K RCHER 59786780 Puzzi 10-1 Carpet Cleaner Instruction Manual

Puzzi 8/1 Register
your product
www.kaercher.com/welcome

59786780 (11/22

59786780 Puzzi 10-1 Carpet Cleaner

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical machine, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE

• Inform your dealer immediately if there is any shipping damage.

• Completely remove the accessories from the box.

• The machine is not suitable for sucking up hazardous dusts as asbestos.
  Please consult your KÄRCHER branch or your KÄRCHER dealer with regard to such applications.

• Only operate the appliance from a grounded outlet. Refer to the Technical data for the necessary main fuse.

SAVE THESE IN-STRUCTIONS
This appliance is intended for commercial use.
SAFETY INSTRUCTIONS
WARNING

To reduce the risk of fire, electric shock, or injury:

1. DISCONNECT APPLIANCE FROM POWER CIRCUIT before removing the cover, performing maintenance work, and when not in use.
2. DO NOT LEAVE the machine unattended when plugged in.
3. ALWAYS CHECK THE POWER SUPPLY CORD for damage or signs of any aging before each use.
4. DO NOT PULL OR CARRY APPLIANCE BY CORD. Do not use cord as a handle. Keep cord away from heated surfaces or fire. Do not close door on cord or pull cord around sharp edges.
5. KEEP CORD AWAY FROM HEAT AND OIL. Do not leave cord lying around after job is complete. It can become a tripping hazard.
6. DO NOT RUN MACHINE OVER CORD.
7. TURN SWITCH TO OFF before unplugging power supply cord.
8. DO NOT UNPLUG BY PULLING CORD. To unplug, grasp plug, not cord.
9. DO NOT GRASP PLUG WITH WET HANDS.
10. A DAMAGED CORD OR PLUG should only be replaced by an authorized service center representative. DO NOT ATTEMPT TO REPAIR POWER CORD.
11. TO AVOID SHOCK, do not expose to rain. Indoor blinds.
12. USE ONLY AS RECOMMENDED BY THIS MANUAL. Use only with recommended attachments.
13. KEEP HAIR, CLOTHING, LOOSE JEWELRY, FINGERS and all parts of the body away from openings and moving parts.
14. DO NOT BLOCK OR OBSTRUCT OPENINGS. Keep openings free of lint, hair, dust, and anything that restricts air flow.
15. DO NOT PICK UP ANYTHING THAT IS BURNING, smoldering, or smoking such as matches, cigarettes, or hot ashes.
16. DO NOT USE TO VACUUM COMBUSTIBLE EXPLOSIVE MATERIALS, such as coal, grain, and other finely divided combustible material.
17. DO NOT USE TO VACUUM COMBUSTIBLE, hazardous, toxic, or carcinogenic materials, including gasoline, diesel fuel, acetone, paint thinner, heating oils, undiluted acids and solvents, pesticide, and asbestos.
18. DO NOT ALLOW APPLIANCE TO BE USED AS A TOY. Keep children away from appliance.
19. DO NOT LEAVE UNATTENDED while appliance is running.
20. DO NOT USE IF CORD, PLUG OR MACHINE IS IN POOR CONDITION. If the Appliance has been dropped, damaged, exposed to weather, or dropped into water; have it checked by an authorized service.
21. ALWAYS USE EYE PROTECTION when operating appliance.
22. USE EXTRA CAUTION when operating on stairs.
23. STAY ALERT! Do not use appliance when you are tired or under the influence of drugs, alcohol or medication.
24. Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
25. To Reduce the Risk of Fire, do not use a flammable or combustible liquid to clean a floor.
26. This appliance is provided with a double insulation. Use only identical replacement parts. See instructions for Servicing of Double-Insulated Appliances.
    Servicing of double-insulated machines

DOUBLE INSULATION

In a double-insulated machine, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated machine, nor should a means for grounding be added to the machine. Servicing a double- insulated machine requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated machine must be identical to the parts they replace.

General notes

Read the original instructions before using the device for the first time and act in accordance with it. Keep this document for future reference or for future owners.

• If the operating instructions and safety instructions are not observed, the device can be damaged and dangers could arise for users and other persons.
• Notify the dealer immediately in the case of shipping damage.
• Check the package contents when unpacking for missing accessories or for damage.

