Valeo 088899 Premium Fogstar Right Side Fog Light User Manual

June 13, 2024
Valeo

Valeo 088899 Premium Fogstar Right Side Fog Light User Manual

How To Install Fog Lights

Installing Wiring For Your New Fog Lights\

Locate Your Vehicle’s Pass Through Hole In The Firewall Designed For Wires To Run Through

If you’re adding fog lights to a vehicle not originally equipped with them, you’ll need to start by running the wiring for an on-off switch from under the hood to the inside of the vehicle. The easiest and most direct way to do so is to run the wire through the vehicle’s firewall. Most vehicles will already have such a hole drilled on the driver’s side as a pass-through for other cables, so locate this hole. In the unlikely chance your vehicle doesn’t already have a pass-through hole under or behind the dash, you’ll need to drill one and install a tight rubber grommet around the wire to seal out the elements.

Connect Your Fog Light Switch

Next, take the black ground wire included for the switch and connect one end to the grounding terminal on the back of the switch. Connect the other one to an unpainted metal section under the dash – you may need to drill in order to create a hole if a suitable one can’t be found. A wire with a fuse connected to it should be included also – these are often red in color. Hook this into the corresponding terminal on the back of the switch, then run the other end out through the firewall hole back into the hood area. The red wire will have a  connector piece designed to snap in place with another section of red wire that connects to the relay, then the battery. Connect this last.

Synch Power For The Fog Lights To Your Ignition

Your kit may come with a wire (usually green in color) that’s designed to be connected to the ignition fuse inside the fuse box – ensuring the fog lights will only operate when the vehicle’s ignition is in the ‘on’ position. If your fuse box is inside the vehicle, run this wire through the firewall hole. If the fuse box is under the hood, connect it there – the fuse panel cover and your owner’s manual should direct you the applicable fuse.
Finally, snap the connectors on each section of the red wire together to bring power to the entire setup. You’ll see black ground wire extensions that came in the kit. Connect them to the matching black ground wires running out of the back of the fog lights, then connect them to an unpainted section of the vehicle frame. Connect (white) power wires together with the matching (white) power wires from each light. After that, connect them to the Y-shaped (white) power wire that’s had the other end of it run inside the vehicle.  Performing some of the above wiring work may require the use of common electric wiring and cable tools.

Removing A Bumper Cover To Install Fog Lights

If your vehicle was not equipped with fog lights from the factory, there’s a good chance the bumper cover already has openings for them or pre-defined cutout areas marked on the inside. Vehicles that have nothing at all will require measuring and cutting by eye. In order to remove the front bumper cover for any of these jobs, look for bolts and screws that secure it in place. On some vehicles, you’ll see attachment points after opening the hood where the top of the bumper cover meets the cowl panel. You’ll definitely find securing points underneath the vehicle where the bumper cover meets splash shields and close to the edge of wheel well openings where the bumper cover meets the wheel well liner. If there are flat plastic caps or clips, remove them with a small flathead screwdriver by wedging them up.

Remove the bolts with an applicable socket wrench or flat wrench. In the event your vehicle manufacturer has used rivets to secure things, they’ll need to be drilled out with a traditional drill. Then you’ll need a rivet gun to reinstall new ones – not an expensive purchase, but the proper tool to ensure parts stay safely on. Once all fasteners are removed, the bumper cover can be detached. Many are designed to slide horizontally along special bracket pieces mounted underneath before coming completely loose, so move the bumper cover in this fashion first if you aren’t able to obtain specific instructions on your make and model.

Cutting Holes In Your Bumper Cover To Mount New Fog Lights
If you don’t already own a cutting tool, a kit that includes small cutting wheels and all other bits needed to drill, grind, sharpen, and polish to perfection will be invaluable at this point – get one. Once your front bumper cover has been removed from the vehicle, use your fog light as a stencil to draw a line around where you’ll be cutting – it’s okay to make the hole slightly bigger than the fog light because your add-on kit will come with plastic bezel pieces that mount on the outside of the bumper cover. The bezels will hide any gaps.

Be Careful! When cut along the lines, then see how the lights and the bezel pieces fit. Install your mounting brackets to the bumper cover with the hardware included in the kit, then connect the wiring as discussed earlier in the article.

Mounting Universal Fog Light Brackets Directly To A Metal Section Of Your Vehicle
A fog light kit will include universal mounting brackets designed to bolt onto the bumper of your vehicle, to the framework underneath the bumper, or on a cross member just behind the grille. It’s pretty much your choice where you wish to put them.

If you’ve got a grille guard or bull bar mounted on your vehicle already, you’ll typically find pre-existing holes along tubular bar sections put there solely for the purpose of mounting lights and other accessories. When drilling into metal is required, it’s important to use drill bits rated for metal because they can handle greater levels of heat buildup. Use the size of the drill bit specified by the instructions in the kit because you’ll want a hole big enough to slide the bracket bolt through, but not so big that that the corresponding nut and washer are loose and wobble. Next, secure the fog light mounting bracket on the vehicle and tighten all nuts in place firmly. Mount the fog light onto the bracket, then connect the wiring to the lights as discussed in the wiring section of this article.

Download PDF:Valeo 088899 Premium Fogstar Right Side Fog Light User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals