LUPINE Sl Minimax Af for E-Bikes Instruction Manual

LUPINE Sl Minimax Af for E-Bikes

Safety instructions

Warning!

• Avoid looking directly into the light emitted by the light or shining the light into your own eyes or the eyes of another person. If the light accidentally shines into your eyes, close your eyes and move your head out of the light beam. Do not use any strongly focusing optical device to look at the light beam.
• In cases where the light is used in a public or commercial setting, users should be provided with trai-ning concerning the safety measures for laser light.
• This device may then be used by children 8 years of age or older, persons with limited physical, sensory or mental capabilities, as well as persons with no previous experience in handling such devices, if they are supervised by a person responsible for their safety.
• Carry a spare light with you at all times, as the product can potentially fail unexpectedly at any time.

Defects:

• Light source must be replaced in general if the light source (or one of the LEDs) is defective.
• In the event of any physical or internal battery failure, do not attempt to repair.
• No user-servicable parts!

Heat generation:
The housing of SL may heat up; so make sure that you always keep the light at a safe distance to any combustible or flammable materials. Could cause fire or death! However, quiescent operation (without cooling the light housing via airflow or the like) is possible at any time and will not damage the product. Always disconnect the battery from the light at transport or storage!

Water resistance:
All SL components are waterproof and can of course be used under extremely severe conditions. The lamp complies with IP protection class 67 but is NOT a diving lamp and is NOT suitable for use under water.

Cleaning:
Do not use a strong water jet or heavy detergent to clean the lamp.

Assembly Instructions

• The included quick release mount needs to be installed on the left side of the lamp head and on the same side on the stem.
• For proper setup screw on the lever of the quick-release mount.

When mounting the quick release, note the position of the O-rings. One O-ring should be between the holder and the lamphead and the other one between the holder and the screw.
Position the lamp centric at the handlebar. Now close the bracket of the quick release so the SL is mounted tight in its position.

Important: The beam must be at least inclined so that its center is only half as high as 5 m away from the headlamp. For this, it may be necessary to adjust the inclination of the mounts.

Battery mounting

Battery type
The battery is mounted with a velcro as shown here. They also come with a capacity indictaor.

Battery mounting
Your battery is supplied with a velcro strap, coated with an anti-slip material to ensure a secure mount. Use the strap which most closely matches your tube size.

Operation

Turn on
By connecting the battery to the lamphead it turns on automatically. The lamp can also be switched on by a short press on the button of the lamp head. Depending on the ambient light, the SL starts lighting either with low beam or daytime running light. Note: Only in the dark when the low beam is activated, it‘s possible to switch into high beam.

Turn off:
To turn off the lamp, keep the button pressed for about 2 seconds.

Bluetooth remote control:
In order to save battery capacity, the remote connection between the lamp and remote control stays active for only 1 hour when the lamp is switched off (standby) and the lamp can be switched on immediately at any time. After that, the lamp may start with a delay, since the signal is only checked every 10 seconds (represented by
a blue blinking of the remote control). After 25 hours, the connection between the lamphead and the remote control will be completely turned off. The lamphead can then only be activated again via the remote control when the lamphead is reconnected to the battery or switched on using the underneath button of the lamphead.

Light mode:
A brightness sensor automatically switches between daytime running light and low beam.

Daylight

• Small button:
• Switch to low beam (Press again to deactivate, sensor is not active)

Big button:

• Without function

Darkness / Night

• Small button:
  • With a short press: Low beam dims to 5Wc (Not possible when ECO 2 is activated)
  • Keep it pressed for about 2 sec.:cActivate daytime running light (Press again to deactivate, sensor is not active)

Big button

• If low beam is activated, switching to high beam is possible.

Customizing the settings at the lamphead
Keep the small button pressed (let go to select) until the lamp lights up as many times you‘ll need it to. Note: It will take about 6 sec. until the programming starts.

