Minuteman Tsunami Wet Dry Vacuum Instruction Manual

Minuteman Tsunami Wet Dry Vacuum

Product Information

Technical Specifications

• Model Models: Tsunami T16WD, T16W
• Vacuum Motor: 1.3 HP
• Primothene Squeegee
• Water Lift: 24 inches
• CFM: 95
• Tank Size: 16 Gallons
• Decibel Rating: 74
• Weight: 65 lbs. / 240 lbs. full
• Warranty: Parts – 5 years, Labor – 3 years, Body – 12 years
• Voltage: 115v
• Electric Draw: 13 amps

Important Safety Instructions

Please read and follow these safety instructions to ensure safe operation of the Tsunami Wet/Dry Vacuum:

• Always disconnect the power cord from the electrical outlet before performing any maintenance or cleaning.
• Do not use the vacuum in wet conditions without proper safety precautions.
• Avoid using the vacuum near flammable materials or liquids.
• Keep the vacuum away from children and pets.
• Do not immerse the vacuum in water.
• Use only approved accessories and attachments.
• Do not operate the vacuum with a damaged power cord or plug.
• Do not attempt to repair the vacuum by yourself. Contact customer service for assistance.

Machine Overview

The Tsunami Wet/Dry Vacuum is an industrial vacuum cleaner designed for both wet and dry cleaning applications. It features a powerful 1.3 HP vacuum motor, a Primothene squeegee for efficient water pickup, and a 16-gallon tank for large capacity cleaning. The vacuum is equipped with a 24-inch water lift and produces 95 CFM of suction power. It operates at a decibel rating of 74 and weighs 65 lbs. (240 lbs. when full).

Operating Instructions

Follow these steps to operate the Tsunami Wet/Dry Vacuum:

1. Ensure that the power cord is properly plugged into a grounded electrical outlet.
2. Check that the tank is empty and securely attached to the vacuum body.
3. Select the appropriate attachment or accessory for your cleaning task.
4. Turn on the vacuum using the power switch located on the control panel.
5. Move the vacuum over the desired cleaning area, making sure to cover all areas thoroughly.
6. If using the squeegee attachment for wet cleaning, adjust the height and angle of the squeegee to achieve optimal water pickup.
7. When finished cleaning, turn off the vacuum and unplug it from the electrical outlet.
8. Empty the tank and clean the attachments and accessories as needed.

Squeegee Blade Replacement

If the squeegee blade becomes worn or damaged, follow these steps to replace it:

1. Ensure that the vacuum is turned off and unplugged from the electrical outlet.
2. Remove the old squeegee blade by loosening the screws or clips holding it in place.
3. Position the new squeegee blade in the correct orientation and secure it with the screws or clips.
4. Test the squeegee blade by turning on the vacuum and checking for proper water pickup.

Exploded Views

The following exploded views provide detailed illustrations of the different components and assemblies of the Tsunami Wet/Dry Vacuum:

• Machine Top Level
• Recovery Tank Group
• Tank Cover Assembly
• Rear Cover Assembly
• Vacuum Motor Assembly
• Squeegee Assembly
• Wet/Dry Tool Kit (Included with T16WD)

FAQ

Q: How often should I clean the filters?

A: It is recommended to clean the filters after each use or whenever you notice a decrease in suction power. Regular maintenance of the filters will ensure optimal performance of the vacuum.

Q: Can I use the Tsunami Wet/Dry Vacuum to pick up hazardous materials?

A: No, the Tsunami Wet/Dry Vacuum is not designed for picking up hazardous materials. It is intended for general cleaning purposes. Consult the user manual or contact customer service for guidance on handling specific substances.

Q: How do I replace the vacuum motor?

A: Replacing the vacuum motor should only be done by a qualified technician. Contact customer service for assistance in replacing the vacuum motor.

Minuteman International, Inc.
A Member of the Hako Group
988792 Rev D 10/23

PREFACE

Thank you for your purchase of the new industry standard for wet-dry vacuums. Minuteman International takes great pride in offering the most dependable, reliable and best value in industrial vacuums, power sweepers and sweeper/scrubbers. We set the standard.
Our Customer Service Department would like to hear from you. If you see any errors, omissions
or something that needs clarifi cation in this Parts Catalog please let us know. We are working hard towards continually improving our processes to bring you the best you deserve. Please copy the form below, fi ll out and comment on how you found our catalog.

