imilab C30 Home Security Camera User Manual

: June 6, 2024
: IMILAB

Table of Contents

Installation
Product Instructions
Specifications
FCC Statement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

imilab C30 Home Security Camera
User Manual

Product Overview

Package Contents:
IMILAB C30 x 1
power cable x 1,
wall mounting accessories pack x 1,
user manual x 1

Installation

MILAB GO can be placed on a number of horizontal surfaces, such as a writing desk, dining table, and coffee table. It can also be mounted on the wall.
Mounted MILAB C30 on a Wall: 1. Drill two holes on the wall by using the base of the MILAB C30 as a template. It is recommended that you mark the locations of the hole with a pencil before drilling. The diameter of each hole is approximately 6 mm, and the depth is approximately 30 mm.
Insert the two plastic anchors into the holes on the wall.
Make sure to position the base unit so that the arrow I is pointing up. Secure the base unit in place by tightening the screws into the plastic anchors.
Matching the grooves on the bottom of the camera unit with the raised area on the base unit Press down until the two surfaces are flush, then turn the camera unit in either direction to lock it in position.

Warning: To avoid any damages or injuries, the device must be securely fastened to the floor/wall as specified in the installation instructions.
When mounting the security camera on a wait: Please note that the wall must be able to support at least triple the product’s total weight.

Product Instructions

Turning the Device On
MILAB 00 will automatically activate once the power cable is inserted into the Micro-USB charging port.

If the indicator light is flashing orange, that means the device is activated successfully. Else, please reset the device.
Once the MILAB C30 is turned on, please do not attempt to rotate its head by force. If the camera position is incorrect, adjustments can be made through the app.

Indicator Light
Steady blue on connected/device status is normal
Flashing blue: network error
Flashing orange rapidly: waiting for connection
Flashing orange slowly: system upgrade in progress
Installing a MicroSD Card
Make sure that the power to MILAB C30 is already disconnected.
Adjust the camera lens upward until the MicroSD slot is revealed, then insert the MicroSD card into the slot (the side with contact points must be facing down). Note: Please turn off the MILAB C30’s power supply before inserting or removing the MicroSD card. Please use a genuine Micro SD card manufactured by a qualified supplier, with a reading/writing speed of no less than U1 /Class

(Maximum support capacity is 64 GB)

Restore Factory Settings
Press and hold the Reset button more than Ss, then you can hear the “reset succeed” voice.
Data stored on the MicroSD card is not deleted.

Install Imilab Home App
Connect with the Imilab Home app.
This product works with the Imilab Home app. Control your device with the Imilab Home app. Scan the QR code to download and install the app. Or search “Imilab Home” in the app store to download and install it. Open the Imilab Home app, tap “+” on the upper right, and then follow prompts to add your device.

Add Device

Open the Imilab Home app, tap “+’ on the upper right. Tap’ [-]” and scan the QR code under the device by your phone, then you can follow the steps to add your device. •
Open the Imilab Home app, tap “+” on the upper right. Tap” Imilab C30″ and then you can follow the steps to add your device.
Note: The version of the app might have been updated, please follow the instructions based on the current app version.

Specifications

Name: IMILAB 00
Expandable Memory: Micro5D card (up to 64 GB)
Model: CMSXJ21
Dimensions: 112 mm x 75.4 mm x 75.4 mm
Net Weight: 289 g
Operating Temperature: -10 °C to 40°C
Lens Angle: 100°
Resolution: 2560 x 1440
Power input: S V = 2 A
Wireless Connectivity: Wi-Fi IEEE 802.11a/b/g/n/ac2.46112/56Hz FCC ID: 2APA9-CM5X121E

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC 20cm Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
WEEE Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as the terms and conditions of such collection points.
Declaration of Conformity
Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio equipment type MILAB C30 is in compliance with Directive 2014/53/EU.

WARNING
This product can expose you to the chemical Lead which is known to the state of California to cause cancer.
For more information, go y P6swamings.lactam.
Manufacturer: Shanghai Imilab Technology Co., Ltd.
Address: Room 001A, Floor 11, Block 1, No. 588 Zixing Road,
Minhang District, Shanghai, China
For further information, please go to www.imilab.com.
Support: help@imilab.com