WIRELESS PACIFIC X100R Out of Vehicle Communication Solution User Guide

WIRELESS PACIFIC X100R Out of Vehicle Communication Solution

How to install Programmer

Runs On PC or Mac running Windows 7/10
NOTE: Requires USB 2 Port. The programmer will not work with USB 3 – if your PC only has USB3 ports suggest you attach X10DR device via a usb patch block most are USB 2.)
Included with the Programmer download file application are instructions on how to set-up the programmer on your Windows 7/10 PC. Please follow those instructions to install the programmer correctly onto your computer.

How to use Programmer

Runs On PC running Windows 7/10
Requires USB 2 Port.

To put Handset into programming mode:
Turn off handset, attach programming cable between device hirose port and PC then press red handset on/off button while holding PTT. The
handset’s LED will light red.

To put Gateway into programming mode:
Turn off gateway. Then hold gateway ON/OFF button down while attaching the programming cable to device micro-USB port and PC USB port. The Gateway’s LED will light red. Note: The gateway’s RJ45 socket should not be connected to the host radio.

Always READ device before proceeding further.
We suggest you SAVE the file onto your PC for re-loading if required. A GREYED out feature means your device does support that capability.

Read Device
Press to load current programming parameters from device to screen.

Program Device
Press to load current screen programming parameters to a device.

Restart (important)
Press to restart programmed device before removing programming cable.

Lock – Unlock File
Press to lock your desired parameter configuration before undertaking batch fleet programming. This will prevent you errantly changing a parameter unknowingly during reprogramming.

Load File
Press to load a previously saved programming parameters to device from its saved PC location.

Save File
Press to save a programming parameters from screen to desired PC location saved location.

Defaults
Press to reset with default device parameters

Exit
Press to exit program.

Radio PTT key beep
Sounds talk permit two tone sequence whenever PTT is pressed and handset is within range of its gateway.

Default – OFF
Emergency key beep
Sounds single tone whenever Emergency button is pressed and handset is within range of its gateway.

Default – ON
Talkaround PTT key beep
Sounds talkaround triple tone sequence whenever Talkaround button is pressed and handset is within range of its gateway.

Default – ON

Handset Parameters

Stealth mode always active
Disables all alert tones and LED status light. User can manually enable stealth mode if programmed off.

Default – OFF
Mute speaker on PTT
Disables all speaker audio whenever PTT is pressed.

Default – OFF
Mute speaker on charge
Disables speaker when handset is in gateway or a charger.

Default – ON
LED charge indicate
Disables “momentary blink” charge indicate when handset is placed into gateway or a charger and device is charging.

Default – ON
Auto turn on when charging
Causes handset to automatically turn on whenever it is placed in gateway or a charger.

Default – ON
Minimum volume is off
Allows user to turn the speaker audio off instead of level 1.

Default – OFF
Mandown Biometeric Monitor (when fitted)
Enables/disables function via programmer for Plus handsets fitted with XMD option.

Default – OFF
Internal Mic Only Operation
Maintains operation via internal microphone when accessory attached to Hirose port.required for earpiece (WPEH-X10/WPTEP-X10) use via Hirose headset port.

Default – OFF
Out of range turn off time
Sets time in hours that a handset that is not actively connected to a gateway will remain powered on before turning itself off.

Default – 8 hours
Low battery beep voltage
Sets the remaining battery voltage that will cause the low battery alert tones to be generated. (for longer shift life you may set voltage lower but you may get less warning before device automatically shuts off.

Default – 3.5V
Low battery beep interval timer
Sets the interval that the low battery alert tones are sounded in the handset. Default – 5 minutes

Elite Plus Only Options
Handsfree Function (shows “disabled” if feature not enabled)
Enables user selectable handsfree intercom function in Elite Plus handsets. Default – ON

Toggle PTT/TA Button Assignment
Configures handset so that pressing the top grey Control button toggles the side PTT button assignment between host radio PTT and Talkaround or 2nd Radio device PTT /PA Mode when used with XSJB or similar.