Please return to:
Customer Service Manager Minuteman International, Inc. 14N845 U.S. Route 20 Pingree Grove, Illinois 60140 USA

Phone: 800-323-9420
Email: tech@minutemanintl.com

Technical Specifications

Model: Tsunami
Models: T16WD, T16W

For Safety When Servicing or Maintaining Machine

• Stop on level surface.
• Disconnect the power to the machine.
• Avoid moving parts. Do not wear loose jackets, shirts, or sleeves when working on machine.
• Authorized personnel must perform repairs and maintenance. Use Minuteman supplied replacement parts.

Important Safety Instructions

COMMERCIAL USE ONLY
When using an electrical appliance, basic precautions should always be followed, including the? following:

READ ALL INSTRUCTIONS BEFORE USING
WARNING: To reduce the risk of fire, electric shock, or injury:

Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.

WARNING
To reduce the risk of electrical shock – Do not expose to rain. Store indoors.

• Do not allow to be used as a toy. Close attention is necessary when used near children.
• Use only as described in this manual. Use only the manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center.
• Do not pull or carry by cord, use cord as handle, close a door on a cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on the cord. To unplug grasp the plug, not the cord.
• Do not handle the appliance with wet hands.
• Do not put any object into the openings. Do not use if any opening is blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust bag and/or filters in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.
• Connect to a properly grounded outlet only. See grounding instructions.
  SAVE THESE INSTRUCTIONS

Inspection
Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly inspected before shipment, and any damage is the responsibility of the delivery carrier who should be notified immediately.

WARNING

• Read Instructions Manual before operating this piece of equipment.
• To reduce the risk of fire use only commercially available floor cleaners and waxes intended for machine application
• Electrical motors and components can cause an explosion when operated near volatile materials and vapors. Do not use this machine near flammable materials such as solvents, thinners, fuels, grain dust, ect.

Electrical – 115V
This machine is designed to operate on a standard 15 amp. 115-Volt, 60hz, AC circuit. Voltages below 105-Volt AC or above 125-Volts AC could cause serious damage to the motor.

Grounding Instructions

• This machine should be grounded while in use to protect the operator from electric shock. The machine is equipped with a three-conductor cord and three prong grounding-type attachment plug to fit the proper grounding-type receptacle. The green (green and yellow) conductor in the cord is the grounding wire. Never connect this wire to anything other than the grounding blade.
• When plugging in the machine, it is intended for use on a 115-Volt (nominal) circuit. If a properly grounded receptacle, as shown in Sketch A, is not available, an adapter as shown in Sketch C, is available and be installed as shown in Sketch B if the outlet box that houses the receptacle is grounded. Be sure to fasten the grounding tab with the faceplate screw.

Machine Overview

Operating Instructions

WET VACUUM

1. Remove cloth/paper bag from recovery tank.
2. Turn on main power switch.
3. Lower the squeegee using the squeegee lift pedal.
4. When recovery tank is full, move the unit to a drain and drain the tank using the dump hose.

DRY VACUUM

1. Install cloth/paper bag in recovery tank.
2. Disconnect solution hose, and install remote tool kit wand to the quick disconnect.
3. Turn on main power switch.

Squeegee Blade Replacement

1. Turn off main power switch.
2. Use squeegee lift pedal to lift squeegee assembly.
3. Hand-loosen 3-sided knobs on squeegee assembly.
4. Slide squeegee assembly off the squeegee plate.
5. Remove screws from the front and back of the squeegee assembly.
6. Slide old blades off , and slide new ones on. (Ridges should be facing outward)
7. Replace screws.
8. Slide squeegee assembly back onto the squeegee plate.(Ensure that the washers are on TOP of the squeegee plate).
9. Hand-tighten 3-sided knobs.

