imilab W11L Smartwatch User Manual
- June 6, 2024
- IMILAB
Table of Contents
imilab W11L Smartwatch User Manual
How to wear correctly
For comfortable daily use, before wearing please place the watch in the suitable position and adjust tightness to fit your wrist. See below picture.
Tip: The heart rate data may be affected if wearing too loosely.
How to pair the watch with your mobile phones
- Long press the side button to turn on the watch, slide the homepage of the dial from top to bottom, open the settings-download the QR code, scan the QR code with your mobile phone, you will get to download and install the APP. Or you can also scan the QR code below to download and install it in the mobile app market.
-
Open the APP GloryFit, enter to device page and select the watch accordingly , then connect the device as guided steps.
Tips:
1.During paring, please ensure mobile phone’s BT is on to ensure the normal connection.
2.2.If the device cannot be found or connected in the pairing process , please reboot the smart watch by long press power button, or choose to reset, then re-search the device. -
How to use the watch
a. Slide down from the homepage to Shortcut Setting Page.
b. Slide up from homepage to the Message Page.
c. Slide right from homepage to Main Menu Page.
d. Slide left from the homepage to Main Function Shortcut Page.
e. Long press the watch face page for 3s to enter into selection page, then slide left or right and click the one you prefer to change dials.
f. Long press the power button for 3s to Power ON; from home page, long press the power button for 3s, and tap√ to Power OFF.
g. Press the power button to pause or continue in Stopwatch page.
h. Tap the power button:
Back to previous menu during normal operation.
Screen on / Screen off at watch face homepage.
Functions
Main Functions Shortcut Page:
Other functions
Alarm clock, Sedentary reminder, Remote Camera control, Low battery reminder, Call reminder, Find smart watch, Watch Face Customized Feature, 12H/24H time format, KM/Mile unit format, Language setting.
Charging
- Place the charging cable into watch charging port, ensuring the metal pins fully connected.
- Please use the correct charging adapters which are 5V 0.5A above.
If smart watch can not be powered on after being left unused for long time, please clean up the charging metal pins to make sure connecting well.
Warranty
- One year warranty is for default hardware defectives, half of year is for battery and charging cable.
- Below reasons cause to defectives are not included in free warranty service:
- Personal assemble or disassemble.
- Falling damage during use.
- All man-made damage or due to the third party’s fault, improper use(such as: water in the smart watch, external force shattering, scratch during use etc.
- Please provide a warranty card with the details filled when request for after selling service.
- Please contact with direct dealers for warranty service.
- Please note all functions of the product are based on physical objects.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
