K RCHER SC 5 EU Cleaning Equipment And Pressure Washers Instruction Manual

K RCHER SC 5 EU Cleaning Equipment And Pressure Washers

Specifications

• Model: SC 5 Deluxe
• Voltage: 220-240V
• Phase 1
• Frequency: 50Hz
• Heating Power: 2250W
• Maximum Operating Pressure: 0.4MPa
• Heating Time: 3 minutes
• Continuous Steam Output: 60g/min
• VapoHydro Function: 150g/min
• Water Tank Capacity: 1.3 liters
• Weight: 5.6kg
• Dimensions: 400mm x 270mm x 300mm

Product Usage Instructions

General Notes
Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Keep both books for future reference or for future owners.

Intended Use
The SC 5 Deluxe is designed for use in private households. It is intended for cleaning with steam and can be used with appropriate accessories as described in these operating instructions. Detergents are not required.

Environmental Protection
Please refer to www.kaercher.de/REACH for current information on ingredients and environmental protection measures related to this product.

Accessories and Spare Parts
The scope of delivery may vary depending on the model. Please refer to the packaging for details. See graphic page for illustrations.

Safety Features
This product is equipped with the following safety features:

• Pressure Regulator
• Safety Thermostat
• Boiler Thermostat
• Maintenance Closure

Assembly
Follow the instructions below to assemble the product:

1. Pull the water tank vertically upwards (see Figure A).

Operation
Follow the instructions below to operate the product:

1. Plug in the power cord to a power outlet.
2. Use the digital display and LED lights to set the desired steam level.
3. Adjust the steam quantity using the control knob.
4. Use the VapoHydro function for maximum steam output.

Important Application Instructions
Follow the instructions below for specific applications:

Auffrischen von Textilien (Refreshing Textiles)

• Hold the steam gun at a distance of approximately 30cm from the textile surface.
• Move the steam gun slowly over the textile surface to refresh it (see Figure H).

Glass cleaning (Glass Cleaning)

1. Attach the small round brush to the steam gun (see Figure G).
2. Hold the steam gun at a distance of approximately 20cm from the glass surface.
3. Move the steam gun slowly over the glass surface to clean it (see Figure H).

Bodentuch abnehmen (Removing Floor Cloth)

1. Switch off the steam cleaner and unplug it from the power outlet.
2. Allow the steam cleaner to cool down.
3. Remove the floor cloth carefully (see Figure L).

Teppichgleiter (Carpet Glider)

1. Attach the carpet glider to the floor nozzle (see Figure H).

2. Start cleaning the carpet using the steam cleaner (see Figure L).

Recommended Steam Levels

Pflege und Wartung (Care and Maintenance)
Follow the instructions below for care and maintenance:

Dampfkessel entkalken (Descaling the Boiler)

1. Switch off the steam cleaner and unplug it from the power outlet.
2. Allow the steam cleaner to cool down.
3. Open the maintenance closure.
4. Drain the water from the boiler.
5. Mix the descaling agent with water and pour it into the boiler.
6. Close the maintenance closure.
7. Shake the steam cleaner gently to distribute the descaling agent.
8. Plug in the power cord and switch on the steam cleaner.
9. Allow the descaling agent to work for the recommended time.
10. Drain the descaling agent from the boiler.
11. Repeat the descaling process if necessary.
12. Rinse the boiler with cold water 2 or 3 times.

FAQ

• Q: Can I use detergents with the SC 5 Deluxe?
  A: No, detergents are not required for cleaning with this steam cleaner.

• Q: What is the maximum operating pressure of the SC 5 Deluxe?
  A: The maximum operating pressure is 0.4MPa.

General notes

Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly. Keep both books for future reference or for future owners.

Intended use
Only use the appliance in private households. The appliance is intended for cleaning with steam and can be used with appropriate accessories as described in these operating instructions. Detergents are not required. Observe the safety instructions.

Environmental protection
The packing materials can be recycled. Please dispose of packaging by the environmental regulations. Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with household rubbish.
Notes on the content materials (REACH)
Current information on content materials can be found at: www.kaercher.de/REACH

Accessories and spare parts
Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely. Information on accessories and spare parts can be found at www.kaercher.com.
Scope of delivery
The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

Warranty

The warranty conditions issued by our sales company apply in all countries. We shall remedy possible malfunctions on your device within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorized customer service site. (See overleaf for the address)

Safety devices

CAUTION
Missing or modified safety devices Safety devices are provided for your own protection. Never modify or bypass safety devices.

