Gosund SLS1 WIFI Smart Light Switch User Manual
- June 16, 2024
- gosund
Table of Contents
Gosund SLS1 WIFI Smart Light Switch User Manual
Features
- Can be controlled by iOS phone/Android phone
- Support “Gosund” APP
- Voice control: Compatible with Alexa and Google home Tmall Genie or Xiaodu speakers
- Timing function: Auto on/off with timing function
- Overload protection for easy replacement of your traditional mechanical switches (needs neutral)
- Smart scene
- Device group
Security Information
Risk of electric shock: Electricity can cause personal injury and property
damage if not handled properly. If you are unsure of any part of these
instructions, seek professional help from a qualified electrician.
Product Information
- WIFI Standard: IEEE 802.11 b/g/n 2.4GHz
- Working voltage: AC 110-240VAC 50/60Hz
- Load power: 500W/Gang
- Maximum load current: 10A
- Power consumption: ≤0.5W
- Working temperature: 0℃~40℃
- Dimensions: 86x86x35mm
Install
How to open the switch glass panel
Use a flat screwdriver to pry out the slots on the top and bottom (as well as left and right) of the switch bottom shell to open it
Notice:
Make sure the power on the circuit breaker is turned off before wiring.
-
Two wiring methods:
Wiring method 1: neutral wire needs to be connected
Wiring method 2: No need to connect the neutral wire (capacitor required) -
The wire colors indicated in this manual are the usual colors and may vary in some houses.
-
Make sure the wire conductors are securely attached to each wire.
-
Make sure the Wi-Fi signal is stable and working properly before wiring.
-
If you do not have any wiring experience, please call a professional electrician.
First step:
- Turn off the circuit breaker and test the power with an electrical tester.
- Make sure the switch is off before wiring.
Second step
- Remove existing wall panels; turn on power at breaker and use electrical tester to check which wire is the line; the tester will flash or beep when near the line
- Turn off the power at the circuit breaker, if there is a power outage, use an electrical tester, pull the existing witch out; mark the wiring and other wires; disconnect the power with pliers and remove the wires from the existing switch.
- Connect the switch wires to the wall box with the wire conductors according to the wiring diagramin the wire
Two Wiring methods
-
Neutral & Live wire (Neutral wire Required)
-
Single Live wire No Neutral wire Required
Third step: Install the switch using the screws provided and snap the wall plate onto it.
The fourth step: Turn the power back on at the circuit breaker, then turn on the lights.
Wiring method 1:
Neutral & Live wire(Neutral wire Required)
The Live wire is connected to the “L” terminal,
The Neutral wire is connected to the “N” terminal,
Lighting wire is connected to “L1, L2, L3” terminals
1Gang switch lighting wire connection: “L1” terminal
2Gang switch lighting wire connection: “L1,L2” terminals
Wiring method 2:
Single Live wire(No Neutral wire Required)
The Live wire is connected to the “L” terminal,
Lighting wire is connected to “L1, L2, L3” terminals (L1 lamp needs to be
connected to a capacitor)
1Gang switch lighting wire connection: “L1” terminal
(L1 lamp needs to be connected to a capacitor)
2Gang switch lighting wire connection: “L1,L2” terminals
(L1 lamp needs to be connected to a capacitor)
Add device:
Add device to “Gosund” APP
Step 1: Download and install the “Gosund” APP:Scan the QR code below
Step 2: Enter the phone settings option, turn on the Bluetooth and WiFi functions, and turn on the product at the same time
Step 3: Open the Gosund APP, register and log in your account, if you have a Gosund account, just log in.
Step 4: Power on after the wiring is completed, the device is powered on by default, press and hold the touch wall switch button for about 8s, until the WiFi blue LED flashes quickly, enter the network configuration mode
Step 5: Enter the App, click the “+” at the top right of the page to enter the network connection page.
Step 6: Make sure your device’s light is blinking quickly (2 times per second) tap to proceed to the next step.
Step 7: Enter your WiFi and password
Step 8: Name your device.
Step 9: When the WiFi LED is on, the device is online.
Take control now!
How to use smart speakers to control devices, such as Amazon Alexa, Google
Assistant or Tmall Genie?
Open the Gosund app to enter the “Me” view and find the user guide for the corresponding smart speaker.
Note: Before using the smart speaker, please log in to your account on
Amazon Alexa,
Google Assistant, or Tmall Genie.】
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and(2) this device must
accept any interference received, including interference that may cause
undesired operation.
RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment shall be installed and operated with
minimum distance 20cm between the radiator & body.
- Hereby, Shenzhen Cuco Smart Technology Co., Ltd. declares that the radio equipment type G2 is compliant with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://cedeclaration.gosund.com/
- Frequency Range: 2400–2483.5 MHz Wi-Fi/Bluetooth Max. Transmitting Power: 20 dBm
- WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted
household waste. Instead, you should protect human health and the environment
by handing over your waste equipment to a designated collection point for the
recycling of waste electrical and electronic equipment, appointed by the
government or local authorities. Correct disposal and recycling will help
prevent potential negative consequences to the environment and human health.
Please contact the installer or local authorities for more information about
the location as well as terms and conditions of such collection points.
Contact Information:
Shenzhen Cuco Smart Technology Co., Ltd.
Address : Room 201, 301, Building A, No.12 Difu Road,
Guxing Community, Xixiang Street, Bao’an District,
Shenzhen 51800, Guangdong, P. R. China
Website: www.gosund.net
Email Support: service.eu@gosund.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>