nVent CADDY CM91216M EM-MR Conduit To Flange Clip Owner’s Manual
- June 16, 2024
- nVent Caddy
Table of Contents
nVent CADDY CM91216M EM-MR Conduit To Flange Clip
Product Information
Specifications
- Catalog Number: CM91216M
- Installation: Fast hammer-on
- Retainer Strap: Pre-riveted and easily bent into position
Features
- Easy and fast installation with only one piece
- Pre-riveted retainer strap for quick and easy positioning
WARNING:
nVent products must be installed and used according to the instructions provided by nVent. Failure to follow the instructions and warnings may result in product malfunction, property damage, serious bodily injury, or death, and may void your warranty. Please refer to the instruction sheets available at www.nvent.com or contact your nVent customer service representative for more information.
Contact Information:
- Europe Netherlands: +31 800-0200135
- France: +33 800 901 793
- Germany: 800 1890272
- Other Countries: +31 13 5835404
- APAC Shanghai: +86 21 2412 1618/19
- Sydney: +61 2 9751 8500
Brands:
Our powerful portfolio of brands includes nVent.com, CADDY, ERICO, HOFFMAN, RAYCHEM, SCHROFF, and TRACER. All trademarks mentioned belong to their respective owners.
Note: nVent reserves the right to change specifications without notice.
Product Usage Instructions
Installation
- Ensure you have the necessary tools and equipment for installation.
- Inspect the CM91216M product for any visible damage or defects.
- Identify the desired location for installation.
- Position the CM91216M in the desired location and align it properly.
- Using a hammer, firmly strike the CM91216M to secure it in place. Ensure it is tightly installed.
- Bend the pre-riveted retainer strap into the desired position to ensure proper retention.
- Double-check the installation to ensure it is secure and properly aligned.
Maintenance
To maintain the CM91216M product, regularly inspect it for any signs of damage or wear. If any issues are detected, contact nVent customer service for assistance. Do not attempt to repair or modify the product yourself as it may void your warranty.
Cleaning
To clean the CM91216M, use a soft cloth dampened with mild soap and water. Gently wipe the surface of the product to remove any dirt or debris. Avoid using abrasive cleaners or solvents as they may damage the product.
Disposal
When disposing of the CM91216M, follow local regulations and guidelines. Do not dispose of it in regular household waste.Contact your local waste management facility for proper disposal methods.
FAQ
- Q: Can I install the CM91216M without using a hammer?
- A: No, the CM91216M requires hammer-on installation for proper and secure attachment.
- Q: How do I know if the CM91216M is securely installed?
- A: After hammering the CM91216M into place, ensure it is tightly secured and does not move or shift when pressure is applied.
- Q: Can I modify the pre-riveted retainer strap?
- A: Yes, the pre-riveted retainer strap can be bent into the desired position to ensure proper retention. However, avoid excessive bending or sharp angles that may compromise its effectiveness.
- Q: What should I do if I notice damage or defects on the CM91216M?
- A: If you notice any visible damage or defects on the CM91216M, contact nVent customer service for further assistance before proceeding with installation.
FEATURES
- Only one piece to install
- Fast hammer-on installation
- Pre-riveted retainer strap is easily bent into position
PRODUCT ATTRIBUTES
- Material: Spring Steel
- Finish: nVent CADDY Armour
- EMT Conduit Size : 3/4″;1″
- Rigid Conduit/Pipe Size: 3/4″;1″
- Outer Diameter : 0.922″ – 1.378″
- Flange Thickness: 9/16″ – 3/4″
- Static Load: 75 lb
WARNING
nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication, or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury, and death, and/or void your warranty
CONTACT
North America
- +1.800.753.9221
- Option 1 – Customer Care
- Option 2 – Technical Support
Europe
- Netherlands:
- +31 800-0200135
- France:
- +33 800 901 793
Europe
- Germany:
- 800 1890272
- Other Countries:
- +31 13 5835404
APAC
- Shanghai:
- + 86 21 2412 1618/19
- Sydney:
- +61 2 9751 8500
© 2023 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice.
References
- Building a more Sustainable and Electrified World | nVent
- Building a more Sustainable and Electrified World | nVent