WESTIN 57-924075 HDX Winch Mount Modular Grille Guard Instruction Manual
- June 13, 2024
- Westin
Table of Contents
INSTALLATION INSTRUCTIONS
HDX WINCH MOUNT MODULAR GRILLE GUARD
APPLICATION:
Nissan Frontier 2022
PART NUMBER:
57-924075A
Kit Part Number: 57-924075
57-924075 HDX Winch Mount Modular Grille Guard
CONTENT
ITEM| QUANTITY| DESCRIPTION| TOOLS NEEDED
I| I| WINCH TRAY| 19MM SOCKET
2.| 2| MOUNTING BRACKET, DRIVER (2) AND PASSENGER (3)| 17MM SOCKET
5.| 2| SUPPORT BRACKET. DRIVER (4) AND PASSENGER (5)| RATCHET
6| 2| SPACER PLATE| TORQUE WRENCH
7| 4| MI2-1.25 HEX HEAD BOLT (YELLOW ZINC)| ALLEN WRENCH
8| 8| M 12 SPLIT LOCK WASHER (YELLOW ZINC)|
9| 8| MI2 FLAT WASHER (YELLOW ZINC)|
10| 2| MI2-1.75 HEX HEAD BOLT (YELLOW ZINC)|
II| 2| M10 HEX HEAD BOLT (YELLOW ZINC)|
12| 2| M 10 SPLIT LOCK WASHER (YELLOW ZINC)|
13| 2| M10 FLAT WASHER (YELLOW ZINC)|
14| 2| M 10 SERRATED FLANGE HEX NUT (YELLOW ZINC)|
15| 2| M12 HEX NUT (YELLOW ZINC)|
16| 2| MI2 BOLT PLATE|
17| 2| MI2 PLASTIC RETAINER SQUARE|
18| 6| MI2 HEX HEAD BOLT (BLACK ZINC)|
19| 6| MI2 FLAT WASHER (BLACK ZINC)|
20| 6| M12 SPLIT LOCK WASHER (BLACK ZINC)|
21| 6| MI2 HEX NUT (BLACK ZINC)|
22| 4| MI2 BUTTON HEAD BOLT (BLACK ZINC)|
23| 4| M12 BELLEVILLE WASHER (BLACK ZINC)|
24| 4| MI2 SERRATED FLANGE NUT (BLACK ZINC)|
INCLUDED WITH HDX WINCH MOUNT GRILLE GUARD
25| 1| HDX GRILLE GUARD BASE ASSEMBLY|
26| 1| HDX DRIVER WING|
27| 1| HDX PASSENGER WING|
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT
THREAD DAMAGE AND GALLING
CONTENT
ITEM| QUANTITY| DESCRIPTION| TOOLS NEEDED
28,29| 2| UPPER SUPPORT STRAP DRIVER (28) AND PASSENGER (29)|
30| 2| M8 HEX HEAD BOLT (YELLOW ZINC)|
31| 2| M8 FLAT WASHER (YELLOW ZINC)|
32| 2| M8 SERRATED FLANGE HEX NUT (YELLOW ZINC)|
33| 2| M 12 BUTTON HEAD BOLT (BLACK ZINC)|
34| 2| MI2 BELLEVILLE WASHER (BLACK ZINC)|
35| 2| MI2 SERRATED FLANGE NUT (BLACK ZINC)|
36| 2| MIO BUTTON HEAD BOLT (BLACK ZINC)|
37| 2| MIO BELLEVILLE WASHER (BLACK ZINC)|
38| 2| MIO SERRATED FLANGE NUT (BLACK ZINC)|
39| 10| M8 BUTTON HEAD BOLT (BLACK ZINC)|
40| 10| M8 BELLEVILLE WASHER (BLACK ZINC)|
41| 10| M8 SERRATED FLANGE NUT (BLACK ZINC)|
42| 1| M6 BUTTON HEAD BOLT (BLACK ZINC)|
43| 1| M6 SPLIT LOCK WASHER (BLACK ZINC)|
44| 1| M6 FLAT WASHER (BLACK ZINC)|
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT
THREAD DAMAGE AND GALLING
PROCEDURE
-
Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim. -
Starting on the bottom of the vehicle’s front bumper, remove the plastic clips and OEM hardware. See Figure 1 & 2 for reference.
-
Locate and remove the two plastic retaining clips in the inner wheel well of the vehicle as shown in Figure 3.
-
Start to carefully pry on the retaining clips shown in Figure 4 & 5 along the top of the fascia trim of the vehicle in order to remove the fascia trim. Note: The plastic retainers need to be removed carefully in order to be able to reinstall the fascia trim.
