SONY XAV-AX8150 AV Receiver Instruction Manual

: June 3, 2024
: Sony

SONY XAV-AX8150 AV Receiver Instruction Manual

Warning
For safety, be sure to install this unit in the dashboard of the car as the rear side of the unit becomes hot during use. For details, see “Connection/Installation” (page 10).

Made in Thailand
The nameplate indicating operating voltage, etc., is located on the bottom of the chassis.
The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area) and Switzerland. The validity of the UKCA marking is restricted to only those countries where it is legally enforced, mainly in the UK.

WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Notice for customers: the following information is only applicable to equipment sold in countries applying EU directives and/ or UK applying relevant statutory requirements This product has been manufactured by or on behalf of Sony Corporation. EU Importer: Sony Europe B.V. Inquiries to the EU Importer or related to product compliance in Europe should be sent to the manufacturer’s authorized representative, Sony Belgium, bijkantoor van Sony Europe B.V., Da Vincilaan 7-D1, 1930 Zaventem, Belgium.
Hereby, Sony Corporation declares that this equipment is in compliance with Directive 2014/53/ EU. The full text of the EU declaration of conformity is available at the following internet address: https://compliance.sony.eu Hereby, Sony Corporation declares that this equipment is in compliance with the UK relevant statutory requirements. The full text of the declaration of conformity is available at the following internet address: https://compliance.sony.co.uk

Disposal of waste batteries and electrical and electronic
equipment (applicable in the European Union and other countries with separate collection systems) This symbol on the product, the battery or on the packaging indicates that the product and the battery shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbol for lead (Pb) is added if the battery contains more than 0.004% lead. By ensuring that these products and batteries are disposed of correctly, you will help to prevent potentially negative consequences for the environment and human health which could be caused by inappropriate waste handling. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery and the electrical and electronic equipment will be treated properly, hand over these products at end-of-life to the appropriate collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the appropriate collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product or battery.

Warning if your car’s ignition has no ACC position Do not install this unit in a car that has no ACC position. The display of the unit does not turn off even after turning the ignition off, and this causes battery drain.

Disclaimer regarding services offered by third parties Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations.

Important notice

Caution IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWNTIME, AND PURCHASER’S TIME RELATED TO OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE.
Dear customer, this product includes a radio transmitter. According to UNECE Regulation no. 10, a vehicle manufacturers may impose specific conditions for installation of radio transmitters into vehicles. Please check your vehicle operation manual or contact the manufacturer of your vehicle or your vehicle dealer, before you install this product into your vehicle.

Emergency calls This BLUETOOTH car handsfree and the electronic device connected to the handsfree operate using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions. Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies).

On BLUETOOTH communication

Microwaves emitting from a BLUETOOTH device may affect the operation of electronic medical devices. Turn off this unit and other BLUETOOTH devices in the following locations, as it may cause an accident. where inflammable gas is present, in a hospital, train, airplane, or petrol station near automatic doors or a fire alarm
This unit supports security capabilities that comply with the BLUETOOTH standard to provide a secure connection when the BLUETOOTH wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using BLUETOOTH wireless technology.
We do not take any responsibility for the leakage of information during BLUETOOTH communication.
If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.

Guide to Parts and Controls

Main Unit

SONY XAV-AX8150 AV Receiver Instruction Manual - Main
Unit

The VOL (volume) + button has a tactile dot.

Display/touch screen
HOME Displays the HOME screen (page 5).
STANDBY Press and hold to turn the unit to standby mode (USB charging is still available). To resume, press any button.
VOL (volume) +/
ATT (attenuate) Attenuates the sound. To cancel, press again, or press VOL +.
MONITOR OFF Press and hold to turn off the monitor. To turn back on, touch any part of the display.
Receptor for the remote commander
OPTION Displays the OPTION screen (page 5).
/ (previous/next) Functions differently depending on the selected source: [Radio]/[DAB+]: select a preset station. [USB]/[Bluetooth]: move to the previous/next file. Press and hold to: [Radio]: tune into a station automatically (SEEK+/SEEK). [DAB+]: select a station (when [Seek By] is set to [A-Z])/search for a station (when [Seek By] is set to [Station Gp]). [USB]/[Bluetooth]: fast-reverse/fast-forward.
VOICE Activates the voice command function for Apple CarPlay and Android Auto™.
HDMI terminal (input)

Screen Displays

SONY XAV-AX8150 AV Receiver Instruction Manual - Screen
Displays

Basic Operations

Pairing with a BLUETOOTH Device

When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other.