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.
Electrical and electronic appliances contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with the household rubbish.
Notes on the content materials (REACH) Current information on content materials can be found at: www.kaercher.com/REACH

Hazard levels

HAZARD

• Indication of an imminent threat of danger that will lead to severe injuries or even death.

WARNING

• Indication of a potentially dangerous situation that may lead to severe injury

BAIL

• Indication of a potentially dangerous

ATTENTION

• Indication of a potentially dangerous situation that may lead to damage to property.

Intended use

• This spray retraction device is intended for wet cleaning of upholstery, textile covers, and carpets.
• This device is suitable for commercial use, eg in hotels, schools, hospitals, factories, shops, offices, and rental companies.

Overview of the device

Quick Start Guide

Figure A

1. Connect the spray/suction hose to the device, connect the spray/suction hose to the upholstery nozzle
2. Mixing cleaning solution, filling fresh water tank
3. Selecting operating modes
4. Cleaning
5. Emptying the fresh water tank
6. Emptying the wastewater container
7. Filling the fresh water tank(without detergent), rinsing the device
8. Cleaning the fluff filter, cleaning the fresh water filter
9. Allowing the device to dry

Device description

Figure B

1. Upholstery nozzle
2. Holder for accessories
3. Flat type
4. Cable hands
5. Hook for spray/suction hose or cable hook
6. Spray switch
7. Suction switch
8. Casing
9. Steering roller
10. Spray hose connection
11. Suction hose connection
12. Cover
13. Fresh water tank
14. Device carrying handle
15. Nozzle mouthpiece (red)
16. Union nut
17. Lever on the upholstery nozzle
18. Spray hose
19. Suction hose
20. Spray / suction hose
21. Quick Start Guide
22. Wastewater container, removable
23. Wastewater container carrying handle
24. Cover seal
25. Fluff filter
26. Fresh water filter

Table of nozzle mouthpieces

Color| Part number| Flow volume| Application| Approved for device
---|---|---|---|---
Yellow| 6.415-165.0| 0.53 gpm (2.0 l/h)| Floor nozzle| Puzzi 10/ 2
Green| 6.415105.0| 0.18 gpm (0.7 l/h)| Floor nozzle| Puzzi 8/1,
Puzzi 9/1 Bp
Brown| 6.415-166.0| 0.26 gpm (1.0 l/h)| Floor nozzle| Puzzi 8/1,
Puzzi 10/1
Blue| 6.415-928.0| 0.26 gpm (1.0 l/h)| Upholstery nozzle| Puzzi 8/1,
Puzzi 10/1,
Puzzi 10/2,
Puzzi 30/4
Red| 6.415-097.0| 0.15 gal/min (0.55 l/h)| Upholstery nozzle, shorts| Puzzi 8/1,
Puzzi 9/1 Bp

Start-ups

1. Check the power cord, extension cable and hoses for damage before each start-up.

Installing accessories

1. Connect the suction hose to the suction hose connection on the device. Insert the spray hose coupling into the spray hose connection on the device and latch into place.
2. Connect the suction hose to the upholstery nozzle. Connect the spray hose coupling to the upholstery nozzle and latch into place.

Mixing the cleaning solution

DANGER
Danger from detergents Risk of injury and damage Observe all instructions that are included with the detergents used.

Note
Warm water (maximum 122°F/50°C)
increases the cleaning effect. Check the temperature resistance of the surface to be cleaned.
Note

Use detergents sparingly to conserve the environment.

1. Mix fresh water and detergent in a clean container (concentration as specified for the detergent). Dissolve the detergent in the water.

Filling the fresh water tank

1. Pour the cleaning solution into the fresh water tank. The filling level must not exceed the “MAX” mark.

Defoaming agent

Note

Foam is generated in the wastewater container when cleaning previously shampooed carpets. Foaming can be prevented by adding defoaming agents.

1. Add defoaming agent (special accessory) to the wastewater container.

Operation

Switching on the device

1. Connect the mains plug.
2. Press the suction switch to switch on the suction turbine.
3. Press the spray switch to switch on the spray pump.

Fashion cleaning

ATTENTION

Danger from cleaning solution
Risk of damage
Before using the device, check the object to be cleaned for color fastness and water resistance in an inconspicuous place.

