nVent CADDY CRLJ37EG Rod Lock Bar Joist Hanger Rod Owner’s Manual

nVent CADDY CRLJ37EG Rod Lock Bar Joist Hanger Rod

Product Information

Specifications

• Catalog Number: CRLJ37EG
• Product Type: Rod Lock Bar Joist Hanger
• Rod Size: 3/8 inch

Features

• Wrench Size 1: Hex nut size used to tighten to bar joist
• Wrench Size 2: nVent CADDY Rod Lock hex nut size

Additional Product Details
nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication, or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury, and death and/or void your warranty.

Contact Information
If you have any questions or need assistance, please contact nVent customer service representatives in the following regions:

• Europe Netherlands: +31 800-0200135
• France: +33 800 901 793
• Germany: 800 1890272
• Other Countries: +31 13 5835404
• APAC Shanghai: +86 21 2412 1618/19
• Sydney: +61 2 9751 8500

Brands
Our powerful portfolio of brands includes:

• nVent
• CADDY
• ERICO
• HOFFMAN
• RAYCHEM
• SCHROFF
• TRACER

Disclaimer
nVent reserves the right to change specifications without notice.

Product Usage Instructions

Step 1: Preparing the Installation Area
Prior to installation, ensure that the bar joist is clean and free from any debris or obstructions.

Step 2: Placing the Rod Lock Bar Joist Hanger
Position the Rod Lock Bar Joist Hanger on the bar joist, aligning it with the desired location. Make sure the wrench size 1 hex nut is facing towards the bar joist.

Step 3: Tightening the Rod Lock Hex Nut
Using a wrench of appropriate size, tighten the wrench size 1 hex nut to securely fasten the Rod Lock Bar Joist Hanger to the bar joist.

Step 4: Final Check
Double-check that the Rod Lock Bar Joist Hanger is securely attached to the bar joist before proceeding with further installation or usage.

Warning
Always follow nVent’s product instruction sheets and training materials to ensure proper installation and usage. Failure to do so may result in product malfunction, property damage, serious bodily injury, and voiding of warranty.

NVENT CADDY ROD LOCK BAR JOIST HANGER, 3/8″ ROD

CATALOG NUMBER
CRLJ37EG

FEATURES

• Easily installs from underneath the bar joist
• Easily installs on lower or upper truss chord of the bar joist
• Plastic protection cap prevents dirt or structural coatings from obstructing the “push-to-install” mechanism
• Prefabricated assemblies easily lift and lock into place, helping to save time and money
• Easy “push-to-install” design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position
• Works with slightly damaged threads and minor burrs on the threaded rod

PRODUCT ATTRIBUTES

• Material: Steel
• Finish: Electrogalvanized
• Static Load Safety Factor: 3.5:1
• Rod Size: 3/8″
• Height: 7.400″
• Width: 3.700″
• A: 5/8″ – 1 1/4″
• Wrench Size 1: 9/16″
• Wrench Size 2: 15/16″
• Static Load: 1,000 lb

ADDITIONAL PRODUCT DETAILS

Wrench Size 1 represents hex nut size used to tighten to bar joist. Wrench Size 2 represents nVent CADDY Rod Lock hex nut size.

DIAGRAMS

WARNING

nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury, and death and/or void your warranty.

Frequently Asked Questions

• Q: Where can I find nVent’s product instruction sheets?
  A: nVent’s product instruction sheets are available at www.nvent.com or you can request them from your nVent customer service representative.

• Q: What should I do if I have questions or need assistance?
  A: If you have any questions or need assistance, please contact nVent customer service representatives in your region using the provided contact information.

• Q: Can the specifications of the product change?
  A: Yes, nVent reserves the right to change specifications without notice. Please refer to the most up-to-date information available.

Contact Information

North America

• +1.800.753.9221
• Option 1 – Customer Care
• Option 2 – Technical Support

Europe

• Netherlands: +31 800-0200135
• France: +33 800 901 793

Europe

• Germany: 800 1890272
• Other Countries: +31 13 5835404

APAC

• Shanghai: + 86 21 2412 1618/19
• Sydney: +61 2 9751 8500

Our powerful portfolio of brands:
nVent.com

• CADDY
• ERICO
• HOFFMAN
• RAYCHEM
• SCHROFF
• TRACER

© 2023 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners.

nVent reserves the right to change specifications without notice.

References

• Building a more Sustainable and Electrified World | nVent
• Building a more Sustainable and Electrified World | nVent

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>