winees M3 Pro Indoor Outdoor Security Spotlight Camera User Guide
- June 16, 2024
- winees
Table of Contents
winees M3 Pro Indoor Outdoor Security Spotlight Camera
IN THE BOX
NOTE : If 2 Pack all items will be doubled, except the quick start guide
PRODUCT OVERVIEW
- Microphone
- Light Sensor
- LED Indicator
- Spotlight
- Reset Button
- MicroSD Slot (SD card not included)
- Speaker
APP SETUP
- Scan the OR code below to download the Ai Dot APP Or search for”AiDot” in App Store or Google Play
- Power on the camera, you will hear “Waiting for Wi-Fi configuration” with the camera’s indicator light fiashing in green.
- In the AiDot app, press”+”, select “Scan” to scan the device OR code, and then follow the instructions on App.
- Place the camera in the area where you plan to install to test the video quality, ensure that the camera can work normally after the final installation.
INSTALLATION
Install on the wall
- For a better user experience, we recommend you to install the camera as the below conditions.
- Drill a hole with a 13/64 inch (5.16mm) drill bit, then insert the anchor into the hole. The anchor is necessary for walls that are made by hard materials such as concrete, brick or stucco. (3M tape can be used to fix the position before screw driven in.)
Install on the ceiling
- Install on the ceiling (3M tape can be used to fix the position before screw driven in.)
- Place on the table or other fiat surface (3M tape can be used to fix the position.)
LIGHT INDICATIONS
CAUTIONS
To avoid personal injury and/or possible product damage, the following
cautions must be followed:
- Please use the provided adapter instead of others in case of any damage to the product.
- Keep out of reach of children. This product contains small parts, which can cause choking or injury if ingested.
- To prevent early failure, the camera should only be installed in operating environments ranging between -20°C -50°C(-4°F -122°F).
- Do not install
- close to heat source
- near the metal objects and mirrors that cause radio signal attenuation or shading.
- Do not disassemble or reinstall the camera, otherwise it may cause security risks.
- Unplug the power cord before cleaning. Do not clean the camera with any liquids, spray cleaner or wet cloth.
- The slot and opening are used for ventilation, not allowed to be blocked or covered.
- This product only can be connected to 2.4G WIFI.
Note :
The grantee is not responsible for any changes or modifications not expressly
approved by the party responsible for compliance. Such modifications could
void the user’s authority to operate the equipment.
Note :
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator and your body.
ISED Statement
This device contains licence-exempt transmitter(s) /receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
NEED HELP?
Email our support team: support@iwinees.com
ADDRESS : Linkzone Technology Co., Limited Room 510, 5/F, Wayson
Commercial Building, 28 Connaught Road West, Sheung Wan, Hong Kong
Phone : 1-888-846-6470
Website : www.iwinees.com
Made in China
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.