Symbols on the device
(according to the type of appliance)

Pressure controller
The pressure controller keeps the pressure in the steam boiler as constant as possible during operation. The heating is switched off when the maximum operating pressure is reached in the steam boiler and is activated if there is a pressure drop in the steam boiler as a result of steam removal.

Safety thermostat
The safety thermostat prevents the device from overheating. If the pressure regulator and the boiler thermostat fail and the unit overheats, the safety thermostat switches the unit off. Before resetting the safety thermostat, contact the responsible KÄRCHER Customer Service.

Boiler thermostat
The boiler thermostat switches off the heating in the event of a fault; for example, if there is no water in the steam boiler and the temperature in the steam boiler rises. As soon as you refill the water, the device is ready for use again.

Maintenance lock
The maintenance lock seals the steam boiler from the steam pressure present. The maintenance cap is also a pressure relief valve. If the pressure regulator is defective and the steam pressure in the steam boiler rises, the pressure relief valve opens and steam is escapes through the lock. Before restarting the device, contact the responsible KÄRCHER Customer Service.

Description of the device

The maximum amount of equipment is described in these operating instructions. Depending on the model used, there are differences in the scope of delivery (see packaging).
For the illustrations, refer to the graphics page. Illustration A

1. Device socket
2. LED lights
3. Selector switch
4. Carrying handle
5. Temperature display
6. Accessory storage area
7. Water reservoir
8. Main connection cable with main plug
9. Display – OFF position
10. Min. steam stage
11. Med. steam stage
12. Max. steam stage
13. VapoHydro function steam stage
14. Maintenance lock
15. Park bracket for floor nozzle
16. Steering roller
17. Steam gun
18. Steam lever
19. Unlocking button
20. Child lock
21. Steam hose
22. Steam connector
23. Spotlight nozzle
24. Round brush (small)
25. Round brush (large)
26. Power nozzle
27. Crevice brush
28. Manual nozzle
29. Manual nozzle cover
30. Extension tubes (2 x)
31. Unlocking button
32. Floor nozzle
33. Hook and loop fastener
34. ** Floor cloth (1x)
35. Floor cloth (2x)
36. Carpet glider
37. Descaler
38. ** Steam pressure iron
39. ** Indicator light (orange)-heating
40. ** Steam switch (bottom)
41. Steam connector
    Accessories can be bought as an optional item

Installation

Installing accessories

1. Open the cover on the device socket. Illustration B
2. Connect the steam connector to the device socket so that the steam connector audibly engages. Illustration B
3. Push the open end of the accessory onto the steam gun so that the unlocking button on the steam gun engages. Illustration G
4. Push the open end of the accessory onto the spotlight nozzle. Illustration H
5. Connect the extension tubes with the steam gun.
   • a. Push the 1st extension tube onto the steam gun so that the unlocking button on the steam gun engages. The connection pipe is connected.
   • b. Push the 2nd extension tube onto the 1st extension tube. The connection pipes are connected. Illustration I
6. Push the accessory and / or the floor nozzle onto the free end of the extension tube. Illustration J The accessory is connected.

Disconnecting accessories

1. Move the child lock back. The steam lever is locked.
2. Push the cover on the device socket down and disconnect the steam connector from the device socket.
3. Press the unlocking button and pull the parts apart. Illustration O

Operation

Filling water
The water reservoir can be removed at any time for filling or be filled directly at the device.
ATTENTION Damage to the device

• Unsuitable water can block the nozzles or damage the water level indicator.
• Do not fill in pure distilled water. Use a maximum of 50% distilled water mixed with tap water.
• Do not use condensation from the clothes dryer for filling.
• Do not use collected rain water for filling.
• Do not use cleaning agents or other additives (e.g. scents) for filling.

Removing the water reservoir for filling

1. Pull the water reservoir vertically upwards. Illustration C
2. Fill the water tank vertically with tap water or a mixture of tap water and no more than 50% distilled water.
3. Insert the water reservoir and press downwards until it locks into place.