Keep the button pressed (let go to select) until SL lights up| Available settings| Explanation
---|---|---
Lights up 1x| ECO 1| High beam: 16W, Low beam: 8W, Daytime running light: 2W
| |
Lights up 2x| ECO 2| High beam: 10W, Low beam: 5W, Daytime running light: 2W
Lights up 3x| Factory setting| High beam: 25W, Low beam: 8W, Daytime running light: 2W
Lights up 4x| Delay (5 sec / 16 sec.) Factory setting: 16 sec.
Sensor calibration
Only in the assembled state! Improper calibration may greatly affect the functionality of the light! Calibrate only outdoors. No artificial light or close to reflective objects!| The sensor controlled switchover from night- to daytime running light occurs as required in either 5 or 16 sec.
Saves the measured brightness value as a switching point from daytime-to nighttime running light. The successful sensor calibration is confirmed by a short illumination of the daytime running light.
Lights up 5x| Reset to factory settings

Note: The light outputs the maximum amount of light only if airflow lowers the temperature of the light sufficiently. If the light is not cooled by airflow, its power is reduced incrementally to prevent the LEDs and electronic elements from overheating.

Lamphead informations

At the remote

• The „high beam symbol“ of the remote lights blue
• High beam is activated.

Battery warning at the lamphead in operation:

• Lamp lights up 1x: 1. Battery Warning, low capacity remaining.
• Lamp lights up several times: Warning!
• The lamp flashes several times. Stop immediately! The light will be switched off.

Capacity indicator

Audible:
To check the capacity, simply press the touch-pad once. At first an audible signal will sound to give a quick reading in 20% steps.

Visible:
The visible indicator uses 5 blue LEDs. The LEDs can operate in two different operating states: blinking and continuous. LED meanings:
A blinking LED is indicating a 10% step and a continuously glowing LED a 20% step.

Example : 3 LEDs steady glow (20 %, 40 %, 60 %) 1 LED blinking (80 %) = 70 % remaining capacity

Bluetooth remote control

The Bluetooth remote comes together with two Peppi V5 barmounts. On the bike, the best way to mount the remote is directly next to your grips so you have full control and don’t need to take off your hands while riding.

Connecting the transmitter to the light:

• By default, your lamp has already been connected to the transmitter.
• Connecting the transmitter to the light:
• If a new remote control is used, follow the step below:
• For establishing a connection, the receiving mode of the lamp has to be activated.
• After connecting the lamphead to the battery, the lamphead is in receiving mode for 15 seconds.
• During this time, press the remote control’s big button for about 5 seconds, until the remote confirms by lighting up blue. Release the button immediately.

Low button cell:
With decreasing voltage, the remote control LEDs will shine less bright. Also cold temperature does reduce the battery voltage.

Transmitter battery change:

• To change the transmitter button cell a T5 star drive key is needed.
• Insert the new CR 2032 button cell as shown and close the transmitter again.
• Tighten the screws until the blue sealing is visibly squeezed.
• T5 star drive key: (Art.No. 137)

App

Lupine Light Control 3.0 – für IOS und Android
The „Lupine Light Control 3.0“ app offers a variety of setting options, for example, for the dimming levels of low and high beams as well as individual light profiles for different activities. In addition, the sensitivity and delay of the light sensor or the start of the battery warning can be set. Furthermore, the matching battery can be saved in the app, which results in the displayed, expected runtime of the lamp.
A version of the app is also available for selected smartwatches, which makes it possible to operate the lamp, including changing the profile, without a smartphone.

Connecting with app:
To connect to the smartphone, the lamp head must be set to receiving mode, which happens automatically after it is plugged into the battery. The pairing mode then is active for 20 seconds.

Product Care, Storage and Charging

Product Care and Storage

Light:
After use in dirty areas clean the lamp and the cables externally with warm water and some mild detergent. Important! Because of the delicate sealings, we do not recommend to open the lamp.
A leakage in consequence of opening the light is excluded from warranty! Before you try to repair something on your own get in touch with our helpful Service Team.

Transport:
Important: Always keep the battery separate from the light, because otherwise the small amount of power used by the electronics will discharge the battery, and the lamp may switch on accidentally. Important! Moreover, the consequent uncontrolled heat buildup could cause a fire or melt the adjacent plastic material.

Battery
If you intend not to use the lamp for a longer period of time, fully charge and store it at a cold and dry place.

Charging batteries

1. Plug the included Wiesel charger into an outlet
2. Connect the charger to the battery, charging starts automatically the LED turns red
3. When the battery is fully charged the LED on charger turns green

• Warning! This charger is to be used to charge rechargeable Li-Ion batteries only. It is NOT suitable for charging NiMH batteries!
• Do NOT use non-rechargeable batteries. – Risk of explosion!
• This charger may be opened ONLY by the manufacturer!

