imilab C21 Home Security Camera User Manual
- June 6, 2024
- IMILAB
Table of Contents
imilab C21 Home Security Camera
Product Overview
Package Contents: IMILAB C21 x 1, power cable x 1, wall mounting accessories pack x 1, user manual x 1
Installation
IMILAB C21 can be placed on a number of horizontal surfaces, such as a writing
desk, dining table, and coffee table. It can also be mounted on the wall.
Mounted IMILAB C21 on a Wall:
- Drill two holes on the wall by using the base of the IMILAB C21 as a template. It is recommended that you mark the locations of the hole with a pencil before drilling. The diameter of each hole is approximately 6 mm, and the depth is approximately 30 mm.
- Insert the two plastic anchors into the holes on the wall.
- Make sure to position the base unit so that the arrow is pointing up. Secure the base unit in place by tightening the screws into the plastic anchors.
- Matching the grooves on the bottom of the camera unit with the raised area on the base unit. Press down until the two surfaces are flush, then turn the camera unit in either direction to lock it in position.
Warning: To avoid any damages or injuries, the device must be securely fastened to the floor/wall as specified in the installation instructions. When mounting the security camera on a wall: Please note that the wall must be able to support at least triple the product’s total weight.
Product Instructions
Turning the Device On
MILAB C21will automatically activate once the power cable is inserted into the Micro-USB charging port.
- If the indicator light is flashing orange, that means the device is activated successfully. Else, please reset the device.
- Once the IMILAB C21 is turned on, please do not attempt to rotate its head by force. If the camera position is incorrect, adjustments can be made through the app.
Indicator Light
Steady blue on: connected/device status is normal
Flashing blue: network error
Flashing orange rapidly: waiting for connection
Flashing orange slowly: system upgrade in progress
Installing a MicroSD Card
Make sure that the power to IMILAB C21 is already disconnected. Adjust the
camera lens upward until the MicroSD slot is revealed, then insert the MicroSD
card into the slot (the side with contact points must be facing down).
Note: Please turn off the IMILAB C21‘s power supply before inserting or
removing the MicroSD card. Please use a genuine Micro SD card manufactured by
a qualified supplier, with a reading/writing speed of no less than U1/Class 10.
(Maximum support capacity is 64 GB)
Restore Factory Settings
Press and hold the reset hole with fine needle, then you can hear the “reset
succeed” voice.
Data stored on the MicroSD card is not deleted.
Install IMILAB Home App
Connect with IMILAB Home app. This product works with IMILAB Home app. Control your device with IMILAB Home app. Scan the QR code to download and install the app. You will be directed to the connection setup page if the app is installed already. Or search “IMILAB Home” in the app store to download and install it. Open IMILAB Home app, tap “+” on the upper right, and then follow prompts to add your device.
Add Device
- Open MILAB Home app, tap “+” on the upper right. Tap”[-]”and scan the QR code under the device by your phone, then you can follow the steps to add your device.
- Open MILAB Home app, tap “+” on the upper right. Tap”IMILAB C21”and then you can follow the steps to add your device.
Note: The version of the app might have been updated, please follow the instructions based on the current app version.
Specifications
Name: IMILAB C21 Expandable Memory: MicroSD card (up to 64 GB)
Model: CMSXJ38A Storage: 108 mm x 76 mm x 76 mm
Net Weight : 249 g Operating Temperature: -10 °C to 40 °C
Viewing Angle: 105° Compatible With: Android 5.0 or iOS 9.0 or above
Resolution: 2560 x 1440 Wireless Connectivity: Wi-Fi IEEE 802.11 b/g/n
2.4 GHz
Input: 5 V 2 A
Precautions
- The operating temperature range for this camera is between -10°C and 40°C. Do not use the camera in environments with temperatures above or below the specified range.
- The camera is a precision electronic product. In order to ensure its normal operation, do not install the camera in environments with high humidity levels nor allow water to get into it.
- To improve the camera’s performance, do not place its lens facing or next to a reflective surface, such as glass windows or white walls, as this will cause the image to appear overly bright in areas close to the camera and darker in areas further away, or cause the camera to produce white images.
- Make sure the camera is installed in an area with a strong Wi-Fi signal. Do not place the camera near the objects that may affect its Wi-Fi signal, such as metal objects, microwave ovens.
- Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: This device may not
cause harmful interference, and This device must accept any interference
received, including interference that may cause undesired operation. Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC 20cm Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
WEEE Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
EU Declaration of Conformity
Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio equipment
type IMILAB C21 is in compliance with Directive 2014/53/EU. Manufacturer:
Shanghai Imilab Technology Co., Ltd. Address: Room 001A, Floor 11, Block 1,
No. 588 Zixing Road, Minhang District, Shanghai, China
For further information, please go to
www.imilab.com.
Support: help@imilab.com
References
- 创米imilab官网-智能门-智能家居品牌-全屋智能品牌-扫地机器人
- EU Declaration of Conformity – IMILAB Global
- warranty – IMILAB Global
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>