Exploded Views

Machine Top Level

Machine Top Level BOM

BILL OF MATERIAL

ITEM| PART NO.| QTY| DESCRIPTION
1| 511030| 1| HOSE, VACUUM SHORT 1.5 X 33”
2| 511509| 1| ASSEMBLY, SQUEEGEE
3| 511511| 1| RECOVERY TANK GROUP
4| 511512| 1| ASSEMBLY, TANK COVER
5| 511515| 1| KIT, TOOLS, WET/DRY, TSUNAMI
6| 710328| 2| SCR-RHMS 8-32 X .37 ZP
7| 711160| 2| SCR-HI/LO 10 X .625 BLACK ZINC
8| 711552| 2| WASHER-INT LOCK #8
9| 3307719| 1| LATCH-RUBBER SOFT
10| 12310017| 2| WSR-FLT M4.3 X 9 X 0.8 STL 140HV ZD DIN
11| 715914W| 1| DECAL, MINUTEMAN W/SWOOSHES, WHITE

Recovery Tank Group

Recovery Tank Group BOM

BILL OF MATERIAL

ITEM| PART NO.| QTY| DESCRIPTION
1| 172132| 1| FLOAT, SCREENED
2| 173080| 4| WASHER-FLAT .266 X .875 X .07 SS
3| 245310| 2| WASHER, NYLON, .510 B 1.00 OD .062 T
4| 260579| 1| CLIP-TOOL 1.5 INCH HOSE
5| 511000| 1| SHAFT, WHEEL
6| 511001| 2| BRACKET, WHEEL
7| 511002| 2| SPACER, SQUEEGEE
8| 511003| 2| WHEEL, MAIN
9| 511004| 1| PIVOT, SQUEEGEE
10| 511005| 1| CASTER, 5″
11| 511009| 2| SQUEEGEE, BRACKET
12| 511014| 1| HOSE, RECOVERY DRAIN
13| 511043| 1| BEARING-SLEEVE, .377 X .503 X .875
14| 511046| 1| PAD, ANTI-SKID, 1.50 X 2.00
15| 511500| 1| RECOVERY TANK, TSUNAMI
16| 511501| 1| WELDMENT, SQUEEGEE LIFTING BRACKET
17| 511502| 1| WELDMENT, PEDAL
18| 511503| 1| ASSEMBLY, HINGE, TOP COVER
19| 511510| 1| ASSEMBLY, BAG (WD ONLY)
20| 710178| 4| SCR-THMS 1/4-20 X .50 ZP
21| 710528| 2| SCR-FHMS 8-32 X .37 BRASS
22| 711202| 4| SCR-HH 1/4-20 X .50 ZP
BILL OF MATERIAL

ITEM| PART NO.| QTY| DESCRIPTION
23| 711241| 2| SCR-HH 3/8-16 X .75 ZP GR 5
24| 711375| 1| NUT-NYLOC 3/8-16 ZP
25| 711508| 2| WASHER-FLAT 3/8 X 1.00 X .08 ZP
26| 711544| 12| WASHER-LOCK 1/4 SPLIT ZP
27| 711545| 4| WASHER-LOCK 5/16 SPLIT ZP
28| 711546| 2| WASHER-LOCK 3/8 SPLIT ZP
29| 711546| 2| WASHER-LOCK 3/8 SPLIT ZP
30| 711592| 2| WASHER-FLAT .506 X .940 X .064 NYLON
31| 712353| 2| RING-RETAINING E-CLIP 1/2 SS
32| 712565| 4| SCR-THMS 1/4-20 X .62 SS
33| 713044| 1| SCR-HH 3/8-16 X 1.50 ZP GR 5
34| 717040| 2| WASHER-FLAT M10.5 X 30 X 2.5 SS
35| 3303255| 1| CLAMP – SCREW 1″ to 2″ DIA 301SS
36| 3400117| 3| PIN-CLEVIS 3/8 x 1.125 ZP
37| 3400125| 3| RING-RUE 3/8
38| 3400207| 4| SCR-HH 5/16-18 X 0.50 ZP GR 5

Tank Cover Assembly

Tank Cover Assembly BOM

BILL OF MATERIAL

ITEM| PART NO.| QTY| DESCRIPTION
1| 711160| 4| SCR-HI/LO 10 X .625 BLACK ZINC
2| 511506| 1| ASSEMBLY, REAR COVER
3| 511505| 1| ASSEMBLY, VAC MOTOR
4| 511029| 1| COVER, AIR VENT
5| 511025| 1| GASKET, COVER
6| 511024| 1| ADAPTER, HOSE
7| 511054| 1| PLATE, GASKET SUPPORT
8| 712813| 4| SCR-PHMS 10-24 X .75 ZP
9| 712565| 11| SCR-THMS 1/4-20 X .62 SS
10| 511504| 1| TOP COVER, TSUNAMI
11| 173080| 3| WASHER-FLAT .266 X .875 X .07 SS
12| 712758| 13| WASHER-LOCK 1/4 SPLIT SS

