imilab IPC031 Video Doorbell Set User Manual

: June 5, 2024
: IMILAB

Table of Contents

imilab IPC031 Video Doorbell Set
Getting started
Product overview
Setting up the system
Mounting the video doorbell
Mount the Doorbell on a Wooden Surface
Explanations for LEDS
Safety statement
Precautions
FCC Statement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

imilab IPC031 Video Doorbell Set

Getting started

For video doorbell & hub installation

Product overview

Video Doorbell

Setting up the system

Download the app and set up the system

Download the Imilab Home APP from the app store (ios devices) or google play (Android devices).
Sign up for a similar home account , then follow the onscreen instructions to complete the setup.

Mounting the video doorbell

Find a Mounting Spot Take the video doorbell to your front door and check the live view on the App at the same time. Find a location where you can get the desired ﬁeld of view.
Consider the below factors:

f you want to place the doorbell close to a side wall, make sure the wall doesn’t show up in the ﬁeld of view. Otherwise IR light will be reﬂected and night vision will become blurry.
If you are drilling the mounting holes for the ﬁrst time, the recommended mounting height is 48”/1.2 m from the ground.
Use the 15° mounting wedge as a supplementary mounting bracket if you wish to see more on a speciﬁc side.
Place the Screw Hole Positioning Card against the wall to mark the position.

Mount the Doorbell on a Wooden Surface

If you’re mounting the doorbell on a wooden surface, you don’t need to pre- drill pilot holes. Use tAhe provided screws to secure the Mounting Bracket on the wall, The Screw Hole Positioning Card indicates the position of the screw holes. What is required: Screwdriver, Mounting Bracket, 15° Mounting Wedge , Mounting Screws and Anchors.

Mount the Doorbell on Surfaces Made Out of Hard Materials

If you‘re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco, drill 2 holes through the Screw Hole Positioning Card with a 15/64” (6mm) drill bit.
Insert the provided anchors,and then use provided long screws to secure the Mounting Bracket on the wall. What is required: Power Drill, 15/64”(6mm) Drill Bit, Mounting Bracket, 15° Mounting Wedge , Mounting Screws and anchors.

Mount the Doorbell
Align the doorbell on the bottom and then snap it on top. Press it down until it clicks into place.

You’re all set!
If you want to detach the doorbell or recharge it, please refer to the following sections.

Detach the Doorbell

Use the doorbell detaching pin provided if you wish to detach the doorbell from the Mounting Bracket.
Press and hold the hole on the top of the doorbell and then lift its bottom to take it oﬀ. What is required: Doorbell Detaching Pin

Charging the doorbell

Explanations for LEDS

Safety statement

Speciﬁcations

Name: MILAB Video Model: CMSXJ33A
Doorbell Resolution: 2560×1440 Aperture: F1.6
Item Dimensions: 60 x 33 x 142 mm Power Input: 5 V 2 A
Operating Temperature: -20 °C ~ 50 °C FCC ID：XXXXXXXX
Name: IMILAB Doorbell Hub
Model: CMWG33B
Power Input: 100-240V~，50/60hz，0.3A MAX
Item Dimensions: 57 x 34 x 105mm
Operating Temperature: -10 °C ~ 45 °C
Expandable Memory: MicroSD card(up to 64 GB)
Wireless Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4 GHz
FCC ID：XXXXXXXX

Precautions

The suitable operationg temperature range for this product is between -20℃~50℃. Don’t use the product in an environment with temperatures above or below the speciﬁed range.
When charging, the operating tempreture range for this product is between 0°C~ 45°C. Don’t charge the product in an environment with temperatures above or below the speciﬁed range.
Using the product in a low tempreture environment or charging status will aﬀect its standby time. The actual standby time is related to the user’s environment and habbit. To improve the product’s performance, please do not place the video doorbell lens facing or next to a reﬂective surface, such as glass windows/doors and white walls, which will cause the image to appear overly bright inareas close to the video doorbell and darker in areas further away, or cause the video doorbell to produce white images. Please install the product in areas with Wi-Fi reception, and try to place the device where the Wi-Fi signal is strong. In addition, please keep the security video doorbell away from metal structures, microwave ovens, or other locations where signal strength may be impacted.
Don’t replace the battery in video doorbell yourself—if not properly replaced, there is a danger of explosion.
Battery (battery pack or batteries) must not be exposed to sunlight, ﬁre, or similar overheating conditions.
This product is a low power consumption video doorbell with battery built-in. Don’t use Real-Time Monitoring feature for long time when charging, in order to avoid battery life loss.
Do not use the device in the environment at too high or too low temperature, never expose the device under strong sunshine or too wet enviroment.

FCC Statement

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC 20cm Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

WEEE Information
government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

EU Declaration of Conformity

Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio equipment type IMILAB EC4 is in compliance withDirective 2014/53/EU.
Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio equipment type IMILAB Smart Hub is in compliance with Directive 2014/53/EU.