BC H7 Robot Vacuum with Self Emptying Station Robot Vacuum and Mop Combo Instructions

BC H7 Robot Vacuum with Self Emptying Station Robot Vacuum and Mop Combo Instructions

Please Scan the QR code on the right to download the”Smart Life” APP.

IMPORTANT SAFETY INSTRUCTION

WARNING

WARNING: TO REDUCE THE RISK OF INJURY OR DAMAGE, PLEASE READ THE FOLLOWING SAFETY PRECAUTIONS WHEN SETTING UP, USING, AND MAINTAINING YOUR ROBOT.
THIS APPLIANCE IS NOT INTENDED FOR USE BY CHILDREN YOUNGER THAN 8 YEARS OLD OR BY PERSONS WITH REDUCED PHYSICAL, SENSORY, OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION ON HOW TO USE THE APPLIANCE SAFELY AND UNDERSTAND THE HAZARDS INVOLVED. DO NOT ALLOW CHILDREN TO PLAY WITH THE APPLIANCE.
DO NOT ALLOW CHILDREN TO CLEAN OR SERVICE THE APPLIANCE WITHOUT SUPERVISION.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE YOUR ROBOT’S ELECTRONICS OR THE INTEGRATED DOCK-CHARGER KNOWN AS THE HOME BASE. THERE IS NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALI- FIED SERVICE PERSONNEL. DO NOT HANDLE YOUR ROBOT AND CHARGE BASE WITH WET HANDS.

Only service personnel who have been professionally trained and have obtained may service the sweeper.
If your sweeper is abnormal, refer to the Common Fault Analysis and Elimination and email us.
([email protected])

IMPORTANT SAFETY INSTRUCTION (CONT.)

• WARNING: Risk of electric shock, use indoors in dry locations only.
• Your robot is not a toy. Do not sit or stand on this device. Small children and pets should be supervised when your robot is operating.
• Store and operate your robot in room temperature environments only.
• Do not use this device to pick up sharp objects, glass, or anything that is burning or smoking.
• Do not use this device to pick up spills of water, bleach, paint, other chemicals, or anything wet.
• Do not spray or pour liquids on your robot.
• Before using this device, pick up objects like clothing, loose papers, pull cords for blinds or curtains, power cords, and any fragile objects. If the device passes over a power cord and drags it, there is a chance an object could be pulled off a table or shelf.
• If the room to be cleaned has a balcony, a physical barrier should be used to prevent access to the balcony and ensure safe operation.
• Do not place anything on top of your robot.
• Be aware that the robot moves on its own. Take care when walking in the area that the robot is operating in to avoid stepping on it.
• Do not operate the robot in areas with exposed electrical sockets in the floor.
• WARNING Shock Hazard: Your robot comes with a region approved power supply cord. Do not use any other power supply cord. For replacement cords, please contact Customer Care to ensure the proper selection of a country-specific power supply cord.
• This robot is intended for dry floor use only.
• Do not use non-rechargeable batteries. Use only the rechargeable battery supplied with the product.
• If you live in an area prone to electrical storms, it is recommended that you use additional surge protection. Your robot’s Home Base should be protected with a surge protector in the event of severe electrical storms.
• Before every use, check the battery pack for any signs of damage or leakage. Do not charge damaged or leaking battery packs.
• WARNING! Chemical Exposure: If the battery pack is leaking, do not allow the liquid to come in contact with skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice. Place the battery in a sealed plastic bag and dispose of it safely according to local environmental regulations.
• The battery pack must be removed from the robot before disposal.

This symbol on the product or its packaging indicates:
Do not dispose of electrical appliances or batteries as unsorted municipal waste, use separate collection facilities. Contact your local authority for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. Please contact your local or regional authority for more information on collection, reuse, and recycling programmers.

FCC WARNING

This device is in compliance with Part 15 of the FCC Rules. Its operation is subject to the following two conditions:
This device must not cause harmful interference.
This device must accept any interference it receives, even if such interference results in undesired operation. Any changes or modifications not explicitly approved by the party responsible for compliance could revoke the user’s authority to operate the equipment.
Please take note: This equipment has been thoroughly tested and found to meet the standards for a Class B digital device, as per Part 15 of the FCC Rules. These standards are designed to offer reasonable protection against harmful interference in a residential setting. This equipment generates and uses radio frequency energy and, if not installed and used in accordance with the provided instructions, it may potentially cause interference with radio communications. However, it’s important to understand that there’s no guarantee that interference won’t occur in a specific installation.

If this equipment does indeed cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, we encourage the user to attempt to correct the interference by taking one or more of the following steps:
For more questions please contact
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and the receiver.
Plug the equipment into an outlet on a different circuit than the one to which the receiver is connected.
Seek assistance from the dealer or an experienced radio/TV technician.
This equipment is compliant with FCC radiation exposure limits specified for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Buttons Warning

1. Turn on/off
   Press and hold the “ ” Key for 3 seconds to power on: The power indicator blinks blue slowly for 4 seconds until it turns on blue, and the robot enters the standby state.
   When the robot is stationary, long press the “ ” key for 3 seconds to shut down, and the power indicator is off.
   If the robot is stationary and does not operate for more than 10 minutes, it will enter the hibernation state. In the sleep state, press any key to wake up the machine.

2. Clean up
   When turned on, press “ ” key to voice prompt “Start cleaning”. During the cleaning process, press the “ ” button and drag the robot to pause the cleaning. Tip: When the power supply is too low, the cleaning function cannot be started.

3. Automatic or manual recharge
   After the cleaning is finished, the voice prompts “cleaning is over, start recharging”, and the robot will self-charge. When the power is insufficient during cleaning, the robot will automatically recharge.

