GIN Yeti Cross 2 Light Square Rescue Parachute User Manual
- June 14, 2024
- GIN
Table of Contents
GIN Yeti Cross 2 Light Square Rescue Parachute
Specifications
- Product Name: Yeti Cross 2
- Purpose: Emergency parachute for paraglider pilots
- Certification: EN 12491:2015 standard
- Maximum Speed for Usage: 32 m/s (115 km/h)
- Repacking Interval: 6 months
- Inspection Interval: 6 months
- Replace Interval: 10 years
BEFORE YOU FLY
GIN rescue parachutes are inspected and packed at the factory. It is recommended that the reserve is repacked by a suitably qualified and experienced paragliding professional or parachute rigger prior to installation into your harness. The efficacy of the rescue, and your life, depend on the correct packing procedure. If in any doubt whatsoever, please seek professional advice from your instructor, GIN dealer or importer.
AIRING
Before packing, the canopy should be aired. Ideally, the canopy should be hung
by its apex from the ceiling for between 6 and 24 hours in a cool, dry room.
PREPARATION
The packing area must be spacious, clean, smooth and dry.
PRELIMINARY MATERIALS
Before starting the packing procedure, make sure you have the following
materials:
- 2 solid weights or sandbags, which should be smooth and clean (2-2.5kg)
- Elastic bands
LAYOUT
Check the serial number that is written on the top center panel and on the re-
packing card first (the re-packing card is attached at the end of this
manual). Fix the risers to a solid point using carabiners.
SPARE PARTS
Elastic bands for repacking are provided in a plastic bag.
PACKING INSTRUCTIONS
LINE CHECK
- Stretch the rescue out to its full length.
- Anchor the riser connection to keep lines tight.
- Check the suspension lines for tangles by the “4 lines check” method:
- All lines should be located inside the first 2 and last 2 lines as illustrated.
FOLDING THE PANELS
- Separate lines as shown:
- Make sure 1 is on TOP, 11 is on BOTTOM, and the Center Line MIDDLE
- Fold in half with all of the panels to the LEFT
NOTE: Use the Gin logo as a reference point.
DIVIDING THE PANELS
Begin to fold all of the panels to the RIGHT. 2 corner sections on each side
should be folded as shown below:
IMPORTANT: The 2 corner sections on each side should be folded as shown.
Once you reach the TOP panel, place weights on the RIGHT side to keep the
folds clean. Fold the rescue in half again, this time onto the RIGHT side.
Repeat steps 1-4 for the LEFT panels.
IMPORTANT: Make sure that all the skirts are even and all the lines are
tight together.
After you have neatly folded both sides of the rescue, check that the panels
are clean and the lines are free of tangle
IMPORTANT: After folding all the panels, check again that the center seams and the inside of the panels are even and lie in the same direction.
INNER BAG FOLDING
- Fold the corner only half way to the center line as shown (45º).
- Next, fold the rescue into 1/4 by folding the left and right edges into the mid-line. Fold the lines as shown.
- Fold the rescue in half.
- Carefully fold the rescue onto itself as shown. 3
- Fold the rescue over the top of the suspension lines.
- Fold the top to make it clean.
- Fold the rescue so that the suspension lines are in the middle, be sure to follow this pattern.
PACKING DEPLOYMENT BAG
Stow the canopy so that the skirt is on top of the folds in the inner bag.
STOWING THE LINES
Start to stow the suspension lines making sure you keep the equal tension on
all lines. Lay the upper suspension lines between the canopy and the inner
bag, and close the three flaps, numbers 1, 2 and 3, with a bight (3cm loop) of
lines through the elastic closure loop.
Stow the lower suspension lines in a ‘figure of 8’ pattern, fixing each pair with rubber bands at each end.
CLOSING THE DEPLOYMENT BAG
Thread the closing loop attached to the deployment bag through the eyelets of
the last flap and place a bight (3cm loop) of suspension lines through the
elastic closing loop. The last 30-50cm of the lines is left free.
