cell2 FX6 Flexion 6+6 LED Dual Colour Light Head User Manual
- June 16, 2024
- Cell2
Table of Contents
FX6 Flexion 6+6 LED Dual Colour Light Head User Manual
6+6 LED DUAL COLOUR LIGHTHEAD
Wiring
To Chassis Ground: BLACK
To+VDC for Warning Mode 1 (fuse @ 1A): RED
Default Colour Mode – Colour 1
To+VDC for Warning Mode 2 (fuse @ 1A): WHITE
Default Colour Mode – Colour 2 117.4mm (4.62″ )
To+VDC for Warning Mode 3 (fuse @ 1A): GREEN
Default Colour Mode – Colour 1 alt. 2
NOTE: Order of Precedence: Mode3 > Mode2 > Mode1
For Synchronization and Flash Pattern: YELLOW
Connect YELLOW wire of all lightheads together for synchronization. (All lightheads should be set to the same Flash Pattern)
Operation
For Flash Pattern Selection:
Each Warning Mode may select and save one Flash Pattern. While activating a Warning Mode, momentarily apply YELLOW wire to +VDC :
- Once to the next pattern.
- Quick three times to FP#1 (refer to Flash Pattern Chart)
Shortcut Setting for Steady EF (External flasher):
This shortcut allows quick changing of trigger wires setting to each color with Steady EF pattern all at one time. Momentarily apply YELLOW wire to +VDC for 3~4 seconds (visual feedback: ON→OFF→ ON) while activating any warning mode. Colour mode and Flash Pattern of each warning mode will be set to:
- Warning Mode 1 = Colour 1, FP#6 Steady EF
- Warning Mode 2 = Colour 2, FP#6 Steady EF
- Warning Mode 3 = Same Colour mode, FP#21 OFF
Setting Mode
The following settings will require user to enter SETTING MODE to operate ; to enter:
- Power off the unit completely and power up by applying +VDC to RED (or or GREEN) and YELLOW wires simultaneously.
- Remove YELLOW wire from +VDC to enter SETTING MODE. Lighthead will then flash in low-power while in SETTING MODE.
- To save and exit the setting, simply disconnect the power after operation.
For Simultaneous or Alternating Synchronization:
To change Group, while in setting mode, momentarily apply YELLOW wire to +VDC for 3~4 seconds. the lighthead will display short flashes:
Simultaneously Alternately
NOTE:
- Lightheads of the same Group will flash together.
- Lightheads of the Group 1 & Group 5 will flash alternately.
For Color Mode Setting:
- Each Warning Memory may select and save one Colour Mode. While in SETTING MODE ; the lighthead will display its current Colour Mode:
- Single Colour flashing Color 1 = Colour 1
- Single Colour flashing Color 2 = Colour 2
- Dual Colour flashing Color 1 = Colour 1 alt. 2
- Dual Colour flashing Color 2 = Colour 2 alt. 1
- Momentarily apply YELLOW wire to +VDC for less than 3 seconds to change Colour Mode.
- Save and exit SETTING MODE by disconnecting all power.
Reset to Factory Default Settings:
This product can be configured ideally by using BlinkCast Programmer with desired Flash Pattern, Group (Phase), and Colour Mode to save your installation time! Contact your sales representatives or see your User Manual of BlinkCast Programmer for detailed information.
Installation
Curved Surface / Flat Surface
1. [Curved Surface] Use curvature template to check surface mountability: make sure surface curvature is over 120 degree.
2. Mark and drill a wire passage hole on the mounting surface. Make sure no vehicle parts could be damaged by the drilling process. (Thoroughly deburr hole and use grommet for wire passage hole if needed)
3. Clean and dry the mounting surface with alcohol prep pad provided. (or 50:50 mix of isopropyl alcohol and water)
4. Remove the tape liner from the tape and apply the lighthead to the surface and press it firmly for 30 seconds. Full adhesion and bonding will be achieved after 72 hours at room temperature.
5. [Flat Surface] For best secure installation, it is recommended to always mount lightheads with screws.
[Curved Surface] Due to lighthead tension, it is required to always mount lightheads with screws on curved surface.
6. Once secured, apply screw covers onto the lighthead for best aesthetic. (use silicon glue to better scure the screw cover)
Prohibition
Mounting Dimensions
Curvature Template
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>