Filling the water reservoir directly on the device

1. Fill tap water or a mixture of tap water and no more than 50% distilled water from a vessel into the filling hole of the water reservoir up to the “MAX” mark. Illustration D

Switching on the device

Note If there is no or too little water in the steam boiler, the water pump starts to run and pumps water from the water reservoir into the steam boiler. The filling process can take several minutes.
Note The device briefly closes the valve every 60 seconds causing an audible soft click. Closing prevents the valve from clogging. This does not affect the steam output.

1. Place the device on a firm surface.
2. Insert the main plug into a socket.
3. Turn the selector switch from the OFF position to the steam setting selection range. Illustration E
   Explanation for display status:

• The system operating temperature refers to the actual temperature of the boiler. Since the boiler is a sealed system. the higher the temperature, the higher the steam pressure. At 4,0 bar of steam pressure, the maximum temperature inside the boiler is 150 °C degrees. 4. The temperature display is up to 140 °C and the LED light lights up a continuous green after approx. 3 minutes.The device is ready for use. Illustration F 5. Press the steam lever. Illustration G Steam leaks out.

Regulating the steam volume
The expelled steam volume is regulated using the selector switch for steam volume. The selector switch has the setting options min. steam stage for light soiling to max. steam stage for heavy soiling. The VapoHydro function is for the removal of heavy soiling in areas that are difficult to access.

1. Set the selector switch for the steam volume to required steam volume.
2. Press the steam lever.
3. Before starting cleaning, point the steam gun at a cloth until steam is expelled evenly.

Refilling water
If there is not enough water in water reservoir, the LED light rapidly flashes red and a signal tone sounds.
Note The water pump fills the steam boiler at intervals. If the filling is successful, the LED light is quick flashing red.
Note If there is no or too little water in the steam boiler, the water pump starts to run and pumps water from the water reservoir into the steam boiler. The filling process can take several minutes.

ATTENTION-Damage to the device
Unsuitable water can block the nozzles or damage the water level indicator.

• Do not fill in pure distilled water. Use a maximum of 50% distilled water mixed with tap water.
• Do not use condensation from the clothes dryer for filling.
• Do not use collected rain water for filling.
• Do not use cleaning agents or other additives (e.g. scents) for filling.

1. Fill the water tank with tap water or a mixture of tap water and no more than 50% distilled water. The device is ready for use.

Switching off the device

1. Turn the power switch to the “OFF” position. Illustration M The device is switched off.
2. Move the child lock back. The steam lever is locked.
3. Pull the main plug out of the socket.
4. Drain the water reservoir.

Rinsing out the steam boiler
Rinse the device’s steam boiler out after every tenth filling of the tank.

1. Switch the device off; see Chapter Switching off the device.
2. Allow the device to cool down.
3. Drain the water reservoir.
4. Remove the accessory/accessories from the accessory storage area.
5. Open the maintenance lock. To do this place the open end of an extension tube on the maintenance lock, insert this into the guide so it engages and open it. Illustration S
6. Fill the steam boiler with water and swing it around vigorously. Lime residue which has been deposited on the bottom of the steam boiler will be released as a result.
7. Drain the water completely out of the steam boiler. Illustration T

Storing the device

1. Connect the extension tubes to the large mounts for accessories.
2. Connect a manual nozzle and spotlight nozzle to each extension tube.
3. Fasten the large round brush to the spotlight nozzle.
4. Hang the floor nozzle in the park bracket. Illustration P
5. Wrap the cable and place it in the accessory compartment. Illustration R
6. Wrap the steam hose and place it in the accessory storage area. Illustration Q
7. Place the small round brush and crevice brush in the accessory storage area.
8. Store the device in a dry location that is protected from frost.

Important application instructions

Cleaning the floor areas
We recommend sweeping the floor or vacuum cleaning it before using the appliance. In this way the floor will be cleared of dirt and loose particles before the wet cleaning.

Freshening up textiles
Before using the appliance, always check the compatibility of the textiles at a concealed point: Steam down the textile, allow it to dry and then check it for any change in colour or shape.

Cleaning coated or painted surfaces
ATTENTION- Damaged surfaces
Steam can loosen wax, furniture polish, plastic coatings or paint and edge band from edges.