Press HOME, then touch [Settings] [Bluetooth] [Bluetooth Connection] [ON] [Pairing]. flashes while the unit is in pairing standby mode.
Perform pairing on the BLUETOOTH device so it detects this unit.
Select your model name shown on the display of the BLUETOOTH device*. When pairing is made, stays lit.

If passkey input is required on the BLUETOOTH device, input [0000].

Connecting Rear View Camera

By connecting the optional rear view camera to the CAMERA IN terminal, you can display the picture from the rear view camera. For details, see “Connection/Installation” (page 10).
To display the picture from the rear view camera Press HOME, then touch [Rear Camera].

Cancelling the Demonstration Mode

Press HOME, then touch [Settings].
Touch [General], then touch [Demo] to set to [OFF].
To exit the setup menu, touch (back) twice.

Updating the Firmware

To update the firmware, visit the support site, then follow the online instructions. URL: https://www.sony.eu/support
Note During the update, do not remove the USB device.

Additional Information

Precautions

Power antenna (aerial) extends automatically.
When you transfer ownership or dispose of your car with the unit installed, initialize all the settings to the factory settings by performing the factory reset.
Do not splash liquid onto the unit.
Notes on safety
Comply with your local traffic rules, laws, and regulations.
While driving
Do not watch or operate the unit, as it may lead to distraction and cause an accident. Park your car in a safe place to watch or operate the unit.
Do not use the setup feature or any other function which could divert your attention from the road.
When backing up your car, be sure to look back and watch the surroundings carefully for your safety even if the rear view camera is connected. Do not depend on the rear view camera exclusively.
While operating Do not insert your hands, fingers, or foreign objects into the unit as it may cause injury or damage to the unit. Keep small articles out of the reach of children. Be sure to fasten seatbelts to avoid injury in the event of sudden movement of the car.

Preventing an accident
Pictures appear only after you park the car and set the parking brake. If the car starts moving during video playback, the following caution is displayed and you cannot watch the video.
[Video blocked for your safety.] Do not operate the unit or watch the monitor while driving.

Notes on LCD panel

Do not get the LCD panel wet or expose it to liquids. This may cause a malfunction.
Do not press down hard on the LCD panel as doing so can distort the picture or cause a malfunction (i.e., the picture may become unclear or the LCD panel may be damaged).
Do not touch the panel with objects other than with your finger as it may damage or break the LCD panel.
Clean the LCD panel with a dry soft cloth. Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray.
Do not use the unit outside the temperature range 0 ºC to 40 ºC (32 ºF to 104 ºF).
If your car was parked in a cold or hot place, the picture may not be clear. However, the monitor is not damaged and the picture will become clear after the temperature in your car becomes normal.
Some stationary blue, red, or green dots may appear on the monitor. These are called “bright spots” and can happen with any LCD. The LCD panel is precision-manufactured with more than 99.99% of its segments functional. However, it is possible that a small percentage (typically 0.01%) of the segments may not light up properly. This will not, however, interfere with your viewing.

Notes on the touch screen

This unit uses a resistive touch screen. Touch the screen directly with your fingertip.
Multi-touch operation is not supported on this unit.
Do not touch the screen with sharp objects such as a needle, pen, or fingernail. Operation with a stylus is not supported on this unit.
Do not let any objects contact the touch screen. If the screen is touched by an object other than your fingertip, the unit may not respond correctly
Since glass material is used for the screen, do not subject the unit to strong shock. If cracking or chipping occurs on the screen, do not touch the damaged part as it may cause injury.
Keep other electrical devices away from the touch screen. They may cause the touch screen to malfunction.

