CARRO ADC523PN-FM Smart Ceiling Fan Installation Guide
- October 30, 2023
- CARRO
Table of Contents
CARRO ADC523PN-FM Smart Ceiling Fan
ITEM: ADC523PN -FM
Technical Parameter: AC 120V 60Hz
SMART CEILING FAN INSTALLATION GUIDE
Please read and follow all the Instructions carefully before using this
product The product image shown here is indicative only. Actual product you
receive may differ.
SAFETY PRECAUTION
IMPORTANT: PLEASE READ BEFORE INSTALLATION:
-
Before you begin installing the fan, shut power Off at the circuit breaker Of the fuse box.
-
OCAUTION: Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
-
Make sure that all electrical connections are in accordance with National Electrical Code, ANSI/NFPA 70 and local codes. Hire a licensed electrician if you are unfamiliar with installing electrical wiring.
-
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance Of 2.1m (7 feet) from the floor and 18 inches from the tip Of the blades to the wall.
-
AWARNlNG: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked “Acceptable for Fan Support of 15.9 kg (35 lbs) or less” and use mounting screws provided with the outlet box.
-
.ACAUTlON: To reduce the risk of injury, use only the screws provided with the outlet box in conjunction with the lock washers provided with the fan.
-
The outlet box and support structure must be securely mounted and capable Of reliably supporting a minimum Of 35 pounds. Use only U.L. listed outlet boxes marked “Acceptable for Fan Support Of 15.9 kg (35 lbs) or less”
-
After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.
-
Do not insert anything into the fan blades while the fan is operating.
-
To change the direction of the rotation of the blades the fan must be in operation mode.
-
All set screws must be checked and retightened where necessary before installation.
-
WARNING : TO reduce the risk Of personal injury, do not bend the blade bracket when installing the brackets, balancing the blades, or cleaning the fan. DO not insert foreign objects in between rotating fan blades
-
CAUTION : To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing the light kit.
-
.After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side Of the outlet box.
-
The splices after being made should be turned upward and pushed carefully up into the outlet box. Conductor wiring identified as grounded is to be connected to a grounded power supply conductor. Conductor wiring identified as an ungrounded conductor is to be connected to an ungrounded conductor. Conductor wiring identified for equipment grounding is to be connected to an equipment-grounding conductor.
-
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING : To reduce the risk of fire or electric shock, this fan must be installed with general use, isolating wall control/switch. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
NOTE : The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may OCCUr. It must be understood that common sense, caution and care are factors which cannot be built into this product. These factors must be supplied by the person (s) installing, caring for and operating the unit. -
CAUTION : The light source is designed for this specific application and can overheat if serviced by untrained personnel. If any servicing is required, the product should be returned to an authorized service facility for examination or repair.
BEFORE YOU START
Contact a licensed electrician if you are uncomfortable performing electrical work. A licensed electrician must install the fan if required by local code. Do not use the fan with a dimmer switch. Turn OFF power at breaker.
Tools and Materials Required
Product instruction
Installation
Disassembling the Motor Assembly:
- Take the motor assembly out Of the box, use a screwdriver to loosen and remove the canopy screws and the mounting plate. Save canopy screws for later use.
- Rotate and take out the motor hub cover as shown in Fig 1.2
Motor Assembly Installation
You have two options for mounting plate installation. Pick which one works
best for your location.
- NOTE: For better fan performance, make sure the mounting plate is level.
- Option 1: Fasten the mounting plate with the wood setscrews (included) when securing to the wooden ceiling beam or support structure with approved electrical outlet box.
- Option 2: IJse machine screws (provided with outlet box) and washers when securing to existing ceiling fan-rated outlet box. If the mounting plate is installed at the outlet box, it should be installed on the outlet box with the screws that came with your outlet box itself. Pull the supply wires (the black, white and ground wires) out of the outlet box and through the hole in the mounting plate and lay them to the side.
