.4G RF Remote control instruction
Linking Code Instructions
Power off 10 seconds and Short press the” ” button 3 times within 3 seconds.
power on again or short press “SET” one time or turn on light via PUSH switch
Lights blink 3 times slowly means linking is done successfully.
Linking failed if light is not blinking slowly, Please follow above steps
again.
(Note: Light that have linked can’t link again)
Unlinking Code Instructions
- Power off 10 seconds and power on again or short press “SET” one time or turn on light via PUSH switch
- Short press ” | ” button 5 times within 3 seconds.
- Lights blink 10 times quickly means unblinking is done successfully.
Unlinking failed if light is not blinking quickly, Please follow above steps
again.
(Note: Light haven’t linked that don’t need to unlink)
Auto transmitting (2.4G RF remote signal)
The light can transmit remote signal to another light automatically while the
distance between lights are 30m, the remote control distance is unlimited.
(Attention: all lights must be linked with same remote)
PWM high frequency / low-frequency switching (only for remote control) Switch to high frequency (16KHz):
Press “OFF” button 1 time within three seconds and press “ON” button 5 times,
Activated successfully once led light flashes 2 times quickly.
Switch to low frequency (250Hz):
Press “ON” button 1 time within three seconds and press “OFF” button 5 times,
Activated successfully once led light flashes 2 times slowly.
“Do Not Disturb” mode is activated and shut down (default activated)
Turn on “Do Not Disturb” mode (wide using in the area which have power failure
frequently to save energy)
2.4G RF Remote turn on and turn off instruction Turn on “Do Not Disturb”
mode:
Press “OFF” button three times within three seconds and press “ON” button
three times, Activated successfully once led light flashes four times quickly.
Attention: Do not disturb mode is activated
-
When the light is OFF status (For example: Use app or remote to turn off light)
The light is OFF status once you turn off power and turn on again.
(User must turn off and turn on power twice times to activate light or use APP / remote to activate light) -
When the light is ON status
The light is ON status once you turn off and turn on power one time.
Turn off “Do Not Disturb” mode:
Press “ON” button three times within three seconds and press “OFF”
button three times, closed successfully once led light flashes four times slowly.
Attention: The light will be always “ON” status if you turn on and turn off power once user closed “Do Not Disturb” mode.
Attention
- Please turn off power supply before installation.
- Please ensure input voltage to be same as requirements from device.
- Don’t disassemble device if you are not expert, otherwise it will damage it.
- Please do not use the light in the place with widely range metal area or strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected.
Scan QR code to watch 2.4GHz series video instruction Or enter into following link directly https://miboxer.com/light/video/1pc_remote.html
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>