About iPhone

Compatible iPhone models: iPhone SE (2nd generation), iPhone 11 Pro Max, iPhone 11 Pro, iPhone 11, iPhone XS Max, iPhone XS, iPhone XR, iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s
Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with an Apple product may affect wireless performance.

Notice on license

This product contains software that Sony uses under a licensing agreement with the owner of its copyright. We are obligated to announce the contents of the agreement to customers under requirement by the owner of copyright for the software. For details on software licenses, select [Settings] [General] [Open Source Licenses].
If you have any questions or problems concerning your unit that are not covered in this Operating Instructions, consult your nearest Sony dealer.

Specifications

Monitor section
Display type: Wide LCD color monitor Dimensions: 22.7 cm/ 8.95 in System: TFT active matrix Number of pixels:
1,152,000 pixels (800 × 3 (RGB) × 480) Color system:
PAL/NTSC automatic select for CAMERA IN terminal
Radio section
DAB/DAB+ Tuning range: 174.928 MHz 239.200 MHz Antenna (aerial) terminal:
External antenna (aerial) connector
FM Tuning range: 87.5 MHz 108.0 MHz Usable sensitivity: 7 dBf Signal-to- noise ratio: 70 dB (mono) Separation at 1 kHz: 45 dB
AM Tuning range: 531 kHz 1,602 kHz Sensitivity: 32 V
USB player section
Interface: USB port: USB (Hi-speed)
Maximum current: 1.5 A
HDMI section*
Input format: 480p, 576p, 720p

HDMI output is not available.
Wireless communication
Communication System: BLUETOOTH Standard version 3.0
Output: BLUETOOTH Standard Power Class 2 (Max. Conducted +1 dBm)
Maximum communication range*1: Line of sight approx. 10 m (33 ft)
Frequency band: 2.4 GHz band (2.4000 GHz 2.4835 GHz)
Modulation method: FHSS

Compatible BLUETOOTH Profiles2: A2DP (Advanced Audio Distribution Profile) 1.3 AVRCP (Audio Video Remote Control Profile) 1.3 HFP (Handsfree Profile) 1.6 PBAP (Phone Book Access Profile) 1.1
Corresponding codec: SBC, AAC
1 The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity, antenna (aerial) performance, operating system, software application, etc.
*2 BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices.

Power amplifier section
Outputs: Speaker outputs Speaker impedance: 4 8 Maximum power output: 55 W × 4 (at 4 )

General
Power requirements: 12 V DC car battery (negative ground (earth))
Rated current consumption: 10 A Dimensions (maximum):
Approx. 229 mm × 136 mm × 253 mm (9 1/8 in × 5 3/8 in × 10 in) (w/h/d)
Mounting dimensions: Approx. 182 mm × 53 mm × 160 mm (7 1/4 in × 2 1/8 in × 6 3/8 in) (w/h/d)
Mass: Approx. 2.4 kg (5 lb 5 oz) Package contents:
Main unit (1) Parts for installation and connections (1 set)
Ask the dealer for detailed information.
Design and specifications are subject to change without notice.

Copyrights

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners.
Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.
Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. Apple CarPlay is a trademark of Apple Inc.
Android Auto is a trademark of Google LLC.
WebLink is a registered trademark of Abalta Technologies, Inc. in the U.S. and a trademark in the other countries.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
All other trademarks are trademarks of their respective owners.

