YESOUL V5 Bluetooth Fitness Bike Instruction Manual
- June 29, 2024
- YESOUL
Table of Contents
V5 Bluetooth Fitness Bike
“`html
Product Specifications
-
Product model: YS-BV5
-
Item NO.: V5
-
Radio transmission module: CMIIT ID:
2018DP2467 -
Tablet (mobile phone) holder size: Maximum
tablet width: 10.1-inch -
Supporting software version: iOS 11.0 or
higher, Android 5.0 or higher -
Resistance system: Magnetron resistance
system -
Drive mode: Belt drive
-
Power supply: Self-generating
-
Communication mode: Bluetooth+Wi-Fi
-
Height limit: 150 ~ 190cm
-
Rated maximum load: 150kg
-
Net weight: 43.5kg
-
Gross weight: 48.5kg
Product Usage Instructions
Routine Maintenance
It is important to perform routine maintenance on your YESOUL
BIKE V5 to ensure its longevity and optimal performance. Regularly
check for any loose parts and tighten them if necessary. Keep the
bike clean and free of dust and debris.
Installation Guide – List of Parts
To assemble your YESOUL BIKE V5, follow these steps:
-
STEP 1: Check the parts list to ensure you
have all the necessary components. -
STEP 2: Use the provided tools (L-type cross
head hex wrench, open-ended wrench, socket wrench) to assemble the
bike. -
STEP 3: Install the seat cushion by aligning
it with the hole of the sliding seat and locking it in place with
the socket wrench. -
STEP 4: Install the handlebar assembly by
following the provided instructions and using the L-type cross head
hex wrench. -
STEP 5: Install the water bottle cage by
inserting it along the bracket tube at the front of the armrest
assembly.
Frequently Asked Questions (FAQ)
Q: What is the maximum tablet size supported by the tablet
holder?
A: The tablet holder of YESOUL BIKE V5 supports a maximum tablet
width of 10.1 inches.
Q: What is the power supply for the YESOUL BIKE V5?
A: The YESOUL BIKE V5 is self-generating, meaning it generates
power during use and does not require an external power source.
Q: What is the resistance system used in the YESOUL BIKE
V5?
A: The YESOUL BIKE V5 features a Magnetron resistance system for
smooth and adjustable resistance levels.
“`
V5
YESOUL BIKE
Before using this product, carefully read and properly keep this manual.
Product model: YS-BV5 Item NO. :V5 This device contains a radio transmission module with model approval code CMIIT ID: 2018DP2467
YESOUL BIKE V5 Product Manual
Product Parameters
Tablet (mobile phone) holder size Maximum tablet width: 10.1-inch
Supporting software version
iOS 11.0 or higher, Android 5.0 or higher
Resistance system
Magnetron resistance system
Drive mode
Belt drive
Power supply
Self-generating
Communication mode
Bluetooth+Wi-Fi
Height limit
150 ~ 190cm
Rated maximum load
150kg
Net weight
43.5kg
Gross weight
48.5kg
Overall dimensions
(Length) 1250 mm × (Width) 510 mm × (Height) 1230 mm
Routine Maintenance
1. Keep the cycling bike on a dry, ventilated and flat floor. If not used in
a long time, the bike should be covered to keep its body clean and tidy. 2.
Wipe off sweat on the frame with cloth after exercise. Do not wipe the bike
with wet cloth, in order to avoid rusting. 3. Check the belt pulley for
cracking and deviation, and adjust or replace the belt in time. Regularly
clean the belt groove to prevent the belt from jumping out of the groove. 4.
Always check the screws of all body parts for loosening or falling, and
tighten or replace them in time. 5. Always check the resistance adjustment
knob for loosening or falling. Check whether the resistance is reasonable, so
as to calibrate resistance in time. 6. Always check the screws of pedals and
cranks for loosening, and tighten them in time. 7. Always check whether the
saddle is loose and tighten it in time. Wipe the saddle with cotton cloth to
keep it dry.
Important Safety Instructions
Please read them carefully. Improper use may result in
personal injury or death!
1. Make sure that the saddle height adjustment knob is secured correctly, and
will not affect motion during exercise. 2. Keep children and pets away from
this product. This product is for those over 16 years old only. 3. Never
stretch any object or body part into the openings of the bike. 4. The weight
of the user must not exceed the maximum load. 5. Get off the bike until
flywheel/inertial wheel and pedals stop rotating. Otherwise, severe injuries
may be caused due to control failure. 6. If you feel any discomfort, such as
dizziness or breathing difficulty, stop riding the bike and carefully get off.
7. Never turn pedals by hand. or touch any rotating mechanical part;
otherwise, personal injury may be caused. 8. Keep the body hydrated as needed
during riding. 9. Use this product according to the instructions in this
manual. Warm up fully before exercise. 10. Without the preliminary
determination of baseline fitness level and medical certificate signed by a
doctor, never be engaged in high-speed or high-intensity sports. Before
attempting any high-intensity short sprints, pay attention to the body state
and posture, and apply a controllable speed. 11. Wear professional cycling
clothes or tight-fitting sportswear and sports shoes, and tighten foot straps
to avoid injury caused by pulling or entanglement by this product. 12. Never
use this product with inappropriate shoes or barefoot. 13. Incorrect or
excessive training may cause injury. 14. Check whether the bike for loosening
or damage before each use. 15. Never refit this bike or use non-original
accessories without permission. The casing must be opened by professionals, in
order to avoid damage. 16. Those pregnant or with high blood pressure, heart
disease, lumbar spondylosis or reduced mobility must not use this product
without the permission of doctors. 17. In case of any discomfort such as
dizziness or chest pain during exercise, stop exercising immediately and go to
a hospital for examination. 18. If the product fails,stop using it
immediately. 19. This product must not be used for medical rehabilitation. 20.
Use this product on a flat and clean ground. 21. Carry out preventive
maintenance regularly. 22. Never expose this product in a humid place. This
product must not be used outdoor or in any humid place. 23. This product is
for household use (Class H) and not medical fitness equipment. 24. Get off the
bike or enable the emergency brake until inertia wheel and pedals stop
rotating. Otherwise, severe injuries may be caused due to control failure. 25.
Instructions for using the emergency brake: When you want to stop movement,
press down on the emergency brake until it stops. 26.When using the screen
bracket, need to place the device in the center to prevent it from falling.
27.The product should have at least 0.6 meters of free space all around it.
28.Lift the rear tube and the roller on the front tube can move the product
freely or be placed in a suitable position.
Installation Guide – List of Parts
STEP 1: Check of parts List of Parts
NO.
Name
Quantity
Picture
Parts List (Components List)
Frame
1
Front tube
1
Rear tube
1
Pedal set left/right
1
Armrest assembly
1
Tablet
(mobile phone)
1
holder
Water bottle cage
1
Seat cushion
1
Dumbbell rack
1
2×Umbrella head hexagon socket screws M8×60L/ Arc gasket
2×Umbrella head hexagon socket screws M8×60L/ Arc gasket
(left)
(right)
2×Semi-round head phillips screws M6×12
4×Cylindrical head hexagon socket screws M8×12L/spring washer
1 × Umbrella head hexagon screw M8 × 35L
1×Bag cap nut
Installation Guide – List of Parts
Parts List (Components List)
NO.
Name Quantity
Picture
Sliding seat
1
1×Flat pad
1×Carriage screw M8×45L
1×Sliding seat
1×Round flower knob
Instructions
1
Instructions
Accessories List (Tools List)
NO.
Name Quantity
A
L-type cross head hex wrench 6#
1
B
Open-ended wrench
1
C
Socket wrench
1
Picture
*In order to facilitate assembly, some accessories have been installed on the body before delivery.
