Taylor T-8816P, T-8816 7 Inch Angle Polisher, Sander Owner’s Manual
- June 4, 2024
- TAYLOR
Table of Contents
T-8816P, T-8816 7 Inch Angle Polisher, Sander
Owner’s Manual
OILING INSTRUCTIONS:
OIL AFTER EACH USE WITH 1/2 TEASPOON OF AIR TOOL OIL THROUGH THE AIR INLET.
RUN FOR 1 SECOND TO COAT ALL INTERNAL PARTS
USE 90 PSI MAXIMUM
| Ref # | Part # | Description | Qty. |
|---|---|---|---|
| 1 | 881601 | Plug | 1 |
| 2 | 881602 | Spindle | 1 |
| 3 | 881603 | Key | 1 |
| 4 | 881604 | Retaining Ring | 1 |
| 5 | 881605 | Bearing | 1 |
| 6 | 881606 | Cap Screw | 4 |
| 7 | 881607 | Washer | 8 |
| 8 | 881608 | Spindle Cap | 1 |
| 9 | 8816P09 | Bevel Gear – Polisher | 1 |
| 9 | 881609 | Bevel Gear – Sander | 1 |
| 10 | 881610 | Wave Washer | 1 |
| 11 | 881611 | Retaining Ring | 1 |
| 12 | 881612 | Spacer | 1 |
| 13 | 881613 | Motor Housing | 1 |
| 14 | 881614 | Handle | 1 |
| 15 | 8816P15 | Pinion Gear – Polisher | 1 |
| 15 | 881615 | Pinion Gear – Sander | 1 |
| 16 | 881616 | Front Plate | 1 |
| 17 | 881617 | Rotor | 1 |
| 18 | 881618 | Rotor Blades(4 to set) | 1 set |
| 19 | 881619 | Cylinder | 1 |
| 20 | 881620 | Roll Pin | 1 |
| 21 | 881621 | Rear Plate | 1 |
| 22 | 881622 | O-Ring | 1 |
| 23 | 881623 | Motor Gasket | 1 |
| 24 | 881624 | Spacer | 1 |
| 25 | 881625 | Valve Gasket | 1 |
| 26 | 881626 | Cap Screw | 4 |
| 27 | 881627 | Valve Pin | 1 |
| 28 | 881628 | Locking Lever | 1 |
| 29 | 881629 | Stop Rod | 1 |
| 30 | 881630 | Housing | 1 |
| 31 | 881631 | Valve Seat | 1 |
| 32 | 881632 | Valve Pin | 1 |
| 33 | 881633 | Valve | 1 |
| 34 | 881634 | Valve Spring | 1 |
| 35 | 881635 | Exhaust Gasket | 1 |
| 36 | 881636 | Exhaust Retainer | 1 |
| 37 | 881637 | Exhaust Bushing | 1 |
| 38 | 881638 | O-Ring | 1 |
| 39 | 881639 | Inlet Bushing | 1 |
| 40 | 881640 | Wrench19MM | 1 |
| 41 | 881641 | Pin | 1 |
| 42 | 881642 | Spring Pin | 1 |
| 43 | 881643 | Spring | 1 |
| 44 | 881644 | Bearing | 3 |
| 45 | 881645 | Grease Fitting | 1 |
| 46 | 881646 | Bearing | 1 |
| 47 | 881647 | 7” Velcro Poly Pad | 1 |
| 48 | T-7470A | 7” Rubber Pad (optional) | |
| 49 | T-7472 | 7-1/2” Wool Pad (optional) |
General Instructions Sanders
OIL AFTER EACH USE WITH 1/2 TABLESPOON OF AIR-TOOL OIL THROUGH THE AIR INLET.
RUN FOR ONE SECOND TO COAT ALL INTERNAL PARTS.
IMPORTANT WARNING:
WHEN RUNNING SANDERS, ALWAYS KEEP THE SAND-PAPER ON THE WORK SURFACE.
USE 90 PSI MAX.
- ALWAYS DISCONNECT THE TOOL FROM THE AIR SOURCE WHEN CHANGING ACCESSORIES OR SERVICING THE TOOL.
- USE SAFETY GLASSES, FULL FACE SHIELDS, HEARING PROTECTION, AND GLOVES.
- STAY IN CONTROL OF THE SANDER – DO NOT OVERREACH.
- ALWAYS REMOVE WRENCHES FROM THE TOOL AFTER SERVICING. WRENCHES LEFT ATTACHED MAY RESULT IN SERIOUS HARM TO THE OPERATOR.
- VIBRATION MAY BE HARMFUL TO YOUR ARMS AND HANDS. WEAR PROTECTION.
- INSPECT THE TOOL AND AIR SUPPLY ON A REGULAR BASIS.
- DO NOT REMOVE GUARDS OR SAFETY DEVICES. DO NOT MODIFY OR DEFEAT SAFETY DEVICES.
- DO NOT MAKE CONTACT WITH ELECTRICAL LINES.
- LEAVE THE TRIGGER OFF BEFORE CONNECTING THE TOOL TO THE AIR SUPPLY. AVOID ACCIDENTAL STARTS.