TEST
Lifting the bridle, check the force required to allow the lines to free
themselves from the closing loop of the deployment bag. This force should be
around 200g. This force may be verified with a spring balance, if available.
IMPORTANT: Suspension lines should always have equal tension!
DEPLOYMENT BAG WARNING
Yeti Cross 2 has been tested and found compliant using the original Gin
Gliders inner container. The speed of opening and the opening shock test have
been completed using the supplied inner container. Use of any other inner
container may produce different results, including failures.
INSTALLATION INTO THE HARNESS
The Yeti Cross 2 is compatible with GIN harnesses. It may also be compatible
with most other manufacturer’s harnesses, but there is no guarantee of this
and you should check with your instructor or dealer.
OUTER CONTAINER ATTACHMENT
The Yeti Cross 2 can be attached to harnesses that do not have a built-in
rescue container, like the speed glider harnesses. Use of a rescue on these
harnesses requires an outer container bag. You must follow the harness and
outer container bag instructions for proper attachment. If in doubt, consult
with a professional.
ATTACHING THE RESCUE BRIDLE TO THE HARNESS WEBBING
To connect the Yeti Cross 2 to your harness, there are two ways, GIN Rescue
carabiner and Direct loop. If you choose to use a different type of connector,
it should be rated at least 9 times the maximum weight. For example, our
recommended 8mm Stainless Steel screwgate maillon (square) connector has a
minimum breaking load of 28kN (2855 Kgf). It is the pilot’s responsibility to
check the compatibility of the rescue system and ensure that it is installed
properly.
Be sure to inspect your connector during normal maintenance and safety checks. Replace it whenever there are any signs of wear and check your rescue system with a professional after any deployment. We recommend that you cover the connection using the Maillon rapid cover to prevent excess friction. Rubber- bands should also be used to secure the attachment and prevent excess friction.
ATTACHING THE DEPLOYMENT HANDLE
Most harnesses come with their deployment handle. This handle and its strap
must be connected to the deployment bag of the parachute. In particular, check
the length of the strap connecting the rescue deployment handle to the rescue
inner container. It should be long enough that the reserve can be extracted
without the danger of the pins not being pulled before the strap tightens on
the reserve, but not so long that there is excessive slack that extends the
movement required for deployment.
PREFLIGHT CHECKS
For maximum safety, use a complete and consistent system of preflight checks
of your equipment and repeat the same mental sequence at every flight.
Specifically for the rescue, check that:
- There is no visible damage that could affect its airworthiness.
- The rescue parachute container is closed correctly with the pin(s) in place.
- The deployment handle is secured correctly and all parts are in good condition. If any part of the harness/reserve/handle system include Velcro, then this must be separated and re-attached regularly to prevent Velcro ‘bedding in’ over time which can make rescue deployment much more difficult.
DEPLOYMENT PROCEDURE
RESCUE DEPLOYMENT
It is vital to periodically feel the position of the rescue handle in normal
flight so that the action of reaching for the rescue is instinctive in an
emergency.
In the event of an emergency, the pilot must quickly evaluate his or her
height and the seriousness of the incident. On that basis, an instantaneous
decision to deploy the rescue or not must be taken. Deploying the rescue when
the glider is recoverable may increase the danger of injury. If you have
sufficient height and the glider is in a flat spin, it is preferable to first
try to stop the spin (e.g. full stall), due to the risk of entanglement. On
the other hand, a second’s hesitation in deploying the reserve could prove
costly if there is insufficient height.
Procedure
If the rescue is to be deployed, the procedure is as follows:
- Look for the rescue handle and grasp it firmly with one hand
- Pull firmly upwards/sidewards on the handle. This action undoes the Velcro or handles closure and allows the release pins to be pulled out of the release loops, so that the inner container can be released from the harness’ rescue compartment.