Installation Guide
STEP 2: Installation of bottom tube 1. Take L-type cross head hex wrench 6#
(A) out of the ziplock bag. 2. Remove four umbrella head hexagon socket screws
(M8×60L) and arc gaskets of the front tube and rear tube via the L-type cross
head hex wrench 6#(A).
L-type cross head hex wrench 6#(A)
3. Align the holes of the front and rear front tube and rear tube with the
bottom holes of the frame , manually screw the arc gaskets and umbrella head
hexagon socket screws (M8×60L), and tighten then via the L-type cross head hex
wrench 6# (A).
Installation Guide
STEP 3: Install the slide seat 1. Use your hands to remove the carriage screws
(M8×45L)flat pad and round flower knob pre-installed on the sliding seat ; 2.
Place the sliding seat on the sliding tube and align it with the hole; 3.
Tighten the carriage screw (M8×45L)flat washer and round flower knob (as shown
in the picture) in sequence by hand.
STEP 4Installation of dumbbell rack 1. Use L-type cross head hex wrench 6#(A)
and socket wrench (C) to remove the umbrella head hexagonal screws (M8×35L)
and bag cap nut pre-installed on the dumbbell rack respectively; 2. Place the
dumbbell rack on the sliding tube and align it with the hole; 3. Install the
umbrella head hexagonal screws (M8×35L) in the umbrella head into the hole by
hand, then screw in the bag cap nut, and tighten it with L-type cross head hex
wrench 6#(A)and socket wrench (C) respectively;
L-type cross head hex wrench 6#(A)
Socket wrench(C)
Installation Guide
STEP 5Install cushion 1. Take out the seat cushion from the ziplock bag; 2.
Align the seat cushion with the hole of the sliding seat and insert it, use a
socket wrench (C) to lock it in the direction of the arrow.
Socket wrench(C)
STEP 6: Installation of handlebar assembly 1. Use L-type cross head hex wrench
6#(A) to remove the four cylindrical head hexagon socket screws (M8x12L) and
spring washers pre-installed in the handrail assembly . 2. Connect the wire in
the front tube to the wire inside the front (as shown in the figure), be
careful to untie the tie after connection and then insert the wire into the
tube without pressing the wire;
L-type cross head hex wrench 6#(A)
Align the port to connect to the screen connection cable * Please make sure
that the connection direction is correct. Please do not connect it with
violence.
Installation Guide
3. First, raise the head tube to the direction of the arrow for a certain
distance, handrail assembly from the top to the bottom of the alignment of the
hole with the hand to screw cylindrical head hexagon socket screw (M8x12L) and
spring washer into the hole in turn; 4. Lock the screws with the L-type cross
head hex wrench 6# (A).
Note: The handlebar assembly should be aligned with the head tube holes!
STEP 7: Installation of water bottle cage 1. Take out the water bottle cage
and open it with a little force. Then insert it along the bracket tube at the
front of the armrest assembly and install it to the appropriate position.
Installation Guide
STEP 8: Installation of tablet (mobile phone) holder 1. Remove two semi round
head phillipsscrews (M6×12) pre-installed on the handle assembly via the
L-type cross head hex wrench 6#(A). 2. Insert the tablet (mobile phone) holder
into the slot of the handlebar assembly , manually fasten the semi round head
phillipsscrews (M6×12) into holes, and lock them via the L-type cross head hex
wrench 6#(A).
L-type cross head hex wrench 6#(A)
Installation Guide
STEP 9: Pedal installation 1. Take the pedals from the package. 2. Distinguish left and right pedals. The right pedal is marked blue “R”, and the left pedal is marked red “L” (Pay attention to distinguish left and right pedals. If they are not installed correctly, crank threads will be damaged!) 3. Stand behind the seat and face the handlebar. Install the right pedal on the right crank, and ensure that the pedal is vertical to the crank mounting hole. Use an open- ended wrench (B) to lock it toward the head direction. Install the left pedal to the left crank, and ensure that the pedal is vertical to the crank mounting hole. Use an open-ended wrench (B) to lock it toward the head direction. Note: During installation, correspond the red mark on the crank to the red mark on the pedal, and the blue mark on the crank to the blue mark on the pedal. Do not mix up them!
