tecno switch SE336AN Mini Infrared Motion Sensor Instructions

tecno switch SE336AN Mini Infrared Motion Sensor

IN CONFORMl1YWITH NORMATIVE
2014/30/UE, 2014/35/UE, EN55015, EN61000-3-2, EN61000-3-3, EN61547, EN61058-1

SPECIFICATION

• Power supply : 230 Vac, 50-60 Hz
• Rated load : Incandescent 800 W, Fluorescence 200 W, LED 180 W
• Operating temperature : from -15 to +40°C
• Detection distance : 3 – 6 m selectable
• Time delay : 5 sec. / 30 sec. / 1 min. / 3 min. / 5 min. / 8 min.
• Lux adjusting : 5 / 2000 LUX selectable
• Installing height : wall from 1.8 to 2.5 m; ceiling from 2,2 to 4 m

Installation tips

1. Infrared is activated by lights, heat sources, movements of objects, transit of people and medium / large sized animals, etc.
2. Never point the sensor towards light or heat sources such as air conditioning.
3. Avoid pointing the sensor to objects that tend to move.
4. It is recommended to mount the sensor sheltered from wind and rain.
5. Combine a contactor with our sensors, if connected to inductive loads (fluorescence).

Installation

The installation must be performed by qualified personnel, always after carefully reading the instructions.

1. Disconnect the power supply.
2. Make the electrical connections following the diagram. (Fig.1)
3. Install the sensor in the desired position using screws and dowels. (Fig.2)
4. Restore power.
5. Set the sensor operation using the DIP switch (Fig.3):
6. Time delay selects one of the intervention times;
7. Night/24 hours selects the sensor activation brightness threshold, 5 or 2000 lux;
8. Sens adjust selects the sensing distance between minimum and maximum.

Useful tips for malfunctions

• The lamps do not light up
  • Check lux adjustment and connected lamps. Turn off the power for at least 10 seconds
• The lamps do not go out
  • Check the set time. Turn off the power for at least 10 seconds.
• The lamps continue to turn on and off
  • The sensor is installed too close to heat sources.
  • The sensor is oriented directly towards reflective surfaces or light sources.
• Decreased sensitivity
  • Check the installation height.
  • Very high or particularly cold ambient temperature.
  • Dust on the lens, clean it with a damp cloth.

**Illustrative summary of main features

**

• Pursuant to Legislative Decree No. 49 of 14 March 2014
• Implementation of Directive 2012/19AJE on waste electrical and electronic equipment (WEEE)”
• The symbol of the crossed bin, placing it on the appliance, also indicates that the pre-batch at the end of its useful life must be collected separately from other waste.
• The user will therefore have to deliver the integrated equipment of the as9911Zial components that has reached the end of its life to the appropriate differentiated collection centers according to the waste
• Electronic and electrotechnical, or returned to the dealer at the rate of the purchase of new equipment of equivalent lipo, on a one-to-one basis, or 1 to zero for equipment with a longer side of less than 25cm. Adequate separate collection P3f the rMO disposed of for recycling Look, environmentally compatible treatment and disposal helps to avoid possible negative effects on the environment and on health by promoting the recycling of materials 9 of which make up the equipment. The abusive disposal of the product by the user entails administrative sanctions referred to in the Decree Legislative Decree No. 49 of 14 March 2014.

tecnoswitch.com
Via P. Leone Dehon , 99/105 76123 Andria (BT) ITALY arealed.it tel (+39) 0883 555323 fax (+39) 0883 555323

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>