• Do not direct the steam at glued laminated edges as the edge band may loosen.
• Do not use the appliance for cleaning unsealed wood or parquet floors.
• Do not use the appliance for cleaning painted or plastic-coated surfaces such as kitchen or living room furniture, doors or parquet.

1. To clean these surfaces, steam a cloth briefly and use it to wipe over the surfaces.

Glass cleaner
ATTENTION- Glass breakages and damaged surfaces
Steam can damage sealed points of the window frame and, at low outside temperatures, lead to tension on the surface of window panes and hence to glass breakages. Do not direct the steam at sealed points on the window frame.
At low outside temperatures, heat up the window panes by gently steaming the full surface of the glass.

• Clean the window area with a manual nozzle and cover. To remove the water, use a squeegee or wipe the surfaces dry.

How to use the Accessories

Steam gun
The steam gun can be used for the following applications without accessories:

• To remove slight creases from the hanging clothing items: Steam the clothing item from a distance of 10-20 cm.
• For wiping damp dust: Steam a cloth briefly and use it to wipe over the furniture.

Spotlight nozzle
The spotlight nozzle is suitable for cleaning areas, joins, fittings, drains, sinks, WCs, blinds or radiators that are difficult to access. The closer the spotlight nozzle is to the soiled area, the greater the cleaning efficiency will be as the temperature and steam volume are at their highest at the nozzle opening. Larger lime deposits can be treated before steam cleaning with a suitable detergent. Allow the detergent to soak in for approx. 5 minutes and then steam it off.

1. Slide the spotlight nozzle onto the steam gun. Illustration G

Round brush (small)
The small round brush is used for cleaning stubborn dirt. Stubborn dirt can be removed more easily by brushing.
ATTENTION- Damaged surfaces
The brush may scratch sensitive surfaces. It is not suitable for cleaning sensitive surfaces.

1. Fit the round brush to the spotlight nozzle. Illustration H

Round brush (large)
The large round brush is suitable for cleaning large rounded surfaces, e.g. wash basin, shower tray, bath tub, kitchen sink, etc.
ATTENTION- Damaged surfaces
The brush may scratch sensitive surfaces. It is not suitable for cleaning sensitive surfaces.

1. Fit the large round brush to the spotlight nozzle. Illustration H

• Power nozzle
  The power nozzle is used for cleaning stubborn dirt and for blowing down corners, on joints, etc.

1. Install the power nozzle onto the spotlight nozzle according to the round brush. Illustration H

• Crevice brush

1. The crevice brush is used for cleaning narrow gaps e.g. window recess and cranks in the walls. Illustration H

Manual nozzle
The manual nozzle is used for cleaning small areas that can be washed down, shower cubicles and mirrors.

1. Push the manual nozzle onto the steam gun according to the spotlight nozzle. Illustration G
2. Pull the cover over the manual nozzle.

Floor nozzle
The floor nozzle is used for cleaning washable wall and floor coverings e.g. stone floors, tiles and PVC floors.

ATTENTION- Damage due to build-up of steam
Heat and moisture can lead to damage. Check the heat resistance and steam effect on an inconspicuous area using a minimal volume of steam prior to use.

Note Detergent residue or care emulsions on the surface to be cleaned can lead to streaks during steam cleaning, which will disappear however once these have been used several times.
We recommend sweeping the floor or vacuum cleaning it before using the device. In this way the floor will be cleared of dirt and loose particles before the wet cleaning commences. Work slowly on surfaces that are heavily soiled so that the steam has longer to take effect.

1. Connect the extension tubes with the steam gun. Illustration I
2. Push the floor nozzle onto the extension tube. Illustration J
3. Fasten the floor cleaning cloth to the floor nozzle.
   • a. Place the floor cleaning cloth with the hook and loop fastener strips pointing upwards on the floor.
   • b. Place the floor nozzle onto the floor cleaning cloth, applying slight pressure. Illustration K
     The floor cleaning cloth will stick to the floor nozzle of its own accord due to the hook and loop fastener.