Connection/Installation

Cautions

Do not install this unit in a car that has no ACC position. The display of the unit does not turn off even after turning the ignition off, and this causes battery drain.
Run all ground (earth) leads to a common ground (earth) point.
Do not get the leads trapped under a screw or caught in moving parts (e.g., seat railing).
Before making connections, turn the car ignition off to avoid short circuits.
Connect the power supply leads to the unit and speakers before connecting it to the auxiliary power connector.
Be sure to insulate any loose unconnected leads with electrical tape for safety.
Choose the installation location carefully so that the unit will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and secure installation.
Be sure to use the supplied USB extension cables.
This unit may not be installed properly depending on the car type. For details on the mounting space, see “Ensuring the mounting location of the unit” (page 10).
To avoid injury, be careful not to drop the display during installation.
When installing, be careful not to cut off your fingers with the metal parts of the brackets and mounting base.
Do not pinch your fingers when attaching the display to the unit.
Do not install the unit in a position where the unit interferes with driving operations (such as in positions where the shift lever hits the unit, or the hazard button cannot be pressed).
When using the unit for a long period of time, there may be a possibility that the screws securing the display may come loose. Periodically tighten these screws.
Do not make any changes or modifications to the unit other than those described in this manual.

Note on the power supply lead (yellow) When connecting this unit in combination with other stereo components, the amperage rating of the car circuit to which the unit is connected must be higher than the sum of each component’s fuse amperage rating.

Note on installing in cars with a start-stop system The unit may restart when starting the engine from start stop. In this case, turn off the start-stop system of your car.

Note on installing in cars with electric parking brake system For cars with electric parking brakes, some related functions (such as video blocking function) may not work properly.
Mounting angle adjustment Adjust the mounting angle to less than 30°.

Ensuring the mounting location of the unit

Before installing the unit, consult the installer for details on the installation of the unit and the display.

Make sure that the distance from the front surface (reference surface) of the mounted unit to the surface of your car’s center cluster is within 22 mm (7/8 in). If exceeded, the unit cannot be installed properly.

SONY XAV-AX8150 AV Receiver Instruction Manual - Ensuring the mounting
location of the unit

Parts List for Installation

This parts list does not include all the package contents.
The mounting sleeve is attached to the unit before shipping. Before mounting the unit, use the release keys to remove the mounting sleeve from the unit. For details, see ” Removing the trim ring and the mounting sleeve” (page 15).
Keep the release keys for future use as they are also necessary if you remove the unit from your car.

Connection

To prevent short circuits, insulate leads with a cover or tape.
Note that the unit may be damaged if it is connected incorrectly or by short circuits.

SONY XAV-AX8150 AV Receiver Instruction Manual -
Connection

Not supplied
Speaker impedance: 4 to 8 × 4
RCA pin cord (not supplied)
Depending on the type of car, use an adaptor for a wired remote control (not supplied). For details on using the wired remote control, see “Using the wired remote control” (page 14).
Depending on the type of car, use an adaptor (not supplied) if the antenna (aerial) connector does not fit.
Whether in use or not, route the microphone input cord so it does not interfere with driving operations. Secure the cord with a clamp, etc., if it is installed around your feet.
For details on installing the microphone, see “Installing the microphone” (page 14).
1. Set [Antenna Power] to [ON] (default) or [OFF] depending on the type of DAB antenna (aerial) (not supplied). Max. supply current 0.1 A

Making connections

If you have a power antenna (aerial) without a relay box, connecting this unit with the power supply leads may damage the antenna (aerial).

To the car’s speaker connector

To the car’s power connector

To the parking brake switch lead
The mounting position of the parking brake switch lead depends on your car. Be sure to connect the parking brake lead (light green) of the power supply leads to the parking brake switch lead.

Memory hold connection
When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Speaker connection

Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 , and with adequate power handling capacities to avoid damage.

Power connection diagram

Check your car’s auxiliary power connector, and match the connections of leads correctly depending on the car.
SONY XAV-AX8150 AV Receiver Instruction Manual - Power connection
diagram

Installing the microphone

To capture your voice during handsfree calling, you need to install the microphone .

Cautions

It is extremely dangerous if the cord becomes wound around the steering column or gearstick. Be sure to keep it and other parts from interfering with your driving operations.
If airbags or any other shock-absorbing equipment are in your car, contact the store where you purchased this unit or the car dealer before installation.

