Golden Lighting 2866-OSF Levitt 14 Wide Semi Flush Outdoor Ceiling Fixture Instruction Manual

June 16, 2024
GOLDEN LIGHTING

**Golden Lighting 2866-OSF Levitt 14 Wide Semi Flush Outdoor Ceiling Fixture Instruction Manual

**

Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the counter top.

Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.

Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

We appreciate your business and hope you love your new light!

Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.

Get function and style! Browse our site for coordinating lights and expert lighting advice

Assembly Instructions

How to Identify the Fixture’s Wires

Hot : Smooth, Black, or Transparent with Black Inner Thread
Neutral : Ribbed, White or Transparent with White Inner Thread
Ground : Copper, Bare Metal, Green, or Transparent Inner Thread

**Get help, quick tips, and explore curated content

Lightinginstructions.com
SCAN ME**

Assembly Instructions

For Customer Service, contact the place of purchase to arrange for replacement parts.

IMPORTANT:

  • All installation work should be done by accredited professional.
  • Shut off power supply at fuse or circuit breaker!
  • Use only the specified bulbs. Do not exceed the maximum wattage!

Assembly Instructions

PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.
PLEASE NOTE: INDOOR/OUTDOOR FIXTURE – IF INSTALLED OUTDOORS, MUST BE PLACED UNDER A COVERED AREA.
Mounting strap ( B ) contains several threaded holes. Two sets of mounting screws ( A & D) should be attached to mounting strap ( B ). You may need to tighten nuts ( C ) that hold mounting screws ( A ) in place. If the screws are not attached, please hold canopy ( F ) up to mounting strap ( B ). Line up the holes in canopy ( F ) with the holes in mounting strap ( B ) and insert mounting screws ( A ) into mounting strap ( B ) so that mounting screws ( A ) protrude through the holes in canopy ( F). Mounting screws ( A ) are long, so please test the canopy against the mounting strap to see how far you should insert the screws. Attach mounting strap ( B ) to the junction box using mounting screws ( D ) and a screwdriver. Tighten the screws securely. Pull the house wires through the center of mounting strap ( B ).

ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.

CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw ( E ) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw ( E ) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.

FINISHING THE INSTALLATION

Push canopy ( F ) up to the ceiling and tightly thread nuts ( G ) and rubber washer ( H ) onto the exposed threads of mounting screws ( A ) until the canopy is snug against the ceiling.
Slide metal shade ( J ) over socket ( I ). Secure the metal shade ( J ) in place using socket ring (K) on the threads of socket ( I ). Thread until secure. Install light bulb (not included) into socket ( I ) in accordance with the fixture’s specifications. Do not exceed maximum recommended wattage. Your installation is complete. Turn on the power and test the fixture.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

GOLDEN LIGHTING User Manuals

Related Manuals