4. Add water to the water tank or clean the mop
   Press the “ ” button to pause the robot, remove the mopping module / 2-in-1 water tank, add water or clean the mop, reinstall the mopping module, and press the button again to continue working or mopping.

5. Fault status
   When the robot is abnormal, a voice prompt is generated and the power indicator blinks red quickly. For details about how to rectify the fault, see Troubleshooting.
   If no operation is performed in the fault state for 10 minutes, the robot automatically sleeps.

PACKAGE CONTENTS

ABOUT YOUR ROBOT VACUUM

(1) Robotic

(2) Self-empty station

(3) 2in1 Water Tank and removable mop

USING YOUR ROBOT VACUUM

(1) Operating

1. Remove the protective materials from the robot vacuum cleaner front and base.
   Usually is plastic film and sponge.

2. Place the automatic dust emptying base against a wall, but make sure there is clear space in the front and both sides of the base. Finally, ensure power is connect-

IMPORTANT TIPS for CHARGING

CHARGE: Please fully charge the robot vacuum cleaner before your first-time use. And please Manually align the charging contacts of the robot vacuum cleaner with those on the base.
We recommend 6 hours on a single charge.

Plugged in: (1) the indicator light of the dust container is white and always on. (2) Robot is charging: the dust collection bucket indicator light is off. Pay special attention, this time is not not energized, just the light is off. The blue light of the robot is blinking.
(3) Dust collection in: white light breathing.
(4) Abnormal condition: Indicator is orange.

(2) Indicator status description

Notes:

1. It takes up to 6 hours to reach a full charge. This will provide up to 180 minutes of cleaning time on hard floors with minimum suction power.
2. If the robot vacuum cleaner doesn’t charge, please directly email us at: [email protected].
3. To extend the battery’s lifespan, please recharge the robot at least once every 2 months if it’s not been used for a long time.

(3) APP Contraction

1. All of First， Please Scan the QR code on the right to download the “Smart Life” APP.
   To make sure the app you download is the official “Smart Life ” App, please scan our QR code to download it!
   Note: When device’s power level is less than 30%，will not connect the wifi&APP.

2. Reset WiFi
   Press “ ” and “ ” hold the “ ” and “ ” buttons until you hear the “Resetting WiFi” voice alert. The reset is complete when the WiFi indicator flashes slowly. The robot will then wait for a connection.

3. Add Device
   Open the ‘’Smart Life‘’App, tap “+” in the middle or right top and add the device as instructed in the app.
   (1) On the Add Device page, select “Home Vacuum (wifi)”
   (2) Jump to the link wifi page, enter your home WiFi password to link with your WiFi.
   (3) Jump to the link channel with the robot vacuum and ‘Confirm
   
   (4) Please choice the AP Mode only;
   (5) Ensure that AP Mode is selected, then Continue;
   (6) Jump to the machine hotspot link, find the SL-Boolean Cloud wifi to contact.

(7) Waiting patiently for the link;
(8) Successfully add your robot vacuum.

1. IMPORTANT:If you can’t connect to the wifi or device please check the following.
2. double check that you have entered your home wifi password correctly.
3. make sure you select the “AP” matching method when you choose the link method.
4. In Step 6, if the hotspot beginning with ‘SL-Boolean Cloud……’ doesn’t appear, you can refresh and wait a bit before linking.

PRECAUTIONS

REGULAR ROBOT CARE

Operating

Tip:

1. If the mop is too dirty, it will affect the mopping effect, please clean it in time.
2. Be sure to remove the mop to clean and wring out the installation. Do not install it on the two-in-one water tank for cleaning, otherwise it is easy to damage the two-in-one a tank of water.
3. It is recommended to replace the mop every 6-12 months to ensure the cleaning effect.

Cleaning roller

Tip: It is recommended to replace the side brush after 3-6 months to ensure the cleaning effect.

Dust bag replacement

When the dust bag is full, the orange light of the dust collector flashes, or the APP notifies you, please replace the dust bag in time. When the dust bag is in normal use, the white light is on.

Dust duct

If the orange light of the dust collecting station flashes after replacing the dust bag, it is recommended to unplug the power plug, reverse the dust collecting charging pile, and check whether the dust channel is blocked by foreign matter. If the dust passage is blocked, remove the transparent cover of the dust passage with a screwdriver and clean out the foreign matter by referring to the following figure.
Note: Violent disassembly is prohibited. When you’re done, put it back.

Sensors, Robot Top and Charging/Dust Collecting Contacts

Use a damp cloth to clean all sensors and the robot top once per month.

TROUBLESHOOTING

TECHNICAL SPECIFICATIONS

Suitable for American

Suitable for European

Name and content of harmful substances in the product.

This form is prepared in accordance with the provisions of SJ/T 11364-2014.

O: indicates that the content of the harmful substance in all homogeneous materials of the part is in The limit specified in GB/T 26572-2011 is below the requirements.
X: indicates that the concentration of the hazardous substance in at least one homogeneous  material of the part exceeds the limit requirements specified in GB/T 26572-2011.
(The part of ” ” indicates that the complete replacement of non- environmentally friendly substances or elements cannot be achieved due to the technical and technical limitations of the whole world, and will be gradually improved with technological improvements.)

BOOLEAN CLOUD CUSTOMER CARE

We offer year-round, 12-hour-a-day customer service (8am-8pm), please contact us at [email protected] with any questions.
Our products are backed by USA domestic warranty or replacement parts, we offer 3 months unconditional return and refund policy, and one year warranty service. Please contact us if you have any questions!

For more questions please contact [email protected]

References

• 优博科技微信分销平台

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>