nVent LENTON RBW34314 Reinforcing Steel Cleaning Brush Owner’s Manual

June 16, 2024
nVent LENTON

nVent LENTON RBW34314 Reinforcing Steel Cleaning Brush

nVent-LENTON-RBW34314-Reinforcing-Steel-Cleaning-Brush-
product

Product Information

Specifications

  • Product Name: Reinforcing Steel Cleaning Brush
  • Catalog Number: RBW34314
  • Material: Steel
  • Rebar Size (US): #14
  • Rebar Size (Canada): 45M
  • Diameter: 5mm
  • Length: 7.13 inches

Product Features

  • Designed for use with a 3/4, heavy duty, low-speed drill (200-350 rpm)
  • Cleans reinforcing steel bar, including the bar end

Product Usage Instructions

Preparing the Reinforcing Steel

The reinforcing steel cleaning brush is used to prepare reinforcing steel for use with nVent LENTON Cadweld. Follow these steps:

  1. Attach the reinforcing steel cleaning brush to a 3/4, heavy duty, low-speed drill.
  2. Ensure the drill is set to a speed of 200-350 rpm.
  3. Hold the brush against the surface of the reinforcing steel bar.
  4. Apply moderate pressure and move the brush along the length of the bar.
  5. Continue brushing for at least five seconds to remove rust, mill scale, dirt, and paint.

Maintenance and Safety

To ensure safe and effective usage, please follow these guidelines:

  • Keep the brush free of grease, oil, and other contaminants that could cause porosity in the filler material.
  • Do not reverse the cleaning brush while it is engaged with the reinforcing steel bar.
  • Always wear eye protection when using power-driven cleaning brushes.

FAQ

  • Q: Can I use the reinforcing steel cleaning brush with any drill?
    • A: No, the brush is specifically designed for use with a 3/4, heavy duty, low-speed drill operating at 200-350 rpm.
  • Q: How long should I brush the reinforcing steel bar?
    • A: Brush the bar for at least five seconds to ensure the removal of rust, mill scale, dirt, and paint.
  • Q: Are there any safety precautions I should take while using the cleaning brush?
    • A: Yes, always wear eye protection when using power-driven cleaning brushes to protect your eyes from debris.
  • Q: How should I maintain the cleaning brush?
    • A: Keep the brush free of grease, oil, and other contaminants to prevent porosity in the filler material.

The reinforcing steel cleaning brush is used to prepare reinforcing steel for use with nVent LENTON Cadweld. The brush is designed to remove rust, mill scale, dirt and paint in as little as five seconds.

FEATURES AND PRODUCT ATTRIBUTES

FEATURES

  • Designed for use with a 3/4″, heavy duty, low-speed drill (200-350 rpm)
  • Cleans reinforcing steel bar, including the bar end

PRODUCT ATTRIBUTES

  • Material: Steel
  • Rebar Size, US: #14
  • Rebar Size, Canada: 45M
  • Diameter: 5″
  • Length: 7.13″

ADDITIONAL PRODUCT DETAILS

  • Prior to installation, please read and understand all of the detailed instructions and safety notices provided in the nVent LENTON Cadweld Rebar Splicing System instruction manual.
  • Brushes must be kept free of grease, oil and other contaminants that could evolve gas and cause porosity in the filler material.
  • Do not reverse the cleaning brush while it is engaged with the reinforcing steel bar.
  • Eye protection should be used when using power-driven cleaning brushes.

DIAGRAMS

nVent-LENTON-RBW34314-Reinforcing-Steel-Cleaning-Brush-
fig-1

WARNING

nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury and death and/or void your warranty.

Contact

North America

  • +1.800.753.9221
  • Option 1 – Customer Care
  • Option 2 – Technical Support

Europe

  • Netherlands: +31 800-0200135
  • France: +33 800 901 793

Europe

  • Germany: 800 1890272
  • Other Countries: +31 13 5835404

APAC

  • Shanghai: + 86 21 2412 1618/19
  • Sydney: +61 2 9751 8500

Our powerful portfolio of brands

  • CADDY
  • ERICO
  • HOFFMAN
  • RAYCHEM
  • SCHROFF

nVent.com

© 2024 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners.
nVent reserves the right to change specifications without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

nVent LENTON User Manuals

Related Manuals