- NOTE: DO NOT use the plastic outlet box. Use only U .1_. listed outlet boxes marked”Acceptable for Fan Support of 15.9 kg (35 lbs)or less”.Additional washers (not included) may be needed to insert between the outlet box and mounting plate.
Wiring the Fan:
Carefully lift the fan-motor assembly. Hang the motor assembly on the hook of
the mounting plate by utilizing one of the holes at the outer rim of the motor
housing so that it is securely suspended.
- Connect the fan motor White wire to the supply White (Neutral)wire using a wire nut, connect the fan motor Black wire to the supply Black(Hot/Live)wire using a wire nut. The Yellow/Green wire is ground wire and needs to be connected accordingly. (Make sure all the wires are connected to the correct colors as shown in Fig 3.1
- Re-install two of the four canopy screws (located diagonally from each other) that were removed in step 1 to the mounting plate, but DO NOT tighten them first. Using both hands, lift the fan body from the hook. Align the two key slots in the top of the motor assembly with the two loosened screws on the mounting plate. Push the fan motor assembly up and turn it counterclockwise to lock in the mounting plate. Tighten the two screws. Install back the other two canopy screws into the remaining two holes and tighten the four screws firmly.
Fan Blades Installation:
- Locate 6 blade attachment screws in hardware pack. Install the blade screws to secure each blade to the fan.
- Repeat for the remaining blades. Make sure all the screws are firmly tightened. The installation of the blades is shown in the Fig 4.2.
Installing Back the Motor Hub Cover:
Rotate the motor hub cover clockwise until it locks back to the motor shaft
tightly, After installation, the motor hub cover as shown in Fig 5.2 _
Power on
At this time. the ceiling fan has been installed. Turn on the power supply of
the main switch or the room where the ceiling fan is installed. After power
on, observe whether the fan light is on.
Remote Control Operating Instructions
Pairing the Remote Control to Your Fan
Power on the fan and pair the remote to the fan within I mim To pair remote to
fan, press and hold button for 5 secs to pair remote to the fan. Then test it.
Remote Control button definitions
-
Stops the fan from rotation.
-
Switches between summer mode and winter mode.
- Summer mode – (Counter-clockwise) A downward airflow creates a cooling effect.
- Winter model – (Clockwise)
An upward airflow moves warm air away from the ceiling area and redistributes it around the living space.
-
Turns the fan on and decreases fan speed.
-
Turns the fan on and Increases fan speed.
-
Speed 10 Turns the fan on at highest speed.
-
Speedl Turns the fan on at lowest speed.
-
Turns the fan onloff.
Note: Power on the fan and pair the remote to the fan within 1 min. To pair remote to fan, press and hold@ button for 5 secs to pair remote to the fan. Then test it. -
When the fan is on,press this button and the fan will be shut down 1 hour later.
-
When the fan is on ,press this button and the fan will be shut down 2 hours later.
-
When the fan is on,press this button and the fan will be shut down 4 hours later.
-
When the fan is on ,press this button and the fan will be shut down 8 hours later.
Warning: DO not expose the remote control to direct contact Of water.
Basic product parameters
Care and cleaning
- Check the support connections, brackets, and airfoil attachments twice a year. Make sure they are secure. Because of the fan’s natural movement, some connections may become loose over time. It is not necessary to remove the fan from the ceiling
- Clean your fan periodically. use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing
- (Optional) Apply a light coat of furniture polish to the wood blades.
- (Optional) Cover small scratches With a light application Of shoe polish.
Do not:
- use water when cleaning. Water could damage the motor, or the wood, or possibly cause an electrical shock.
- Apply oil to our fan or motor. The motor has ermanentl lubricated sealed ball bearning
Note :power Off the fan before product maintenance or cleaning the fan.
FCC statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference Will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Troubleshooting
Try these troubleshooting steps before contacting the Customer Service. For
additional operation, maintenance, and troubleshooting information, please
contact our customer service center.
Carro USA Inc. 1431 S.BakerAve. Ontario CA 91761 Tel: 888-253-2374 www.carrohome.com I cs@carrohome.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>