zalman Z9 ICEBERG MS Atx Mid Tower Computer Case User Manual
- June 16, 2024
- ZALMAN
Table of Contents
zalman Z9 ICEBERG MS Atx Mid Tower Computer Case
- To ensure safe and easy installation, please read the following precautions.
- Product design and specifications may be revised to improve quality and performance without notice.
- www.zalman.com
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specifications
| Model | Z9 Iceberg MS |
|---|---|
| Case Form Factor | ATX Mid-Tower |
| Dimensions | 478 x 245 x 496 (H)mm |
| Weight | 9.6kg |
| Case Materials | Steel, Tempered Glass, Plastic |
| Motherboard Support | E-ATX / ATX / mATX / Mini-ITX |
| Maximum VGA Length | 390mm |
| Maximum CPU Cooler Height | 185mm |
| Maximum PSU Length | 270mm |
| PCI Expansion Slots | 7+3(65mm) |
| Drive Bays | 3.5″ |
| 2.5″ | 3 x 2.5” SSD/HDD or 2 x 3.5” HDD |
Fan Support
| Top| 3 x 120mm / 2 x 140mm
Front| 3 x 120mm / 3 x 140mm / 2 x 200mm(H: 25mm)
Rear| 1 x 120mm / 1 x 140mm
Fan(s) Included| Front| 3 x 140mm ARGB Fan
Rear| 1 x 140mm ARGB Fan
Radiator Support
| Front| 120mm, 140mm, 240mm, 280mm, 360mm
Top| 120mm, 140mm, 240mm, 280mm, 360mm
Rear| 120mm, 140mm
Dust Filter| Top / Front / Bottom
I/O Ports| USB3.0 x 2, USB2.0 x 2, USB3.1 Gen2 Type-C x 1, MIC, HD
Audio, LED Button, Reset Button, Power Button with HDD LED
Accessories component
ASSEMBLING
I/O Ports
| Part| #| Part| #| Part| #| Part
---|---|---|---|---|---|---|---
ⓐ| Power Button
with LED Light
| ⓑ| USB 3.0 Ports| ⓒ| USB 2.0 Ports| ⓓ| Microphone Jack
ⓔ| Headphone Jack| ⓕ| Reset Button| ⓖ| LED Button(1)| ⓗ| USB3.1 Gen2
Type-C
- LED control button for optional LED fans.
Rremoving the side panels
Removing the dust filter
Removing the front panel
Mounting the motherboard
Motherboard size
Mounting PCI-E(VGA) card
Removing the cable cover
Graphic card holder
Mounting the 2.5″ SSD
Mounting the 3.5″ and 2.5″ SSD / HDD
Mounting the 3.5″ and 2.5″ SSD / HDD
Flexible mount of SSD/HDD installation bracket(according to PSU length)
Mounting the PSU
Mounting the radiator
Mounting the fans
Fan(s) Included / Fan Specifications
| Dimensions | 140 x 140 x 25(T)mm |
|---|---|
| Bearing | Sleeve Bearing |
| Input | DC 12V |
| Max.Fan Speed | 900±10%RPM |
| Max.Fan Air Flow | 43.26CFM |
| Max.Fan Noise Level | 21.44dB(A) |
| Fan | 3-Pin |
| LED | 3-Pin(Addressable RGB) |
I/O Connectors
Certification
- This mark, designed by Zalman, indicates product compliance with the European Union’s RoHS (Restriction of Hazardous Substances) Directive.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate
collection systems)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>