Notes

When mounting on the dashboard, remove the visor clip carefully from the microphone , then attach the flat mount base to the microphone .
Before attaching the double-sided tape , clean the surface of the dashboard with a dry cloth.

Using the wired remote control

To enable the wired remote control, set [Steering Control] in [General] to [Preset].

Using the rear view camera

Installation of the rear view camera (not supplied) is required before use. The picture from a rear view camera connected to the CAMERA IN terminal is displayed when: the back lamp of your car lights up (or the shift lever is set to the R (reverse) position). you press HOME, then touch [Rear Camera].

Installation

To install the unit and the display securely, be sure to follow the steps to in order.

Removing the trim ring and the mounting sleeve (page 15)
Before mounting the unit (page 15)
Mounting the unit in the dashboard (page 16)
Attaching the joint cover (page 16)
Setting up the display (page 16)
Making sure the mounting positions of the display (page 18)
Organizing the USB cable (page 18)
Attaching the display to the unit (page 18)

For your safety
After mounting the display to the unit, make sure that the display does not interfere with normal driving operations such as blocking the driver’s view or getting the cables tangled.

Removing the trim ring and the mounting sleeve
Before installing the unit, remove the trim ring and the mounting sleeve from the unit.

Pinch both edges of the trim ring , then pull it out.
Insert both release keys until they click, and pull down the mounting sleeve , then pull up the unit to separate.

(2) Before mounting the unit
Before mounting the unit in the dashboard, arrange the USB extension cables.

USB cable connection diagram

Remove the cable cover, store the USB extension cable (short) to the groove of the unit, then attach the cable cover.
Position the USB cable so that its connector (male) comes to the front side of the unit.
Route the USB extension cable (long) inside the dashboard, then connect the USB cable (short) from the unit. Position the USB cable so that its connector (male) comes out from the center console panel.

(3) Mounting the unit in the dashboard

Using the mounting brackets supplied with your car You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer.

Example

Note To prevent malfunction, install only with the mounting screws .

(4) Attaching the joint cover

Attach the joint cover to the mounting base of the unit, then slide it into the unit temporarily.

(5) Setting up the display
The mounting positions of the display can be adjusted.

Adjusting the depth of the display position

Loosen the 3 pre-installed screws for depth adjustment (on top and both sides).
Slightly loosen the screws until you can slide the connector bracket. Do not remove the screws from the bracket. Doing so may damage the parts.
Slide the connector bracket to decide the appropriate depth position. Adjustable depth: within 20 mm (13/16 in) (), in 3 steps, in 10 mm (13/32 in) pitch ().
Bracket positions 1 to 3 for the display:
1: Slide-out position
2: Intermediate position
3: Slide-in position
At the desired position, tighten the 3 screws firmly to secure the connector bracket.

Adjusting the height of the display position

SONY XAV-AX8150 AV Receiver Instruction Manual - Adjusting the height of the
display position

Adjusting the display angle (tilt)

SONY XAV-AX8150 AV Receiver Instruction Manual - Adjusting the display
angle

(6) Making sure the mounting positions of the display
Be careful not to pinch your fingers or scratch the center cluster panel of your car when attaching the display to the unit.

Attach the display to the unit temporarily.
Confirm that the display does not block the driver’s view or interfere with normal driving operations. If further adjustment of the mounting position (depth, height, angle) is necessary, remove the display from the unit, then adjust it again accordingly.

(7) Organizing the USB cable

Connect the USB extension cable (short) to the USB port of the display, then route the cable along the groove.

To prevent the extension cable from coming off, be sure to route the USB cable along the groove through the catches inside.

(8) Attaching the display to the unit
Be careful not to pinch your fingers or scratch the center cluster panel of your car when attaching the display to the unit.

Attach the display to the unit.

Fuse replacement

When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.

Hereby, Sony Corporation declares that this equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://compliance.sony.eu

Register your product online now at: https://www.sony.eu/mysony