Default – OFF
Command Relay Mode / Automatic Relay Mode
Selects the Relay Mode type in Elite Plus handsets.
Default – Command Relay (manual – normally OFF)

Handset Programming

Basic functions

We recommend you use the XGALA Gateway Audio Level Adjustment software tool for setting levels between host radio and X10DR gateway. It can be downloaded at www.x10dr.com for setting audio in and out between the gateway and the host mobile radio.
The following handset adjustments are designed to cater for different audio accessories and/or user applications requiring alternate audio sensitivities to suit different operating conditions.

Internal Mic Gain
Sets the internal microphone’s transmit audio level sensitivity. Default – 3

Internal Mic High Gain Boost
Sets the internal microphone’s sensitivity when “Live Mic” is active. Default – 6

External Mic Gain
Sets the external microphone’s transmit audio level sensitivity. Default – 6

External Mic High Gain Boost
Sets the external microphone’s sensitivity when the X10DR’s “Live Mic” is active or when user manually selects high gain by powering up microphone with blue volume up button pressed.

Default – 6
Remote PTT Gain Boost
Increases sensitivity of internal microphone when remote/handlebar PTT is pressed.

Default – 9
Fixed Alert Tone Volume
Limits all user monitored alert tones to level set below rather than being controlled by handset volume controls .

Default – OFF

Audio Levels

Alert Tone Volume
Sets the value of the “Fixed Alert Tone” when enabled that a user will hear from their handset.

Default – 5
When handset is configured for press & hold emergency
Audio link active time
Sets the duration the transmit audio is active after Emergency button is released. Feature is intended for those mobiles that activate their own internal “Live Mic” function whenever emergency is triggered. This allows the handset’s Tx audio to be broadcast over the radio’s transmit channel, (assuming mobile sources “Live Mic” from its external mic input). Default – 0

When handset is configured for short/long press emergency
Transmit Time
Sets the time duration that X10DR “Live Mic” handset Tx audio is active when Advanced Emergency activated.

Default – 0
Receive Time
Sets the time duration that X10DR “Live Mic” handset Rx audio is active when Advanced Emergency activated.

Default – 0
Emergency repeat cycles
Sets the number of “Live Mic”, Tx and Rx cycles when Advanced Emergency is triggered.

Default – 1
Transmit audible emergency tone
Causes an audible emergency warble tone to be transmitted over the host mobile radio channel when emergency is activated.

Default – Off

Emergency

Hirose Pin 2 function
Sets Hirose pin 2 to be either BAT+ (~3.3VDC) to power external accessories or bridged output speaker audio when pin 2 is set for speaker negative.

Default – Speaker -VE
Acc PTT
Sets whether Hirose PTT input generates Talkaround or Radio PTT.

Default – Radio PTT
PTT
Sets function of main large PTT button. Choose from drop down box.

Default – Radio PTT
Top 1
Sets function of top left button. Choose from drop down box.

Default – Emergency
Top 2
Sets function of top right button. Choose from drop down box.

Default – Talkaround PTT
Left 1
Sets function of top left button.

Default – short press Volume up / long press Relay mode OFF/ON (Elite Plus only)
Left 2
Sets function of bottom left button.

Default – short press: Volume down
Right 1
Sets the function of right side button. Re-assigning requires hardware modifications. Default – short press: Search / long press: Power OFF/ON

Long Press Duration
Sets time button must be pressed to action a Long Press.

Default – 5000mSec

Hardware

Dropdown box button assignment selection

Elite Plus Handset Right 1 Button – Short Press Assignments:
Search – Resets connection to its paired gateway, other paired gateways or Relay Mode paired handsets
LTE RSM On/Off – Toggles transmit function between configured X10DR functionality to a dedicated LTE (PoC) configured smartphone attached via curly cord – LED glows white when On. (For use with X10DR-EX2-LTE models only)
Aux 1 (or 2) – Can be used to trigger Emergency when used with XFSB/ XSJB(V2) Smart boxes in dual radio deployments.
Relay Mode On/Off – Toggles Relay Mode ON or OFF to allow handsets to talk directly or mesh back to vehicle when one handset is out of vehicle gateway range.
Default – Search (Pro Plus Models can only access Search function)

