BLUETTI P020A Split Phase Fusion Box User Manual
- June 5, 2024
- Bluetti
Table of Contents
BLUETTI P020A Split Phase Fusion Box
BRIEF INTRODUCTION
Split Phase Fusion Box is used for connecting two EP500 units (exclusive for the 100-120V version)by bonding them effectively into one larger power system to double the output power,voltage, and capacity to 4000W Max @ 220-240V, 10240Wh.
SAFETY INSTRUCTION
- P020A Split Phase Fusion Box is only designed for EP500 models(100-120V version), it is forbidden to connect P020A to any other power source such as wall outlet, power station, generator or grid.
- DO NOT place the P020A near heat sources. It is prohibited to place the P020A in an environment with flammable, explosive gas, or smoke.
- DO NOT attempt to replace the any internal/exterior component of the equiment by anyone other than authorized personnel.
- DO NOT operate P020A in wet conditions. If the equipment becomes wet,please let the unit dry completely before using.
- Please ensure proper ventilation while in use, inadequate ventilation may cause permanent damage.
- Warning: DO NOT insert foreign objects into any ports of the P020A. P020A generates the same potentially lethal AC power as a household wall outlet.Please use it carefully and keep children away from it.
- In case of the fire, only a dry powder fire extinguisher is suitable for the product.
IN THE BOX
FEATURES OF P020A
- NEMA L14-30: has an L-shaped neutral blade. available in ratings to 20A, allowing for 240V when supplied by split-phase power.
- Standard AC receptacle: wildly used in 100-120V areas, generates the almost same AC power as a household wall outlet.
- AC input interface, to connect P020A to EP500.
Note:
When Split Phase System installation finished successfully, both of the two
LED lights stay ALWAYS ON.
If the LED light is not active, please check the connection.
TECHNICAL SPECIFICATIONS
P020A
| Content| Min.| Rated| Max.| Note
---|---|---|---|---|---
AC Input /
Voltage| 85V| 100/120VAC| 132V| /
Current| | 20A±1A| | /
Frequency| 47Hz| 50/60Hz| 63Hz|
AC Output
①Voltage| 170 VAC| 200/240VAC| 264VAC| NEMA TT-30
①Current| /| /| 20A| Total 20A
②Voltage| 85VAC| 100/120VAC| 132VAC|
②Current| /| /| 20A| Total 20A
③Voltage| 85VAC| 100/120VAC| 132 VAC|
③Current| /| /| 20A| Total 20A
Frequency| 47Hz| 50/60Hz| 63Hz|
General Specs| Min.| Rated| Max.
Working Ambient Temp.| -25℃| 25℃| 50℃
Storage Ambient Temp.| -25℃| 25℃| 60℃
Altitude| /| /| 2000m
Dimension| L272.7mmW134mmH54.3mm
Net Weight| 0.835Kg/1.84lb
Net Weight of Input Cable *2| 0.859/1.89lb
LET`S GET STARTED
CONNECTION 1 (Standard Mode)
Step1.
Connect two EP500 with communication cables. (a-b)
Step2.
Plug the AC Input Cables into P020A from Standard AC receptacle of EP500.
(c-d, e-f).
Step3.
- “Single Phase”: the default machine type as operating one single EP500.
- .Select “Master” or “Slave” on touchscreen of the operating EP500(Tap Settings-Next – Machine Type).
- Tap “Master” on touchscreen will set the operating EP500 as the one to control both two EP500.
- Then select “Slave” on another unit to set the as the one controlled by another one EP500(Master).
- Tap clear the alarm history if the buzzer sounded.
CONNECTION 2 (Power Mode)
In Split Phase Power System, it is recommended to charge the system by the
Fusion AC Input cable.The AC input ports of the two machines are connected to
L1,N,PE and L2,N,PE. Make sure that the phase of the two machines is correct.
This AC Input Cable(Optional Purchase) is designed to match Split Phase
System.
One end of the cable is connected to NEMA L14-30 socket, and the other end is
connected to AC input interface of both two units through aviation plug. It
must be ensured that the phase of the two machines is correct. The current
through AC input plug shall be ≥20A
WRONG CONNECTION
It`s forbidden to build Split Phase System when the AC Input Port of EP500 has
connected into wall outlet.
Please use the Fusion AC Input Cable(Optional Purchase) to charge both of your
power stations in Split Phase System.
Wrong Connection will damage the battery inside the power station and your warranty will be invalid.
DECLARATION
- Some changes may occur without notice such as external appearance or specifications due to availability of material supplies or hardware improvements of the product over time.
- Our company shall not be liable for any damage caused by force majeure such as fires, typhoons, floods, earthquakes or the user’s intentional negligence, misuse or other abnormal conditions.
- No compensation for damages shall be made for utilizing non-standard adapters and accessories.
- This unit is not suitable for use on the relevant equipment or machines involving: Personal safety, such as atomic energy devices, emergency medical devices, etc., or any equipment or machines that require extremely highly reliable power sources. We are not responsible for accidents, fires, wrongful or negligent actions caused by such equipment or machines which results in damage.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>