Open-ended wrench (B)
Screw the pedal into the crank manually first, and then tighten the pedal assemblies L/R with the open-ended wrench (B). (Note: The tightening directions for both the left pedal and the right pedal are towards the head direction.)
Left pedal assembly
Note: Check whether the pedal straps are tightened before riding. Tighten them by pulling them down.
Right pedal assembly
Safety tips: Reverse riding is not recommended, as it is likely to loosen
pedals. After reverse riding, check whether the pedals are locked, in order to
avoid safety issues arising from loose pedals.
Installation Guide(for reference only, subject to the actual product)
Safety tips: Please adjust the bike according to your own conditions before
use; and tighten the bike fastening knob.
Resistance knob press it to brake in an emergency
Saddle tightening knob (Adjust the saddle horizontally) Rear column tightening
knob
(Adjust the saddle height)
+ –
Front column tightening knob (Adjust the head height)
Movable pulley
Use the provided open-ended wrench to tighten the nuts and tubes.
Bike level adjustment pad
High
Low
Statement: This manual contains the functional introduction and operating instructions as much as possible when printed. With the continuous improvement of hardware and software and optimization of design, this manual may be inconsistent with the purchased product. In case of any discrepancy in appearance, interface and color, the actual product shall prevail.
Distance Calorie Resistance Pedaling
Time
First Use
Smart knob description:
Bluetooth Touch key
Smart knob use description:
Press down to power the device on and start moving Touch button on the data
switch page
Rotate from left to right to adjust resistance
Power off
Press down to power on and enter standby status
Time page
Press down to start moving
Button switch
Button switch
Pedaling frequency page
Moving data display, and button
switch data page
Distance page
First Use
Smart knob description:
During exercise,
During exercise, press down to
rotate the knob to stop and display the exercise time,
adjust the resistance and press it again to return to exercise
Button switch
Exercise ends Press and hold for three seconds to end exercise or enter the
exercise data display page after the course finishes. Press the button
switch to check calorie and exercise mileage data.
Description of other circumstances:
Fault error and content: E01 resistance adjustment error
E02 generation system error E03 update failure
Go to the YESOUL app firmware update. Tap “Update” button.
First Use
Instructions for Use of grease lamp ring:
Each color matches with the current exercise status: Course not connected or
warm-up – the lamp ring is white; Fat burning – the lamp ring is blue; Fat
burn light ring Aerobic exercise – the lamp ring is green; Anaerobic exercise
– the lamp ring is yellow; Maximal exercise – the lamp ring is red.
Self-generating instructions: 1. When the user peddles the bike to power on
it, the spontaneous electric lamp start working, and the lamp ring enables the
courtesy lamp mode; 2. When the lamp ring is solid white, the bluetooth starts
broadcasting and enters the course. Connect to the cycling bike, and start fat
burning and fitting; 3. About the self-generation part, when the cadence is
50, power generation starts; when the cadence is <50, there is no self-
generation; 4. Bluetooth will automatically disconnect when there is no
cadence for 10 minutes.
APP installation and registration 1. Scan the QR code on the bike to download
the APP and register the APP account; 2. Upon registration, open the bike
course in the APP. Please connect the bike according to the interface prompts
in the course for the first use. Then, once you ride the bike, the exercise
mode of the APP will be enabled or the course will be automatically
accessible; 3. Before connecting the APP with bike, make sure that the
Bluetooth of your mobile phone/tablet PC has been enabled and no other devices
are connected.
cAfter the first connection, the APP will automatically match the bike.
Directly ride the bike when it is used for the second time. cThe bike does not
support the simultaneous connection of multiple mobile phones. Before using
this product, make sure that other users are not connected to the bike. cThe
bike will be disconnected 10 min after riding. cIn addition to connection with
YESOUL APP, the Bluetooth can also be connected with kinomap and zwift
software.
*Due to software upgrades, the actual product will prevail.
