Imilab EC6 Outdoor Security Camera User Manual
- June 16, 2024
- IMILAB
Table of Contents
IMILAB EC6
Outdoor Security Camera
User Manual
Please read this manual carefully before using the device and retain it for future reference.
Product Introduction
- Package list
- Product Appearance
Installing the Device
The device can be wall mounted, ceiling mounted or tied around a support.
-
Wall mounting
1. Attach the wall mounting positioning sticker on the desired installation location on a wall. Drill two holes at the positions indicated on the sticker.
Drilling diameter of around 6.0 mm; drilling depth of around 30mm. 2. Insert two plastic expansion nuts into the wall. Put the baswall. Secure the base plate by inserting the screws into the exnuts.
Nde: After installatim, the p r duct mut be in ha iz mtal han (as shan in the image belay. -
Ceiling mounting
1. Attach the ceiling mounting positioning sticker on the desired installation location on the ceiling. Drill two holes at the positions indicated on the sticker. Drilling diameter of around 6.0 mm; drilling depth of around 30mm. 2. Insert two plastic expansion nuts into the wall. Put the base plate on the ceiling. Secure the base plate by inserting the screws into the expansion nuts.
Nde: After installatim, the prduct mutbe in haizmtal hanging pcitim (as s haw in the image belay. -
Pole mounting
Node: After installation, the prduttmut be in hazmat hanging Pritam (as sham in the image Belo).
Connecting the Device
-
Turn on the camera
Insert the power supply cable into the camera’s power supply port.
Connect the other end of the power supply cable to a power source. -
Insert a microSD card
Ensure that the camera is disconnected from the power supply. Remove the waterproof cap and expose the microSD card slot. Insert the microSD card into the card slot in the direction illustrated.
Note: When inserting or removing the microSD card, please disconnect the camera from the power supply. Please use a microSD card froma reputable manufacturer. The recommended read and write speed of the micro SD card is at least U1/Class 10. -
Restoring factory settings
Press and hold the reset button with fine needle, then you can hear the “reset succeed” voice. Data stored on the microSD card is not deleted.
Not: make sure the voter prefacer is catered after insetingthe micrGDcarda resetting the device.
Connecting to Mi Home App
This product works with Mi Home and can be controlled using the Mi Home
app.Scan the QR code to download and install the Mi Home app. If you already
have Mi Home app installed, you will be directed to the device connection
page. You can also search for “Mi Home” in an app store to download and
install the Mi Home app. Open the Mi Home app.
Tap “+ atthe top right corner and following the on-screen instructions to add
the device.
Note : Actual operation may differ due to Mi Home app update. Please follow the on-screen instructions of the Mi Home app.
About works with mijia
“works with mijia” signifies that the product herein is designator connect and interact with Mi Home app or Mi Al. Please be noted that the product herein is certified by the app interaction only. Xiaomi and Mijia are not responsible for any of the product manufacturing, safety and regulatory standards, or quality supervision.
Specifications
Name: IMILAB EC6 Outdoor Security Camera
Model: CMSXJ65A
Net Weight: 469 g
Resolution: 2880*1620
Input: 12V=1A
Item Dimensions: 161 x 105 x 150 mm
Operating Temperature: -30°C~ 60°C
Wireless Connectivity: Wi-Fi IEEE 802.11 b/g/n/ax 2.4GHz
Freqiency Range: 2400-2483.5 MHZ
EU Max Output Power: s20 dbm
FCC ID: 2APA9-CMSXJ65A
Precautions
- The working temperature of the device is -30°C to 60°C. Do not use the the device when the temperature is too high or too low.
- For better results, avoid placing the camera in front of or next to a glass surface, a white-colored wall or other reflective surfaces as this may cause the recording to have un-even lighting between the foreground and background or be over-exposed.
- Please ensure that the device is within Wi-Fi signal coverage. Place it at a location with good Wi-Fi signal strength.
- Try to avoid placing the device near a metallic object, a midwives oven or otherobj acts that may cause signal interference.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rul es.
Operation is subj ect to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with t he
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. These quip Ent generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur ina particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC 20cm Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator &your body. This transmit er must not be co-located or operating in conjunction with any other antenna po transmier.
WEEE Disposal and Recycling Information
Correct Disposal of this product. This marking indicates that product should not be disposal with other household wastes through out the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environment safe recycling.
Adaptor Statements
Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio eqipment
type IMILAB EC6 Outdoor Security Camera is in complia nce with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available atthe following
internet address: https://www.imilabglobal.com/pages/eu-declartion-of-
conformity
Manufacturer: Shanghai Imilab Technology Co., Ltd.
Address: Roam 001A, Floor 11, Block 1, No. 588
Zixing Road, Minhang District, Shanghai, China
For further information, please go
towww.imilabglobal.com.
Support:[email protected]
Warranty:https://www.imilabglobal.com/pages/warranty
MADE IN CHINA
Documents / Resources
|
Imilab EC6 Outdoor Security
Camera
[pdf] User Manual
EC6 Outdoor Security Camera, EC6, Outdoor Security Camera, Security Camera,
Camera
---|---