- WEAR THE PROPER CLOTHING. DO NOT WEAR JEWELRY, LOOSE CLOTHING, OR LONG HAIR AS IT CAN GET CAUGHT IN ROTATING PARTS. KEEP GLOVES AWAY FROM ROTATING PARTS.
- DO NOT WORK IN HAZARDOUS ATMOSPHERES WHERE SPARKS COULD IGNITE OR DETONATE FUMES.
- WATCH WHAT YOU ARE DOING. USE COMMON SENSE WHEN OPERATING PNEUMATIC TOOLS. DO NOT USE PNEUMATIC TOOLS WHEN TIRED OR UNDER THE INFLUENCE OF MEDICATION, ALCOHOL, OR DRUGS. SERIOUS PERSONAL INJURY MAY RESULT FROM A MOMENT OF INATTENTION.
- USE 90 PSI AT THE TOOL. USE A 3/8″ HOSE OR LARG-ER WITH FITTINGS 9/32 MINIMUM I.D.
- ONLY USE CLEAN DRY COMPRESSED AIR. NEVER USE OXYGEN, CARBON DIOXIDE, COMBUSTIBLE GASES, OR ANY OTHER BOTTLED GAS TO POWER THIS TOOL.
- SECURE YOUR WORK BEFORE STARTING – USE CLAMPS OR FIND A SUITABLE WAY TO MAINTAIN STABILITY
- STORE TOOLS IN A CLEAN DRY ENVIRONMENT.
- DO NOT USE DAMAGED TOOLS – MARK, AND RETURN THEM FOR SERVICE
- NEVER FORCE THE TOOL. LET THE TOOL DO THE WORK.
- STOP USE IMMEDIATELY IF THE TOOL IS MAKING AN UNUSUAL NOISE OR VIBRATION. HAVE TOOLS CHECKED BY A PROFESSIONAL TECHNICIAN?
- OPERATE AT RATED TOOL SPEED.
- ALWAYS USE SANDING PADS WITH A MAXIMUM SPEED RATING EQUAL TO OR GREATER THAN THE LABELED SPEED OF THE TOOL.
- WORK IN A WELL-VENTILATED AREA AND USE APPROVED PERSONAL PROTECTIVE EQUIPMENT SUCH AS DUST MASKS, THAT ARE SPECIFICALLY DESIGNED TO FILTER OUT MICROSCOPIC PARTICLES. SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING AND OTHER CONSTRUCTION ACTIVITIES CONTAIN CHEMICALS KNOWN TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER REPRODUCTIVE HARM. SOME EXAMPLES OF THESE CHEMICALS ARE CRYSTALLINE SILICA FROM BRICKS, CEMENT, AND OTHER MASONRY PRODUCTS, ARSENIC AND CHROMIUM FROM CHEMICALLY TREATED LUMBER, AND LEAD FROM LEAD-BASED PAINTS. YOUR RISK FROM EXPOSURE VARIES, DEPENDING ON HOW OFTEN YOU DO THIS TYPE OF WORK. TO REDUCE YOUR EXPOSURE TO THESE CHEMICALS WEAR PROTECTIVE MASKS AND CLOTHING.
- KEEP CHILDREN, PETS, AND BYSTANDERS AWAY WHILE OPERATING A PNEUMATIC TOOL. DISTRACTIONS CAN CAUSE YOU TO LOSE CONTROL. PROTECT OTHERS IN THE WORK AREA FROM DEBRIS SUCH AS METAL FILINGS AND SPARKS. PROVIDE BARRIERS OR SHIELDS AS NEEDED.
- THESE WARNINGS AND INSTRUCTIONS CAN NOT COVER ALL POSSIBLE CONDITIONS OR SITUATIONS. THE OPERATOR MUST UNDERSTAND THAT COMMON SENSE AND CAUTION ARE FACTORS THAT CAN NOT BE BUILT INTO THE PRODUCT BUT MUST BE SUPPLIED BY THE OPERATOR.
LIMITED LIFETIME WARRANTY
Most products of Taylor Pneumatic are warranted to be free from defects in
material and workmanship for the life of the tool. This warranty applies to
the original purchaser only. This warranty does not cover tools that have been
abused, misused, modified, not properly lubricated, or to normal wear and
tear. Taylor Pneumatic will at its option repair or replace the defective
product free of charge except for shipping. Taylor Pneumatic’s sole liability
and your exclusive remedy under this warranty are limited to the repair or
replacement of the defective product. There are no other warranties expressed
or implied and Taylor Pneumatic shall not be liable for incidental,
consequential, or special damages, expenses or costs except as described
above. WARRANTY VOID IF TOOL IS DISASSEMBLED. Return tools to Taylor
Pneumatic. Be sure to include your name, address, proof of purchase, and
description of the suspected defect.
This warranty applies to the basic tool. It does not apply to wear and tear on
accessories or consumables such as drill chucks, backing pads for sanders,
punch and dies for nibblers, spray gun cups, or accessories from a kit.
505 N. Railroad Ave. 33435
P.O. Box 1117 33425
Boynton Beach, Florida
SEE OUR CATALOG
atwww.taylorpneumatic.com
Ph.561-732-1111
Fax561-731-4412
Toll Free800-805-8665
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>