How to Adjust Bike
1 .Handlebar height adjustment: Rotate the front column knob in the left
direction for 4-5 turns using one hand, pull it out and hold it, hold and lift
up (or press down) the handlebar using another hand to the desired position,
then release the knob, gently pull the column up and down, so that the spring
can automatically reset (the “click” sound indicates that the knob has slipped
into the column slot hole), and then turn the knob to the right direction to
the tightest position.
Tight (Right)
Loose
(Left)
Pull
The saddle must not exceed the STOP mark during handlebar adjustment.
*Note: Before locking, please make sure to align the holes and do not exceed the STOP line.
2. Saddle height adjustment:
Rotate the front column knob in the left direction for 4-5 turns using one
hand, pull it out and hold it, hold and lift up (or press down) the seat using
another hand to the desired position, then release the knob, gently pull the
column up and down, so that the spring can automatically reset (the “click”
sound indicates that the knob has slipped into the column slot hole), and then
turn the knob to the right direction to the tightest position.
The saddle must not exceed the STOP mark during saddle adjustment.
Loose (Left)
Pull
Tight (Right)
*Note: Before locking, please make sure to align the holes and do not exceed the STOP line.
How to Adjust Bike
3.Horizontal adjustment of saddle: Loosen the handle under the saddle, slide
the saddle back and forth to the desired position, and tighten the knob as
much as possible.
Horizontal adjustment of saddle
Loose (Left)
Tight (Right)
4.Bike level adjustment:
There are four adjustment pads at the bottom of the front and rear pedal
tubes. Screw these pads until they are tightly secured on the floor and the
bike does not shake.
High
Low
How to Adjust Bike
5.Emergency brake adjustment: When braking in an emergency or stopping
movement, press the knob all the way down until it stops.
How to Determine Correct Riding Posture
1. Setup of correct saddle position
Saddle height Put the feet together, stand on one side of the saddle and
adjust the saddle to the hip height (Fig. 1). Then site on the saddle, and
step on the pedals forcibly until they are stopped at 6 o’clock and the leg
can be fully stretched (Fig. 2).
(Fig. 1)
(Fig. 2)
Horizontal position of saddle Put the right foot into the clamp, and step on the pedals, until the right pedal is at 3 o’clock and the front side of the knee joint is on the same vertical line as the pedal, that is, the saddle is in the correct position (Fig. 3).
3 o’clock: the right crank is parallel to floor
in the right direction
(Fig. 3)
How to Determine Correct Riding Posture
2. Setup of appropriate handlebar height
Each user can set up the appropriate handlebar height based on his or her body
height and riding experience. Recommendation: The handlebar should be slightly
higher than the saddle for new users (Fig. 1) and flush with or slightly lower
than the saddle for experienced users (Fig. 2). Users subject to lumbar muscle
strain and lumbar spondylosis may ride the bike with the consent of doctors.
It is recommended to adjust the handlebar into a higher position. Press down
the armrest to raise the foot tube by more than 25 °, and use the moving
pulley to drag the dynamic bicycle(Fig. 3).
(Fig. 1)
(Fig. 2)
25°
(Fig. 3)
3. Handle position layout of bike
During riding, coaches will show the corresponding hand positions, i.e. the
corresponding parts of the handlebar, as shown below.
1 Hand position 1 2 Hand position 2 3 Hand position 3 4 Hand position 4
3
2
4
1 1
4 3
2
Seat cushion angle adjustment
1.Seat cushion angle adjustment Slightly loosen two nuts (fig. 1) on the left
and right at the bottom of the seat cushion via the open-ended wrench (B), and
press the front part of the seat cushion to a comfortable angle(it is
recommended to adjust the seat cushion until its front part is one division
lower), Then tighten the two nuts at the bottom.
Open-ended wrench(B)
(Fig. 1)
Recommendation: he seat cushion may be lowered slightly in case of any hip
discomfort during riding.
(Fig. 2)
148*210mm 80g 11
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>