Removing the floor cleaning cloth

1. Place one foot on the bottom corner of the floor cleaning cloth and lift the floor nozzle up. Illustration K
   Note Initially, the floor cleaning cloth’s hook and loop fastener strip is very strong and cannot be removed from the floor nozzle easily. After the floor cleaning cloth has been used several times and washed, it is easier to remove from the floor nozzle and it has reached the optimum adhesion.

Parking the floor nozzle

1. Hang the floor nozzle in the park bracket during work breaks. Illustration P

Carpet glider
The carpet glider is used for freshening up carpets.

ATTENTION- Beware of damaging the carpet glider and carpet

• Contamination on the carpet glider, as well as heat and moisture penetration, can result in the carpet being damaged.
• Before the application, also check the heat resistance and impact of steam on the carpet at an insignificant spot using as small an amount of steam as possible.
• Observe the cleaning instructions from the carpet manufacturer.
• Before using the carpet glider, make sure that the carpet has been vacuumed and that stains have been removed.
• Before application and following operating pauses, remove any possible water accumulation (condensate) in the appliance using evaporating the condensate into a drain (without floor cleaning cloth / with accessories).
• Only use the carpet glider with a floor cleaning cloth on the floor nozzle.
• Steam clean with a weak steam stage when using the carpet glider.
• To prevent too much moistening and to avoid the risk of damage due to temperature effects, do not direct the steam continuously onto one spot (maximum 5 seconds).
• Do not use the carpet glider on deep-pile carpets.

Fastening the carpet glider to the floor nozzle

1. For fastening the floor cleaning cloth to the floor nozzle, please refer to the chapter Floor nozzle. Illustration K
2. Using a little force, allow the floor nozzle to slide into the carpet glider and engage there. Illustration L
3. Start cleaning the carpet.

Removing the carpet glider from the floor nozzle
CAUTION- Beware of burns to your feet
The carpet glider can heat up during the steaming process. Do not operate or remove the carpet glider bare-footed or using open sandals. Only operate or remove the carpet glider using suitable footwear.

1. Press the strap on the carpet glider downwards using the front of toe-capped shoes.
2. Lift the floor nozzle upwards. Illustration L

Iron steam pressure

Note We recommend using the KÄRCHER ironing board with active steam suctioning. This ironing board is optimally matched to the device you have acquired. It facilitates and speeds up the ironing process. In any case, the ironing board used should have a steam-permeable, grid-like ironing base surface.
Note It should be noted that in the case of an ironing board without steam extraction, an ironing board cover can become wet if condensate accumulates.

Initial startup of steam pressure iron
ATTENTION- Material damage due to condensate/moisture

Ironing may cause condensation to drip on the floor and damage sensitive floor coverings. If possible, perform ironing tasks on a floor covering which is insensitive to condensation (e.g. tiles/stone). For sensitive floor covering, ensure that the area on which condensation can drip is adequately protected (e.g. water-impermeable floor mat).
Note The iron plate must be hot to prevent steam from condensing on the sole plate and dripping onto the ironing laundry.
Note Do not turn on the steam stage for the VapoHydro function when the steam pressure iron is plugged in, since otherwise the ironing laundry will get wet.

Recommended steam stages

1. Ensure that tap water or a mixture of tap water and no more than 50% distilled water is in the steam boiler of the steam cleaner.
2. Insert the steam plug of the iron into the unit plug until it clicks into place.
3. Putting the steam cleaner into operation, see chapter Switching on the device.
4. Wait until the steam cleaner is ready for use.
5. The iron is ready for use as soon as the indicator light (orange) has gone out.
6. The warning light comes on during use, when the iron is reheating. The application must not be interrupted during reheating.

Steam ironing
ATTENTION- Damage to garments

• Failure to observe the ironing information in the garment may result in damage.
• Observe the ironing information in the garment.

Note With the fixed, optimal temperature setting, all ironable textiles can be ironed without additional temperature setting. Smooth delicate fabrics and imprints on the back with steam without direct contact with the iron. Steaming the fabrics at a distance of 2 to 3 cm will gently straighten the fibres.
Note The iron is fitted with an automatic switch-off which switches off the device if it has not been moved for more than 5 minutes. This automatic shut-off increases safety and saves energy as the iron does not heat up continuously. The iron will switch back on as soon as it is moved and start heating up.
Note The iron can be held vertically for steaming curtains, dresses, etc.

