LOREX Halo Series 4K Bullet Camera User Guide

: June 16, 2024
: Lorex

Table of Contents

LOREX Halo Series 4K Bullet Camera
Safety Precautions
What’s Included

LOREX Halo Series 4K Bullet Camera

Specifications

Product Name: Halo Series Lorex H14, H15, H16 E894AB, E894ABB,
E895AB, E896AB, E896DD, E896DDB
Manufacturer: Lorex
Website: lorex.com

Safety Precautions

Follow all instructions for safe use and handling of the product.
Use the camera within given temperature, humidity and voltage levels noted in the camera specifications.
Do not disassemble the camera.
Do not point the camera directly at the sun or a source of intense light.
Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based cleaners.
The supplied cable is rated for surface mounting only (Non-UL). Cables for in-wall and floor-to-floor installations are sold separately (CMR type). These and other cables are available at lorex.com.
It is recommended to connect the camera to the NVR or an external PoE switch. If using a power adapter with this camera, a REGULATED power supply is REQUIRED (not included). Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty.

What’s Included

Note : Based on 1 camera

E894AB, E895AB, E896AB

Tools Needed

Drill
Perceuse

Overview

Cable Notch
Adjustment Screw
Speaker & Siren
MicroSD Card Slot
Reset Button
Smart Security Lighting*
Camera Lens
Warning Lights
Microphone
IR (Infrared) Light

Design differs per model
E896DD, E896DDB

Adjustment Screw
Smart Security Lighting
Microphone
IR (Infrared) Light
Warning Lights
Camera Lens
Cable Notch
MicroSD Card Slot
Reset Button
Speaker & Siren

Camera Placement Tips

Install the camera in a location that is difficult for thieves and vandals to reach.
Secure cabling so that it is not exposed or easily cut.
Point the camera where there is the least amount of obstructions (i.e. tree branches).
Take into consideration what you want to monitor and where is the best coverage area.
Place your camera close to the area of interest. The best position is 10ft/3m above ground, angled 15° down.

Camera Mounting
Test your camera prior to selecting a permanent mounting location, see page 17.
E894AB, E895AB, E896AB

Use the mounting template to drill holes for screws, then insert the drywall anchors. Drill a hole for the camera’s cable if you plan to run it through the mounting surface.
Use the screws to mount the camera base to the surface. If you are running cables along a wall/ceiling, make sure to pass the cable through the cable notch.
Feed the camera’s cable through the camera base, then connect the cables (see page 17).
Loosen the adjustment screw and position your camera as needed, then tighten to secure it in place.
Remove the vinyl film from the camera lens once your installation is complete.

E896DD, E896DDB

Use the mounting template to drill holes for screws, then insert the drywall anchors. Drill a hole for the camera’s cable if you plan to run it through the mounting surface.
Use the Allen key to loosen the camera’s adjustment screw, then remove the dome cover from the camera base.
Use the screws to mount the camera base to the surface. If you are running cables along a wall/ceiling, make sure to pass the cable through the cable notch.
Feed the camera’s cable through the camera base, then connect the cables (see page 17).
Angle your dome camera, then use the Allen key to tighten the dome cover firmly onto the camera base.
Remove the vinyl film from the camera lens once your installation is complete

Camera Connection

Connect your camera directly to your recorder using the camera’s Ethernet extension cable.

Weather-resistant Cap

Twist the Ethernet extension cable’s pre-attached weather-resistant cap securely onto your camera’s Ethernet connector. If exposed to regular precipitation, seal the cap with silicone and electrical tape.

Need Help?
For related support, scan the QR code or visit:

help.lorex.com/E894AB

help.lorex.com/E895AB

help.lorex.com/E896AB
help.lorex.com/E896DD

Register Your Product
producto
Please see our full Terms of Service and Limited Hardware Warranty Policy at: lorex.com/warranty

Copyright © 2023 Lorex Technology Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.

lorex.com help.lorex.com