V I V O STAND-LIVE1M All In One Livestream Multi-Mount Floor Stand Instruction Manual Product Information
- January 7, 2024
- V I V O
Table of Contents
- STAND-LIVE1M All In One Livestream Multi-Mount Floor Stand
- Product Information
- Specifications
- Package Contents
- Assembly Steps
- Step 1: Base Assembly
- Step 2: Pole and Arms Assembly
- Step 3: Mounting Arms and Accessories
- Step 4: Dual Arm Configuration
- Q: What is the weight capacity of the stand?
- Q: What tools are needed for assembly?
STAND-LIVE1M All In One Livestream Multi-Mount Floor Stand
Product Information
Specifications
-
Product Name: Mobile All-In-One Livestream Multi-Mount Floor
Stand -
SKU: STAND-LIVE1M
-
Weight Capacity:
- Microphone: 2.2lbs (1kg)
- Camera & Phone: 6.6lbs (3kg)
- Monitor: 11lbs (5kg)
- Laptop: 11lbs (5kg)
Package Contents
- A (x1) Adjustable Pole
- B (x1) Ring Light
- C (x1) Mic Boom
- D (x1) Laptop Tray
- E (x4) Legs
- F (x1) VESA Plate
- G (x1) Base
- H (x2) Cable Clip
- I (x2) Lower Arm
- J (x4) Upper Arm
- K (x1) Dual Connector
- L (x1) Phone/Tablet Holder
- M (x1) Mic Boom Clamp
- N (x1) Mic Mount
- O (x2) Caster
- P (x2) Locking Caster
- Q (x4) Locking Pole Ring
- R (x1) Pole Cover
- S (x2) Threaded Connector
- T (x2) Ball Head
- S-A (x3) M6x20mm Screw
- S-B (x8) M6x25mm Screw
- S-C (x4) M4x8mm Screw
- S-D (x4) M5 Washer
- M-A (x4) M4x12mm Screw
- M-B (x4) M5x12mm Screw
- M-C (x4) M5 Washer
- T-A (x1) 4mm Allen Wrench
- T-B (x1) 5mm Allen Wrench
- T-C (x1) Wrench
Assembly Steps
Step 1: Base Assembly
-
Connect Legs (E) to Base (G) using M6x25mm Screws (S-B) and 5mm
Allen Wrench (T-B). Attach Casters (O) and Locking Casters (P) to
Legs (E). -
Secure the assembled base to Adjustable Pole (A) using M6x20mm
Screws (S-A) and 4mm Allen Wrench (T-A). -
Turn the assembly over and adjust Caster (P) height using
Wrench (T-C). Use the side tab on Locking Casters (P) to lock the
wheels in place during assembly of the stand.
Step 2: Pole and Arms Assembly
-
Slide Cable Clip x2 (H), Locking Pole Ring x4 (Q), Lower Arm x2
(I), and Dual Connector (K) onto Adjustable Pole (A) following the
given order. -
Tighten the set screw of Locking Pole Ring (Q) using 4mm Allen
Wrench (T-A). -
Adjust the height of the Pole by twisting the Height Adjuster
(A1) on Pole (A) to raise or lower it. Lock into place by
tightening the set screw on Locking Pole Ring (Q) directly above
Height Adjuster (A1) using 4mm Allen Wrench (T-A).
Step 3: Mounting Arms and Accessories
-
Connect Upper Arm (J) to the right side Lower Arm (I), then
install VESA Plate (F) to Upper Arm (J). Secure by tightening set
screws using 4mm Allen Wrench (T-A). -
Attach Upper Arm (J) to the left side Lower Arm (I), and secure
by tightening set screws using 4mm Allen Wrench (T-A). Insert
Threaded Connector (S) into Upper Arm (J).
Step 4: Dual Arm Configuration
- Connect Upper Arm (J) to Dual Connector (K), then connect a
second Upper Arm (J). Install Threaded Connector (S) to Upper Arm
(J). Secure by tightening set screws using 4mm Allen Wrench
(T-A).
FAQ
Q: What is the weight capacity of the stand?
The weight capacity of the stand is as follows:
- Microphone: 2.2lbs (1kg)
- Camera & Phone: 6.6lbs (3kg)
- Monitor: 11lbs (5kg)
- Laptop: 11lbs (5kg)
Q: What tools are needed for assembly?