Elite Plus Handset Right 1 Button – Long Press Assignments:
On/Off – Manually powers Off and On the handset.
Power On – Manually powers ON a handset that is OFF. When so assigned we suggest that the blue Volume Down button (L2) be programmed for Long Press: Power OFF for intuitive operation (other buttons can be chosen if desired). This assignment is suggested when short press is assigned other than to its default setting.
Default – Off/ On

Elite Plus Handset Top 1/2, Left 1/2 Button – Short Press Assignments:
Disabled – Button has no function
Volume Up – Increases handset speaker audio volume in 7 steps.
Volume Down – Decreases handset speaker audio volume in 7 steps.
Aux 1 (or 2) – Can be used to trigger Emergency when used with XFSB/ XSJB(V2) Smart boxes in dual radio/ wireless device deployments.
Emergency – Triggers Emergency on host mobile/wireless network device where available. HF On/Off – Toggles Handsfree local full duplex intercom operation ON / OFF.
Relay Mode On/Off – Toggles Relay Mode ON / OFF to allow handsets to talk directly or mesh back to vehicle when one handset is out of vehicle gateway range.

Elite Plus Handset Top 1/2, Left 1/2 Button – Long Press Assignments:Left 1
as per above short press selection but with following addition assignable function:

Power Off – Manually powers OFF a handset that is ON. (Suggested button assignment : Volume down (L2) button)

Gateway Parameters

*We highly recommend use of the XGALA Gateway Audio Level Adjustment tool for setting audio levels. Download here:
https://www.x10dr.com/wp-content/uploads/2020/11/XGALA-Gateway-Audio- Level-.zip

Audio Levels

Receiver Input Gain From Radio
Sets the receive input sensitivity. Default – 0

Transmit Output Gain To Radio
Sets the audio output level to radio when local/remote /handlebar PTT is pressed or when “Live Mic” is active. Default – 0

Talk Around Output Gain to other X10DRs
Sets the “intercom” microphone audio level. Default – 0

Find Me™ Function
Enables Find Me function in gateway. User double presses gateway Function button to trigger Find Me alert tones or triggers Remote FindMe.

Default – OFF
Radio Receive VOX/COR
Enables VOX derived COR.

Default – ON
VOX Trigger Level
Sets the gateway’s audio detect sensitivity for VOX derived COR. Default – 70

Public Address Mode
Sets the gateway so only handset Talkaround audio is sentto the gateway 3.5mm jack. When unchecked both Radio PTT and Talkaround audio is available for in- car monitor use.

Default – OFF
Monitor Emergency Input Alert Tone
Causes Emergency warble alert tone to sound in all cross connected X10DR handsets whenever emergency input is triggered. (i.e. triggered from another gateway or externally supplied ground input).

Default – OFF
Trunking Support
Enables speaker audio upon PTT for 500mS, so host trunked mobile’s Channel Grant /Talk Permit tones can be clearly distinguised by user. Handset Mic audio is also muted for 500mS to prevent those tones being rebroadcast over talkgroup. For optimum performance set VOX trigger level for 90-100 for fastest response.

Default – OFF

Elite Plus Series Only Options

Multi Operational Mics
Allows two or three Elite Series Mics to be simultaneously operational through the one Elite gateway unit.

Default – ON
Remote Find Me™
Enables Find Me function in gateway via grounding the white wire connected to pin 8 (Replaces Remote PTT function)

Default – OFF

I/O
Defines whether the specific gateway interface pin is assigned as an input or an output.

Active
Sets whether the interface pin needs to be held low or pulled up high to activate assigned functionality.

Function
Assigns desired functionality to Interface pin.
Choose the desired input or output from the dropdown boxes.

Pulse
Defines the length of time an input must be activated before the function is triggered or alternatively how long an output is activated when the assigned function has been triggered. A value of zero means an input triggers instantly .

Handset – Gateway

All rights reserved Wireless Corporation Limited ©2022
Wireless Pacific™, X10DR®, Liberate your mobile™, Find Me™, Powerfully Simple™ and their logos are trademarks or registered trademarks of Wireless Corporation Limited : Manual revision 1.4

www.x10dr.com

References

• Wireless Pacific X10DR Digital Vehicular Repeater

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>