1. Remove loose dirt from the object to be cleaned.
2. Press the lever on the upholstery nozzle to spray the cleaning solution.
3. Run over the surface to be cleaned in overlapping paths. Pull the nozzle backwards (do not push).
4. When changing the nozzle, the up-holstery nozzle can be inserted into the holder for accessories.

Switching off the device

1. Switch off the spray switch and the suction switch.
2. Pull out the hands plug.

Empty the wastewater container

1. Switch off the suction switch and the spray switch when the wastewater container is full.
2. Remove the cover.
3. Remove the wastewater container from the device and empty it.

Emptying the fresh water tank

1. Switch off the device.
2. Briefly operate the lever on the upholstery nozzle to relieve pressure.
3. Disconnect the upholstery nozzle from the spray/suction hose.
4. Hang the suction hose in the fresh water tank.
5. Press the suction switch to switch on the suction turbine.
6. Suck the fresh water tank empty and switch off the device.
7. Remove the cover.
8. Remove the wastewater container from the device and empty it.

Flushing the device

1. Connect the upholstery nozzle to the suction hose.
2. Connect the spray hose coupling to the upholstery nozzle and latch into place.
3. For approximately 0.5 gal (2 liters) of tap water into the fresh water tank. Do not add detergents.
4. Press the spray switch to switch on the spray pump.
5. Hold the upholstery nozzle over a drain.
6. Operate the lever on the upholstery nozzle and flush the device for 1 to 2 minutes.
7. Switch off the device.

Each time after use

1. Flush the device.
2. Drain the wastewater container and clean it under running water.
3. Empty the fresh water tank.
4. Clean the exterior of the device with a damp cloth.
5. To avoid unpleasant smells, remove all water from the device before long downtimes.
6. Let the device dry thoroughly: Remove the cover or move it to the side.

Storing the device

1. Wind the hands cable around the carrying handle of the device and the cover.
   Figure C

2. Store the device in a dry room and secure it against unauthorized use.

Cleaning methods

Normal soiling

1. Spray and vacuum up the cleaning solution in one step.

Note
Repeated vacuuming without spraying shortens the drying time.

Heavily soiling or stains

1. Apply cleaning solution with the suction turbine switched off and let it work for 10 to 15 minutes.
2. Clean the area as with normal soiling.

Upholstery cleaning

1. Use less detergent for sensitive fabrics and spray the surface at a distance of approx. 7.9 in (200 mm). Then only vacuum.

Cleaning tips

• Spray heavily soiled areas in advance and allow the cleaning solution to work for 5 to 10 minutes.
• Always work from light to shadow (from window to door).
• Always work from the cleaned to the uncleaned area.
• The more sensitive the covering (oriental bridges, Berber, upholstery fabric) the lower the concentration of detergent.
• Carpets with jute backs can shrink and bleed in color if the work is too wet.
• Brush wet pile carpets in the direction of the pile after cleaning when wet (eg with a fiber brush or scrubber).
• Impregnating after wet cleaning prevents the textile from being quickly soiled again.
• To avoid pressure points or rust stains, do not walk on or furnish the cleaned area until after it has fully dried.
• To improve the cleaning result, rinse the object with clean water after using detergents.

Detergent

6.295-198.0
CarpetPro cleaner (2.6 gal/10 liters)| RM 764 liquid| 1%| 6.295-854.0
CarpetPro impregnation (1.3 gal/ 5 liters)| RM 762 liquid| 20%| 6.295-852.0
Defoaming (0.7 gal/2.5 liters)| RM 761 liquid| 0.5%| 6.291-389.0

For further information, please request the product information sheet and the EU safety data sheet for the relevant cleaning agent.

Transportation

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transportation.

1. Wind the hands cable around the carrying handle of the device and the cover. Place the spray/suction hose in the hook. Insert the upholstery nozzle into the accessory holder.
   Illustration D

2. When transporting the device in vehicles, secure it to prevent it from slipping or overturning in accordance with the respective valid guidelines.

Storage

CAUTION Risk of injury and damage! The device may tip over on sloping surfaces. Be aware of the weight of the device during storage. The device may only be operated indoors.

Care and service

DANGER
Danger of electric shock
Injuries due to touching live parts Switch off the device.
Remove the hands plug.

Clean the fluff filter

1. Remove the cover.
2. Remove the wastewater container from the device.
3. Pull out the fluff filter.
4. Regularly clean the fluff filter under running water. If very dirty, open the frame and replace the fleece.