-
Using the supplied M12-1.25 bolts (item 7), M12 split lock washers (item 8), and M12 Flat Washers (item 9), loosely attach the driver side mounting bracket (item 2) to the frame tow hook mounting locations on the under side of the frame.
Note: Ensure that the fine thread M12 hardware is used.
-
Attach the driver side support bracket (item 4). See Figures 7-8.
Note: Ensure that the course thread M12 hardware is used. -
Using the support bracket as a template, mark a location to drill a 1/2” hole in the aluminum crash bar. See Figure 9.
-
Remove the support bracket.
-
Drill a 1/2” hole in the location marked in Step 7.
-
Loosely attach the support bracket using the same hardware from Step 6.
-
Use a M12 fish wire to pull a M12 bolt plate through the aluminum crash bar and use a M12 plastic retainer square to hold it in place.
-
Loosely install the remaining M12 hardware (items 9,8, and 15). See Figure 10.
-
Repeat Steps 5-12 on passenger side of the vehicle to install the passenger side mounting bracket (item 3) and the passenger side support bracket (item 5).
-
Adjust the support brackets so that distance between the inner surfaces is approximately 34.3 inches. See Figure 11.
-
Tighten and torque the support bracket M10 hardware to 25-28 ft-lbs, and the M12 hardware to 50-55 ft-lbs.
-
Reinstall the front bumper fascia using the OEM hardware. Trim fascia as needed.
-
Place the winch tray on top of the mount brackets and loosely attach using the M12 hardware. See Figures 12-13.
-
Install winch at this time per manufacturer’s installation instructions. Note: It may be very difficult to install the winch after the Grille Guard has been installed.
-
On the driver and passenger side of the vehicle, remove the clips at the bottom of the grille. See Figure 14.
-
On the driver side, slide the driver side support strap underneath the grille where the clip was removed.
-
Loosely attach the driver side support strap (item 28) using the yellow M8 hardware and the hole where the clip was removed. See Figure 15.
-
Loosely attach the passenger side support strap (item 29) using the yellow M8 hardware and the hole where the clip was removed.
-
Loosely attach the grille guard base (item 25) to the winch tray and winch tray support bracket using the M12 hardware included with the grille guard and winch tray. See Figure 16.
-
Loosely attach the grille guard base to the support straps using the M10 hardware (items 36-38). See Figure 17.
-
Loosely attach the HDX driver wing (item 26) and HDX passenger wing (item 27) to the grille guard base using the M8 hardware (items 39-41). See Figure 17.
-
Tighten and torque all hardware as specified: M8 hardware to 15-18 ft.-lbs., M10 hardware to 35-38 ft.-lbs., and M12 hardware to 58-60 ft-lbs.
-
The M6 hardware (items 42-44) can be used to attach the Westin license plate relocator (P# 32-0055) to the grille guard
INSTALLATION COMPLETE
WARNING
Failure to follow these instructions could lead to death, personal injury, and
/ or property damage.
Failure to follow these instructions could lead to death, personal injury, and
/ or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance
with the installation instructions and apply torque to the specificationsas
defined. DOUBLE CHECK ALL FASTENERS BEFORE INITIAL USE, AND PERIODICALLY IN
THE FUTURE
TO ENSURE PROPER FUNCTION AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is
defined as required, use caution when drilling a vehicle. FAILURE TO REVIEW AN
AREA TO BE DRILLED MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS
WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO AVOID
PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY: (if applicable)
The Westin Receiver Hitches will have a visible tow rating label affixed
directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight
rating regardless of the capacity of the hitch. FAILURE TO FOLLOW THESE
GUIDELINES WILL VOID THE WESTIN WARRANTY AND MAY RESULT IN PERSONAL INJURY
AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
FOR CALIFORNIA RESIDENTS ONLY-PROP 65 WARNING:
Some products may contain chemicals such as DEHP, which can cause cancer,
birth defects or other reproductive harm. For more info go to
www.p65warnings.ca.gov
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service800-793-7846
www.westinautomotive.com
8/10/2022
P.N.: 75-57924075A-RevA
ECO #: W22-0071
Documents / Resources
|
WESTIN 57-924075 HDX Winch Mount Modular Grille
Guard
[pdf] Instruction Manual
57-924075 HDX Winch Mount Modular Grille Guard, 57-924075, HDX Winch Mount
Modular Grille Guard, Mount Modular Grille Guard, Modular Grille Guard, Grille
Guard, Guard
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>