CIAYS CISGO2B1 Safety Gate Instruction Manual

SAFETY GATE
INSTRUCTION MANUAL Model:
CTSGO1/02’03/04 CISGO1/02/03 /CISGO2B1/CISGO8W/06W
Rev(03) A

COMPONENTS

Find your model to see what components are included.

WARNING

• To prevent serious injury or death, securely install the gate or enclosure and use according to manufacturer’s instructions.
• Stop using when a child can climb over, enclosure or dislodge the gate.
• This product will not necessarily prevent all accidents.
• Never leave child unattended.
• Use only with the locking mechanism securely engaged.
• Intended for use with children from 6 months through 24 months of age.
• Stop using gate if any parts are missing or become damaged.
• Children may die or be seriously injured if gates are not securely installed.
• ALWAYS install and use gates as directed using all required parts.
• Periodically check all fasteners to be sure they are tight and secure.
• Adult Assembly Required.
• The surfaces that the gate is to fixed to must be suitable for the purpose and must be structurally sound.
• Indoor use only, and not to be exposed to outdoor elements.
• Install this gate away from heaters and other sources of heat.
• STOP using when a child can climb over or dislodge the gate.

WARNING

1. To help with installation, DO NOT CUT OFF THE  CABLE TIE until the installation is completed!
2. The door gap is NOT a defect! It will be shortened to 0.08in (0.2cm) after installation.

Before installation, there will be a gap between the gate latch and the frame which is NOT a defect and it is NOT bent. This gap will disappear after installation, and then you can cut off the tightening cable tie.

Bottom of the stairs
Must be placed before the lowest stairs
Top of the stairs
Must be placed on the highest stairs and drilled for installation
If used in any scenarios below the following aspects need to be noted
Bottom of the stairs: must be placed before the lowest stairs
Top of the stairs: must be placed on the highest stairs and drilled for installation

INSTALLATION GUIDE

METHOD A:
(Follow STEP 1-2-3-4-6)
METHOD B:
(Follow STEP 1-2-3-4-5-6)

STEP 1. Measure the width of the doorways.
Following the below extension combination suggestions to install the gate and extensions.

CISGO6W

Fits 29,5-33.5in(75-85cm)

a
a+b1| 29,.5-33.5in(75-85cm)
33.5-37.4in(85-95cm)

CISGO8W

Fits 29.5-37.4in(75-95cm)

a
a+b1
a+b1+b1| 29.5-33.5in(75-85cem)
33.5-37.4in(85-95cm)
37,4-41,3in(95-105cm)

CTSGO1/CISGO1

Fits 29.5-41.3in(75-105cm)

a
a+b1
a+b2
a+b1+b2| 29,5-33,5in(75-85cm)
33.5-37.4in(85-95cm)
37,4-41.3in(95-105cm)
41.3-45.3ind105-115cm)

CTSGO2/CISGO2/CISGO2B1

Fits 29.5-45.3in(75-115cm)

a
a+b1
a+b2
a+b1+b2
a+b2+b2
a+b1+b2+b2| 29.5-33.5in(75-85cm)
33.5-37.4in(85-95cm)
37.4-41.3in(95-105cm)
41.3-45.3ind105-115cm)
45.3-49.2in(115-125cm)
49.2-53.1ind125-135cm)

CTSGO3/CISGO3

Fits 29.5-53.1in¢75-135cm)

a
a+b1
a+b2
a+b3
a+b1+b2
a+b1+b3
a+b2+b3
a+b1+b2+b3| 29.5-33.5in(75-85cm)
33.5-37.4in(85-95cm)
37.4-41.3in(95-105cm)
41.3-45.3indl05-115cm)
41.3-45.3indl05-115cm)
45.3-49.2in(15-125cm)
49.2-53.1in(125-135cm)
53.1-57.0in(135-145¢em)

CTSGO4

Fits 29,5-57in(75-145cm)

Step 2.
Insert 4 bolts into 4 corners of the gate/extension.

Expanding the gap between the rubber foot and the adjustment wheel. In order for the gate to function properly.
It is recommended that the gate gap between the gate locks is O.O8in (0.2cm).

Step 3.
Pre-assemble the gate, and locate four points for hole drilling. Hold the wall cup in position and mark the center with a pencil.Position your gate in the center of the opening on the floor. DO NOT allow a gap of more than (2 inch) 5cm between the gate and the Wall.

Step 4.
Cover the wall cup to the bolts. Tighten the wheel inward by hand, Do not over tighten.

Step 5.
Drill holes for the 4 marked positions, then put wall anchors and use screws and the wall cup.

STEP 6. OPERATING THE GATE

A. To Open the Gate

1. Cut off the cable tie and check if the gate is firmly attached.
2. Pull the button back with your thumb.
3. Lift the door panel to open in either direction.

B. To Close the Gate

NOTE:

• If the gate is too difficult to latch or latch, adjust the tightness of 4 adjustment bolts until the gate can be unlatch and latch smoothly.
• If the gate lock is too difficult to unlatch, slightly loosen the adjustment wheels.
• If the gate lock is too loose to latch, slightly tighten the adjustment wheels.

TURN ON THE  ALARM

1. Unscrew the bolt with a self-supplied Phillips screw- driver to detach the cover.
2. Put two AAA batteries into the battery compartment.
3. Reattach the cover by tightening the bolt with the Phillips screwdriver.
4. Turn on the button of the alarm, the alarm rings for 10 seconds once the gate is unlatched.

Thank you for choosing this product! We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at
Questions or Problems?
[email protected]
Latest Information and More.
@CiaysOffcial

https://www.facebook.com/CiaysOffcial

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>