- Look for a clear area, and in a continuous motion, throw (and RELEASE!) the rescue as quickly and forcefully as possible away from yourself and the glider. Throwing the rescue in the direction of the air stream will speed opening, and throwing it against the direction of spin will help prevent tangling with the glider.
- After deployment, avoid entanglement and pendulum motions by pulling in the glider as symmetrically as possible with the B, C, D or brake lines
- On landing, be sure to do a PLF (Parachute Landing Fall) to minimize the risk of injury
- Once on the ground, deflate the canopy by pulling on the center line to avoid the possibility of being dragged.
CARE AND MAINTENANCE
The GIN rescue parachute should be repacked at least every 6 months, as
detailed in the packing instructions. We always recommend that this rescue
parachute is inspected and repacked by a trained professional repacker.
Additional inspections should be performed if there is any suspicion of damage
or undue wear.
After a deployment, the rescue should be checked by the distributor or
manufacturer. Always seek professional advice whenever in doubt.
The materials used in the GIN rescue have been carefully selected for maximum
durability. Nevertheless, maintaining your rescue following the guidelines
below will extend its lifetime.
It is recommended that a rescue is replaced after 10 years, even if it has
never been used.
STORAGE
Unnecessary exposure to UV rays, heat, and humidity should always be avoided.
Keep your harness and rescue in your rucksack when not in use.
Store all your paragliding equipment in a cool, dry place, and away from
solvents such as grease, acid, oil, and paint.
Never put your rescue away while damp.
If your rescue parachute ever gets wet (i.e. water landings or snow) you must
remove it from the harness, dry it naturally in the air, and repack it before
putting it back into the container.
A dirty rescue canopy or container can be cleaned with lukewarm water. Mild,
neutral soap may be used if necessary, but do not rub the fabric. Rinse the
canopy thoroughly and allow it to dry naturally. If the canopy shows signs of
mildew or mold, it must be sent to the distributor or manufacturer for
repairs, as the strength could be compromised.
If the rescue is to be stored for an extended period, the canopy should be
opened and loosely rolled.
DAMAGED RESCUE
If there is any noticeable damage to the rescue parachute after inspection,
the rescue must be sent for inspection/repair to the manufacturer.
GIN QUALITY AND SERVICE
We take pride in the quality of our products and are committed to putting
right any problems affecting the safety or function of your equipment and
which are attributable to manufacturing faults. Your GIN dealer is your first
point of contact if you have any problems with your equipment.
If you are unable to contact your dealer or GIN importer, contact Gin Gliders
directly via our website.
GIN LIFETIME GUARANTEE
Gin Gliders is proud to guarantee the quality, craftsmanship, and performance
of all our products. Equipment with defects in materials or manufacturing will
be repaired or replaced at the discretion of Gin Gliders for the practical
lifetime of the product. Equipment damaged through wear and tear, misuse, or
neglect may be repaired at a nominal charge.
If you have any problems with your equipment, please contact your GIN dealer
in the first instance, or Gin Gliders directly via our website.
CARE OF THE ENVIRONMENT
We are privileged to fly in areas of outstanding natural beauty. Respect and
preserve nature by minimizing your impact on the environment. When visiting an
area, contact the local club for details of environmentally sensitive areas
and local restrictions.
Gin Gliders considers the entire life cycle of its products, the last stage of
which is recycling in an environmentally friendly manner. The synthetic
materials used must be disposed of properly. If you are not able to arrange
appropriate disposal, Gin Gliders will be happy to recycle it for you.
Send the equipment with a short note to this effect to Gin Gliders Inc.
RE-PACKING HISTORY
Every effort has been made to ensure that the information in this manual is
correct, but please remember that it has been produced for guidance only.
This owner’s manual is subject to changes without prior notice. Please check
www.gingliders.com for the latest information
regarding the GIN rescue parachute and other GIN products.
Product Registration
Register your product for full warranty benefits:
www.gingliders.com/register
Gin Gliders Inc.
2318-32, Baegok-aero, Mohyeon-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do,
Korea 17036
www.gingliders.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>