Brydge 12.3 Pro+ Wireless Keyboard with Touchpad User Manual
- June 5, 2024
- Brydge
Table of Contents
Brydge 12.3 Pro+ Wireless Keyboard with Touchpad
**INSERT/REMOVE
**
TO INSERT: Place your Brydge on a flat surface and set the hinges upright
to 90 degrees. Insert your Surface Go into the hinges, one side at a time,
with the Wake and Volume Buttons on top.
TO REMOVE: Ensure your Brydge is on a flat surface.
Place your hand towards the back of the keyboard and pull up on your Surface
Go, one side at a time.
POWER
- To manually power on, press and hold Fn + Delete keys. The light will turn green for 2 seconds to indicate power.
- To manually power off, press and hold Fn + Delete keys for 2 seconds. The light will blink red momentarily to indicate it’s powered off.
PAIR
- Turn on your Brydge 10.5 Go+(Fn+Del), then press and hold the Bluetooth key for three seconds. The Delete key light will flash blue confirming your Brydge is in pairing mode.
- On your Surface Go, select:
- Start
- Settings
- Devices
- Bluetooth & other devices
- Add Bluetooth or other device
- Bluetooth
- Brydge 10.5 Go+
- Type in the PIN on your Brydge 10.5 Go+ and hit Enter.
NOTE: If pairing takes longer than three minutes, the blue light will stop flashing and you will need to press the Bluetooth button again.
CHARGE
TO CHECK BATTERY LIFE: go to Windows > SettingsDevices > Bluetooth &
other devices, and check the battery level on ‘Brydge 10.5 Go+’.
NOTE: If battery life is below 15%, the backlit key functionality will be
disabled to conserve remaining battery life and the light on the Delete key
will blink red.
TO CHARGE: Insert the charging cable into the keyboard and plug the other
end into a power source. A solid red LED on the delete key indicates the
Brydge is charging.
When the keyboard is fully charged, the red LED will turn off. A full charge
can take up to three hours.
SLEEP/WAKE
To conserve battery, your Brydge will enter sleep mode after 15 minutes of
non-use. Press any key to wake it.
When you close your devices together, your Brydge will put your Surface Go
into sleep mode. When you open your devices, your Brydge will wake your
Surface Go.
NOTE: Your Brydge will not put your Surface Go to sleep or wake it after 15
minutes of non-use.
PRECISION TOUCHPAD
The Brydge 10.5 Go+ touchpad pairs with your Windows device as a Precision Touchpad, and therefore utilizes all of the Windows touchpad gesture capabilities. To adjust the settings and gestures of your touchpad, select Start > Settings > Devices > Touchpad. The Touchpad can be turned on and off by pressing Fn + Alt.
KEYBOARD SHORTCUTS
Touchpad Disable/Enable
Fn + Alt (Hold Fn & tap Alt to disable. Hold Fn & tap Alt again to enable.)
Language Switch
Win + Spacebar (Use spacebar to toggle through available languages.)
WARRANTY
Thank you for purchasing a Brydge product. This product comes with a 1-year
limited hardware warranty on the terms and conditions set out in this document
and at www.brydge.com/warranty. All Brydge warranties are non-transferrable
and are only available to the original end-user of the product. Warranties do
not apply to products purchased from online vendors unauthorized to sell
Brydge-branded product. If a defect arises during the warranty period, cease
using the product and contact Brydge. To obtain warranty service, visit
www.brydge.com/support or call +1
435-604-0481. Brydge, at its sole
discretion and option, will (1) repair the product at no charge using new
parts or parts that are equivalent to new in performance and reliability, or
(2) replace or exchange the product with a product of equivalent functionality
and value. Brydge offers free return shipping on any approved warranty claims.
A shipping label will be provided to you if you are within the United States.
If you are outside the United States, Brydge will reimburse your return
shipping to a maximum of US$15.00 after providing a copy of the shipping
receipt.
Australia Only: Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure.
Brydge Technologies LLC | 1912 Sidewinder Dr., Suite 104, Park City, UT 84060
USA
HAVE A QUESTION? Visit www.brydge.com/support
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
© 2020 Brydge. All Rights Reserved.
© 2020 Microsoft. Microsoft, the Microsoft logo, Microsoft Surface, Surface,
and the Microsoft Surface logo are trademarks of the Microsoft group of
companies. All other trademarks are the property of their respective owners.
The Bluetooth word mark, and logos are owned by Bluetooth SIG, Inc. Use of
such marks by Brydge is under license. Brydge is a trademark of Brydge Global
Pte. Ltd. Other trademarks and tradenames are those of their respective
owners.