The following tools are needed for assembly:
- Phillips Screwdriver
- 4mm Allen Wrench (T-A)
- 5mm Allen Wrench (T-B)
- Wrench (T-C)
Mobile All-In-One Livestream Multi-Mount Floor Stand
Instruction Manual
SKU: STAND-LIVE1M
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product. https://vivo-us.com/products
/stand-live1m
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1) Adjustable
Pole
F (x1) VESA Plate
B (x1) Ring Light
C (x1) Mic Boom
D (x1) Laptop Tray
E (x4) Legs
G (x1) Base
H (x2) Cable Clip
I (x2) Lower Arm
J (x4) Upper Arm
K (x1) Dual Connector
L (x1) Phone/Tablet
Holder
P (x2) Locking Caster
Q (x4) Locking Pole
Ring
M (x1) Mic Boom
Clamp
N (x1) Mic Mount
R (x1) Pole Cover
S (x2) Threaded Connector
O (x2) Caster
T (x2) Ball Head
S-A (x3) M6x20mm
Screw
S-B (x8) M6x25mm
Screw
S-C (x4) M4x8mm
Screw
S-D (x4) M5 Washer
M-A (x4) M4x12mm
Screw
M-B (x4) M5x12mm
Screw
M-C (x4) M5 Washer
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
T-A (x1) 4mm Allen
Wrench
T-B (x1) 5mm Allen
Wrench
T-C (x1) Wrench
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED TOOLS NEEDED
2.2lbs (1kg)
MICROPHONE
6.6lbs (3kg)
CAMERA & PHONE
11lbs (5kg)
MONITOR
11lbs (5kg) LAPTOP
Phillips Screwdriver
2
ASSEMBLY STEPS
STEP 1
Connect Legs (E) to Base (G) using M6x25mm Screws (S-B) and 5mm Allen Wrench (T-B). Attach Casters (O) and Locking Casters (P) to Legs (E).
T-B
P
O
S-B
G
P
E
O
Secure assembled base to Adjustable Pole (A) using M6x20mm Screws (S-A) and
4mm Allen Wrench (T-A).
T-A
S-A
A
Turn assembly over and adjust Caster (P) height using Wrench (T-C). Use side
tab on Locking Casters (P) to lock wheels in place during assembly of stand.
T-C
P
3
STEP 2
Slide Cable Clip x2 (H), Locking Pole Ring x4 (Q), Lower
Arm x2 (I), and Dual Connector (K) onto Adjustable Pole
(A) following the order shown below.
K
Tighten set screw of Locking Pole Ring (Q) using 4mm Allen Wrench (T-A).
Height Adjustment Twise the Height Adjuster (A1) on Pole (A) to raise or lower the Pole. Lock into place by tightening the set screw on Locking Pole Ring (Q) directly above Height Adjuster (A1) using 4mm Allen Wrench (T-A).
I
A Q
Q A1 T-A
I H A
Stand can now be customized as desired with mounting arms and accessories.
The following steps give an example of how stand arms and accessories can be
mounted.
CAUTION : Properly balance the left and right weight distribution of the arms
to prevent tipping.
4
STEP 3
F J
Connect Upper Arm (J) to right side Lower Arm (I), then install VESA Plate (F)
to Upper Arm (J). Secure by tightening set screws using 4mm Allen Wrench
(T-A).
T-A
I
STEP 4
Attach Upper Arm (J) to left side Lower Arm (I), and secure by tightening set
screws using 4mm Allen Wrench (T-A). Insert Threaded Connector (S) into Upper
Arm (J).
S J
T-A I
5
STEP 5
Connect Upper Arm (J) to Dual Connector (K), then connect a second Upper Arm
(J), as shown below. Install Threaded Connector (S) to Upper Arm (J).Secure by
tightening set screws using 4mm Allen Wrench (T-A).
S
J T-A
J K
STEP 6
Screw Ball Head (T) onto Threaded Connector (S), then screw Ring Light (B)
onto Connector.
B T
S J
6
STEP 7
Connect Mic Boom (C) to remaining mounting hole in Dual Connector (K). Twist
Mic Mount (N) onto Mic Boom (C). Optional: Mic Boom (C) can be desk mounted
using Mic Boom Clamp (M).
N If needed, install the 5/8″ Adapter, as shown.
C
C M
C K T-A
7
STEP 8
For VESA Plate (F), choose between Monitor or Laptop Holder.
Monitor: Attach Screws (M-A or M-B) and M5 Washers (M-C) in the top VESA holes
on monitor, using a Phillips screwdriver. Slide onto VESA Plate (F) and attach
remaining two Screws (M-A or M-B) and M5 Washers (M-C).
Laptop: Attach M4x8mm Screws (S-C) and M5 Washer (S-D) into Laptop Tray,
partially protruding, using Phillips screwdriver. Slide onto VESA Plate (F)
and attach remaining M4x8mm Screws (S-C) and M5 Washers (S-D).
S-C S-D
F
D
S-C S-D
8
Optional
VESA Plate (F) can be adjusted using 4mm Allen Wrench (T-A) to allow monitor
to tilt, turn, and swivel.
T-A
STEP 9
Twist Ball Head (T) onto Threaded Connector (S), then connect Phone/Tablet
Holder (L). NOTE: Ball Head (T) can also be used to mount cameras, and other
multi-media devices.
L
T
T
S
S
9
STEP 10
Remove bottom covers from Lower Arms (I) and Upper Arms (J) by sliding off.
Organize cables and slide covers back on.
J J
J I
J I
10
THIS PAGE INTENTIONALLY LEFT BLANK 11
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
LAST UPDATED: 11/09/2022 REV2
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Mobile All-In-One Livestream Multi-Mount Floor Stand – VIVO - desk solutions, screen mounting, and more