Clean the fresh water filter

1. Unscrew the fresh water filter.
2. Clean the fresh water filter under running water.

Clean the nozzle

1. Unscrew the union nut.
2. Clean the nozzle mouthpiece.

Troubleshooting guide

DANGER
Danger of electric shock
Injuries due to touching live parts Switch off the device.
Remove the hands plug.
The device is not working

1. Check the socket and the power supply fuse.
2. Check the mains cable and the mains plug of the device.
3. Switch on the device.

No water emitted from the nozzle

1. Fill up the fresh water tank.
2. Check the couplings on the spray hose for correct seating.
3. Clean or replace the nozzle mouth-piece.
4. Clean the fresh water filter.
5. Spray pump defective, contact customer service.

Single-sided spray jet

1. Clean the nozzle mouthpiece.

Poor suction performance

1. Check that the cover is seated correctly.
2. Clean the seal on the cover and the contact surface on the device.
3. Clean the fluff filter.
4. Check the suction hose for clogging; clean if necessary.

Spray pump is loud

1. Refill the fresh water tank.
   Heavy foaming in the wastewater container

2. Add defoaming agent (special accessory) to the wastewater container.

Customer Service department
If the malfunction cannot be corrected, the device must be checked by the Customer Service department.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorized customer service site. (See overleaf for the address)

Accessories and spare parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely. Information on accessories and spare parts can be found at www.kaercher.com .

Technical data

| Puzzle 8/1
---|---
Electrical connection| |
Hands voltage| V| 120
Phase| ~| 1
Power frequency| Hz| 60
Degree of protection| | IPX4
Protection class| | II
Rated current| HAS| 9
Spray pump power| W| 40
Device performance data| |
Fresh water filling quantity| gal (l)| 2.1 (8)
Wastewater filling quantity| gal (l)| 1.8 (7)
Air quantity (max.)| CFM (l/s)| 150 (71)
Vacuum (max.)| mm (kPa)| 2590 (25.4)
Spray pressure| psi (MPa)| 14.5 (0.1)
Spray pressure (max.)| psi (MPa)| 43.5 (0.3)
Volume spray| gal/min (l/min)| 0.26 (1)
Cleaning solution temperature (max.)| °F (°C)| 122 (+50)
Dimensions and weights| |
Typical operating weight| lbs (kg)| 19.0 (8.6)
Length x width x height| in (mm)| 20.5 x 13.0 x 16.5 (525 x 335 x 425)
Ambient conditions| |
Ambient temperature (max.)| °F (°C)| 104 (+40)
Determined values ​​in acc. with EN 60335-2-68
Sound pressure level LpA| dB(A)| 72
Uncertainty KpA| dB(A)| 1
Hand-arm vibration value| m/s²| <2.5
Uncertainty K| m/s²| 0.2
Cable hands| |
Power cord type| | SJTW 2/16 AWG
Part number (CUL)| | 6.648-222.0
Cable length| ft (m)| 33 (10)

Subject to technical modifications.

Accessories

| |

| ****

|
---|---|---|---|---
| 4.130-008.0| DN 32| | 240
| 4.025-004.0| DN 32| |
| 4.321-001.0| DN 32| |
| 4.130-007.0| DN 32| | 240
| 4.130-063.0| DN 32| | 109
| 4.130-000.0| DN 32| |
---|---|---|---|---
| 4.130-001.0| DN 32| | 110
| 4.762-014.0
hard surface adapter,| | | 240
| 4.130-010.0| DN 32| 0.25|
| 5.070-010.0
container for detergent,| | |
| 6.980-078.0| DN 20-26| |
| 6.980-077.0| | |
****| 6.980-080.0| | |

cone connection

THANK YOU! DANKE!
THANK YOU! GRACIAS!

Register your product and benefit from many advantages.
www.kaercher.com/welcome
Rate your product and tell us your opinion.

http://kaer.ch/er/?l=TwSoJtl9IUOwZyAe1rHDyw

www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212

References

• er.com is for sale | www.oxley.com
• Cleaning equipment and pressure washers | Kärcher International
• Cleaning equipment and pressure washers | Kärcher International
• Dealer Search | Kärcher International
• Home and Garden Warranty Registration USA - Kärcher

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>