GOLDEN LIGHTING 0511-BA3 Malta 3 Light 26 Wide Vanity Light Installation Guide

GOLDEN LIGHTING 0511-BA3 Malta 3 Light 26 Wide Vanity Light

Product Information

Specifications

• Model Number: 0511-BA3
• Power: Maximum Power

Product Usage Instructions

Pendants & Linear Pendants Above a Kitchen Island

Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.

Pendants & Chandeliers Above a Dining Room Table

Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.

Pendants and Chandeliers in Open Areas

The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

Layered Lighting

Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.

Identifying the Fixture’s Wires

Fixture Wires:

• Hot
• Neutral
• Ground

House Wires:

• Hot
• Neutral
• Ground

Ground: Copper, Bare Metal, Green, or Transparent Inner Thread Cable De Tierra: Rosca interior de cobre, metal desnudo, verde o transparente

FAQ

• How do I center a linear pendant over a kitchen island?
  To center a linear pendant over a kitchen island, measure the length of the island and divide it by 2. This will give you the center point. Hang the pendant at this center point.

• How many pendants should I hang above my kitchen island?
  If you are hanging pendants, use one pendant for every 24 inches of the island. For example, if your island is 72 inches long, you should hang three pendants.

• How high should fixtures hang above a dining room table?
  Fixtures should hang at least 30 inches above the table.

• What should be the clearance for pendants and chandeliers in open areas?
  The bottom of the pendant or chandelier should hang at least 7.5 feet from the floor. Make sure to allow clearance for any opening doors.

• How do I identify the wires of the fixture?
  The fixture wires consist of hot, neutral, and ground wires. The hot wire is usually black, the neutral wire is usually white, and the ground wire is usually copper, bare metal, green, or transparent with an inner thread.

Thank You for Choosing Us for Your Lighting Needs

Pendants & Linear Pendants Above a Kitchen Island

Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.

Pendants & Chandeliers Above a Dining Room Table

Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.

Pendants and Chandeliers in Open Areas

The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors

We appreciate your business and hope you love your new light!

• Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
• Get function and style! Browse our site for coordinating lights and expert lighting advice.

How to Identify the Fixture’s Wires

• Hot : Smooth, Black, or Transparent with Black Inner Thread
• Neutral : Ribbed, White or Transparent with White Inner Thread
• Ground : Copper, Bare Metal, Green, or Transparent Inner Thread

Assembly Instructions

Get help, quick tips, and explore curated content

Lightinginstructions.com

For Customer Service, contact the place of purchase to arrange for replacement parts.

IMPORTANT:

• All installation work should be done by an accredited professional.
• Shut off the power supply at the fuse or circuit breaker!
• Use only the specified bulbs. Do not exceed the maximum wattage!

PREPARING FOR INSTALLATION

Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. Mounting strap (A) contains several pairs of threaded holes and two sets of mounting screws (B & C). You may need to tighten the hex nuts that hold screws (B) in place. 2. Place mounting strap (A) up to your junction box. Place backplate (D) over the mounting strap (A) lining up mounting screws (B) with the holes in backplate (D). This will allow you to ensure that you are hanging the fixture straight. 3. Pull the house wires from the junction box and through the center of the mounting strap (A). Secure the mounting strap (A) to the junction box with mounting screws (C) and a screwdriver. Tighten the screws securely.

ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.

CONNECTING THE WIRES

Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.

FINISHING THE INSTALLATION
Place backplate (D) over mounting strap (A) so that mounting screws (B) protrude through the holes in backplate (D). Secure the backplate to the mounting strap with decorative nuts (F). Twist until the backplate of the fixture is snug against the wall. 6. Hold shades (H) up to sockets (G) and secure in place using socket cover (I) and socket ring (J). Adjust the glass to horizontal and vertical. 7. Install light bulbs (not provided) into the sockets (G) in accordance with the fixture’s specifications. Do not exceed maximum recommended wattage. Your installation is complete. Turn on the power and test the fixture.

References

• Lighting Instructions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>