Troubleshooting

Problem                                        Cause Solution

The light does not come on| | Extremely discharged battery| | Charge the battery
---|---|---|---|---
and the power LEDs do not| |
flash when the battery is| | Battery not plugged into the| | Check all plug contacts
plugged into the lamp.| light or not plugged in|
| properly|
The power LEDs do not come| | Faulty LED unit| | LED units needs replacement
on.| | | | Get in touch with Lupine
| | Lamp hasn‘t been used for 5min| | Move the lamp to deactivate
The runtime is too short.| ****

| Discharged or old battery| ****

| Charge battery
| | Old battery| | Replace battery
| | Low ambient temperature| | Keep battery warm
| | Faulty charger| | Replace charger
| | Unsuitable battery| | Use original Lupine battery
Even after charging only the 20% LED will light up at the Smartcore battery.| | The indicator was reseted| | Discharge the battery with your light and fully charge it afterwards
The sensor does not respond.| ****

| The sensor is not exposed| ****

| Make sure the sensor is free from any dirt
The lamp does not recognize the transmitter.|  Lamphead and transmitter are not linked.
Button cell empty or wrong side up.| | See chapter operation remote control.
The lamp changes between low beam and high beam every 6 seconds|

•  Button cell empty
•  Remote control out of range

|

• Replace button cell
• Reduce distance between lamp and remote control

Technical data

Runtime:
with 5.0Ah    with 6.9Ah    with 10.0Ah
battery            battery        battery

Weight

• Lamphead: 100g
• Lamphead with 5.0Ah battery: 290g
• Lamphead with 6.9Ah battery: 340g
• Lamphead with 10.0Ah battery: 450g

Contains:

• FCC ID: QDS-BRCM1078
• IC: 4324A-BRCM1078

Charging time

• SL Mini Max AF 5: 2h 35min
• SL Mini Max AF 7: 3h 35min
• SL Mini Max AF 10: 5h 15min

Battery capacity/nominal voltage:

• SL Mini Max AF 5: 5.0Ah / 7.2 V Li-Ion
• SL Mini Max AF 7: 6.9Ah / 7.2 V Li-Ion
• SL Mini Max AF 10: 10.0Ah / 7.2 V Li-Ion

Approval:
StVZO
K2258

Protection class:
IP67

Charger Wiesel:

• Input voltage: 100 – 240 V~, 50 – 60 Hz
• Charging current: 1.9 A max.
• Compatible batteries: Li-Ion 7.2 V

Operating temperature
-25 °C to +55 °C

More informations at www.lupine.de
EC Declaration of Conformity: www.lupine.de/ce/
Hereby, Lupine Lighting Systems GmbH declares that the radio equipment type SL AX remote is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of conformity is available at the following internet address: https://www.lupine.de/documents/ce

Regulations:
The laws governing the allowable application domain for this lighting system may vary from one country to another. We recommend that you inform yourself about the relevant laws in this domain in your country.

Changes:
Rights for improvements and modifications of our products reserved.

Warranty:

The product’s two year warranty applies to all components, as well as any manufacturing defect. The warranty does not include the battery, however. In addition, any modification or improper use of the product will void the warranty.

Declaration of conformity

Declaration of confirmity Canada:
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Declaration of conformity USA

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Lupine Lighting Systems GmbH Im Zwiesel 9
92318 Neumarkt
Germany

• Phone: +49 (0) 91 81 – 50 94 90
• Fax : +49 (0) 91 81 – 50 94 915
• E-mail : info@lupine.de
• www.lupine.de

FAQ

• Q: How do I adjust the angle of the light beam?
  A: The light beam can be adjusted by modifying the inclination of the mounting arm. The center of the light beam should be half as high at a distance of 5 meters in front of the headlight compared to its exit from the headlight.

• Q: How do I connect the lamp to the Bluetooth remote control?
  A: The lamp is already connected to the Bluetooth remote control by default. If you need to connect a new remote control, please refer to the Bluetooth remote control section in the user manual.

• Q: How do I charge the battery?
  A: To charge the battery, follow the instructions provided in the user manual under the “Laden des Akkus” section.

References

• art.no
• Lupine Lighting Systems - We are the Light
• Lupine Lighting Systems - CE-Dokumente
• Lupine Lighting Systems - CE-Documents
• Lupine Lighting Systems - CE-Documents

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>