Rear Cover Assembly

BILL OF MATERIAL

ITEM| PART NO.| QTY| DESCRIPTION
1| 511027| 1| CORD, PIGTAIL ASM. 12” (120V)
2| 511049-1| 1| PLATE ASSY, REAR COVER, TOP
3| 711310| 2| NUT-HEX 10-32 ZP
4| 809755| 1| SWITCH

Vacuum Motor Assembly

BILL OF MATERIAL

ITEM| PART NO.| QTY| DESCRIPTION
1| 380001| 1| MOTOR-VAC 120V
2| 511018| 1| MOUNT, PLATE
3| 511020| 1| GASKET, VAC MOTOR
4| 511021| 1| GASKET, VAC MOTOR
5| 511022| 1| SEAL, VACUUM MOTOR
6| 511052| 1| GASKET, VAC MOTOR
7| 711124| 1| SCR-PHSMS 10 X .37 ZP B POINT
8| 711160| 4| SCR-HI/LO 10 X .625 BLACK ZINC
9| 742245| 1| WIRE 16G GRN/YEL 14.00″ B= 9

Squeegee Assembly

Squeegee Assembly BOM

BILL OF MATERIAL

ITEM| PART NO.| QTY| DESCRIPTION
1| 210118| 2| KNOB-3 SIDED 5/16 NYLOC
2| 430322| 2| BUSHING-.435 X .625 X .50 ZINC
3| 511034| 2| BLADE, SQUEEGEE PRIMOTHANE
4| 511035| 1| BRACKET, OUTER SQUEEGEE BLADE
5| 511036| 1| BRACKET, INNER SQUEEGEE BLADE
6| 511042| 1| GASKET, SQUEEGEE TOP
7| 511507| 1| WELDMENT, SQUEEGEE PLATE
8| 511508| 2| ASSEMBLY, CASTER
9| 711527| 2| WASHER-FLAT .63 X 1.12 X .09 ZP
10| 712140| 2| WASHER-LOCK 5/16 SPLIT SS
11| 712576| 2| SCR-HH 5/16-18 X 1.25 SS
12| 712770| 18| WASHER-INT TOOTH LOCK #10 SS
13| 712772| 4| WASHER-FLAT .344 X .75 X .06 SS
14| 712822| 18| SCR-THMS 10-24 X .50 SS
15| 730526| 2| WASHER-FENDER M8 X 24 SS
16| 3400318| 2| SCR-HH 5/16-18 X 1.00 SS
17| 3400384| 2| WASHER-CONICAL SPRING 5/16
18| 90548397| 2| ROLLER – PLASTIC, 100MM DIA. (4″)

Wet/Dry Tool Kit (Included with T16WD)

Wet/Dry Tool Kit BOM

BILL OF MATERIAL

ITEM| PART NO.| QTY| DESCRIPTION
1| 282000| 1| WAND 2PC S TYPE ALUM, 38MM ABS CPLNG
2| 282001| 1| HARD FLOOR TOOL, 38MM HORSE HAIR
3| 282004| 1| HAND TOOL 5″ , 38MM
4| 800605| 1| 14″ SQUEE TL W/SLP-ON
5| 282002| 1| CARPET TOOL, 38MM
6| 282005| 1| CREVICE TOOL, 38MM
7| 282003| 1| DUST BRUSH 38MM
8| 511513| 1| HOSE, VACUUM 10′

“More Than Just Clean”

Minuteman is a Full Line Manufacturer of Sweepers and Scrubbers, for Industrial Facilities.

14N845 U.S. Route 20, Pingree Grove, IL 60140 USA Phone 800-323-9420 – www.minutemanintl.com
A Member of the Hako Group

References

• Minuteman Industrial Floor Cleaning Machines | Scrubbers & Sweepers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>