1. As soon as the heating indicator light (orange) of the iron goes out, ironing can be started.
2. Press the steam switch on the handle below. Steam emits as long as the switch is pressed.
3. Before ironing and after pauses in the ironing process, direct the blast of steam onto a cloth until the steam flows evenly.

Dry ironing

• ATTENTION- Damage to the device
  • Water shortage in the steam boiler leads to damage to the device
  • Make sure that there is water in the steam boiler.
• ATTENTION- Damage to garments
  • Failure to observe the ironing information in the garment may result in damage. Observe the ironing information in the garment.

Note With the fixed, optimal temperature setting, all ironable textiles can be ironed without additional temperature setting.
Delicate fabrics and prints should not be dry-ironed.

• Wait until the heating indicator light (orange) of the iron goes out. The iron is ready for ironing.

Care and service

Descaling the steam boiler
Note Since the lime clogs the appliance, we recommend descaling the appliance based on the number of times the water reservoir is filled as specified in the table (TF=tank fillings).
Note Your water board or municipal utilities authority can provide information on the hardness of tap water.

ATTENTION- Damaged surfaces
The descaler may corrode sensitive surfaces.

Fill and empty the appliance carefully.

1. Switching off the device, see chapter Switching off the device.

2. Allow the device to cool down.

3. Drain the water reservoir.

4. Remove the accessory/accessories from the accessory storage area.

5. Open the maintenance lock. To do this place the open end of an extension tube on the maintenance lock, insert this into the guide so it engages and open it. Illustration S

6. Drain the water completely out of the steam boiler. Illustration T
   ATTENTION Appliance damage due to descaler
   An unsuitable descaler or incorrect dosing of the descaler may damage the appliance. Only use KÄRCHER descaler. Use 1 dosing unit of the descaler for 0.5 l water.

7. Apply descaler solution to the descaler according to the details.

8. Fill the descaler solution into the steam boiler. Do not seal the steam boiler.

9. Allow the descaler solution to take effect for approx. 8 hours.

10. Drain descaler solution completely out of the steam boiler.

11. Repeat the descaling process if necessary.

12. Rinse the steam boiler 2-3 times with cold water to drain all the descaler solution residue.

13. Drain the water completely out of the steam boiler. Illustration T

14. Dry the mounting for the grid connection cable.

15. Close the maintenance lock with an extension tube.

Care of accessories
(Accessories – depending on scope of delivery)
Note The micro fibre cloths are not suitable for dryer.
Note When washing the cloths, observe the instructions on the washing tag. Do not use any liquid softeners as this will affect the ability of the cloths to pick up dirt.

1. Wash the floor cleaning cloths and covers at a max. temperature of 60 °C in the washing machine.

Troubleshooting guide

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

WARNING- Risk of electric shock and burns
Trying to eliminate faults while the appliance is connected to the mains or has not yet cooled down is always dangerous. Remove the mains plug. Allow the appliance to cool down.

• Reduced steam quantity
  The steam boiler is scaled.

  • Descale the steam boiler.

• The LED light is in quick flashing red and a signal tone sounds.
  No water in the water reservoir.

  • Fill the water reservoir.

• The steam lever cannot be pressed

• The steam lever is locked with the child lock.

  • Move the child lock forward. The steam lever is released.

• Long heating-up time
  The steam boiler is scaled.

  • Descale the steam boiler.

• High water output
  The steam boiler is scaled.

  • Descale the steam boiler.

• The steam pressure iron “spits” water

  • Rinse or descale the steam boiler of the steam cleaner; see Chapterl Descale the steam boiler.

• After ironing breaks, water droplets come out of the steam pressure iron
  During longer ironing breaks, steam can condense in the steam line.

  • After pauses in the ironing process, direct the blast of steam onto a cloth until the steam flows evenly.

Technical data

www.kaercher.com/welcome

Rate your product and tell us your opinion.

www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212

References

• Cher - Official Site
• Cleaning equipment and pressure washers | Kärcher International
• Dealer Search | Kärcher International
• Home and Garden Warranty Registration USA - Kärcher
• Reinigungsgeräte und Hochdruckreiniger | Kärcher

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>