BRAYER Thermopot BR1097 Electric Air Pots Instruction Manual

BRAYER Thermopot BR1097 Electric Air Pots Instruction Manual

THERMOPOT BR1097

Thermopot is intended for boiling water and maintaining its temperature at a set level.

DESCRIPTION

1. Water level scale

2. Water Button

3. Spout for pouring water

4. Control panel

5. Detachable lid

6. Lid opening button

7. Manual water supply pump

8. 8. Manual pump block « »

9. Hand pump

10. Hand pump mechanical lock

11. Carrying handle

12. Body

13. Power cord connector

14. Power cord
    Control panel

15. «Keep warm» light indicator

16. Display

17. Water supply blocking light indicator

18. Water supply unlocking button «Lock»

19. Water supply on button «Water supply»

20. Reoiling button «Reboul»

21. Boiling light indicator «Boil»

22. Hot water temperature maintenance setting button «Selection C°»
    Display

23. Water temperature in the the root digital symbols

24. Water dispense symbol

25. Boiling time/keep warm time digital symbols

26. Set temperature maintenance digital symbols

27. Locking symbol

ATTENTION!

For additional protection it is reasonable to install a residual current device (RCD) with nominal operation current not exceeding 30 mA into the mains. To install RCD, contact a specialist.

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation instructions carefully before using the the root and keep it for future reference.

• Use the the root for its intended purpose only, as it is stated in this manual.

• Mishandling the thermopot can lead to its breakage and cause harm to the user or damage to his/her property and it is not covered by warranty.

• The thermopot is intended for heating and boiling drinking water only, do not heat or boil any other liquids.

• Make sure that operating voltage of the the root indicated on the label corresponds to your home mains voltage.

• The power plug is equipped with a grounding contact, plug it into the socket with

• reliable grounding contact. In case of short circuit the grounding reduces the risk of electric shock.

• Contact an electrical technician, if you are not sure that your sockets are installed properly and grounded.

• To prevent fire do not use adapters designed for connecting the plug to the mains socket without grounding contact.

• In case of sparking in the mains socket and occurrence of smell of burning, unplug the unit and apply to the organization maintaining your home mains.

• If smoke appears from the body of the thermopot, unplug the unit and take measures to prevent fire spreading.

• Do not use the thermopot outdoors.

• It is not recommended to use the unit during lightning storms.

• Protect the unit from impacts, falling, vibrations and other mechanical stress.

• Do not switch the thermopot on if the water tank is empty.

• Do not fill the thermopot with water directly from the faucet; to fill the thermopot use a suitable bowl.

• Do not place the thermopot next to the walls or close to the kitchen furniture.

• Place the thermopot keeping at least 20 cm gap between the thermopot body and the wall and at least 50 cm gap above the thermopot.

• Never leave the plugged-in thermopot unattended.

• Do not use the thermopot in proximity to kitchen sink, in bathrooms, near swimming pools or other containers filled with water.

• Do not use the thermopot near heating appliances, heat sources or open flame.

• Do not use the thermopot in places where aerosols are used or sprayed, and in proximity to inflammable liquids.

• Place the thermopot on a flat stable surface; do not place it on the edge of a table. Do not let the power cord hang from the edge of the table and make sure it does not touch hot surfaces or sharp edges of furniture.

• Do not touch the power cord and the power plug with wet hands. Do not switch the thermopot on without water, after the thermopot is filled, close the lid tightly.

• Ensure that the water level is not above the maximal mark. If the water level exceeds the maximal mark, boiling water can splash out of the thermopot during boiling.

• To avoid burns by hot steam, do not bend over the steam release openings in the thermopot lid. Do not block the steam release openings with any objects.

• Do not open the thermopot lid while water boiling.

• Be careful while carrying the thermopot filled with boiling water.

• Be very careful when pouring hot water out of the thermopot.

• Unplug the thermopot before cleaning or when you are not using it. When unplugging the thermopot hold only the power cord plug and carefully remove it from the mains socket, do not pull the power cord — this can lead to damage of the power cord or the socket or cause short circuit.

• To avoid electric shock do not immerse the thermopot into water or any other liquids.

• Do not wash the thermopot in a dishwashing machine.

• For children safety reasons do not leave polyethylene bags, used as a packaging, unattended.
  ATTENTION! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

• The thermopot is not intended for usage by children.

• Do not leave children unattended to prevent using the unit as a toy.

• Do not allow children to touch the unit and the power cord during the thermopot operation.

• Place the unit out of reach of children during the operation and cooling down.

• This unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.

• Check the integrity of the power cord, the power plug and the thermopot body periodically.

• If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.

• If the power cord is damaged, it should be replaced with a power cord received from the manufacture or service.

• Transport the thermopot in the original package.

• Keep the unit out of reach of children and disabled persons.

THERMOPOT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE COFFEE MAKER FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE USING THE THERMOPOT

After unit transportation or storage at low temperature keep it for at least 3 hours at room temperature before switching on.

• Unpack the thermopot and remove all the packaging materials.
• Keep the original package.
• Read the safety measures and operating recommendations.
• Check the delivery set.
• Examine the thermopot for damages, in case of damage do not plug it into the mains.
• Make sure that the specifications of power supply voltage specified on the label correspond to the specifications of your mains. When using the thermopot in the mains with 60 Hz frequency, the unit does not need any additional measures.
• Wipe the outer surface of the unit body (11) with a clean, slightly damp cloth to remove dust.
• Open the lid (5) by pressing the button (6) and holding it.
• Wipe the inner surface of the thermopot flask with a clean, slightly damp cloth to remove dust. Close the lid (5).

SWITCHING THE THERMOPOT FOR THE FIRST TIME AND USING THE UNIT

• Place the thermopot on a dry flat surface keeping at least 20 cm gap between the thermopot body and the wall or furniture and at least 50 cm gap above the thermopot.

• Open the lid ( 5) by pressing the button ( 6 ) and holding it.

• Fill the thermopot with water using a suitable bowl, do not exceed the maximal water level mark. Do not fill the thermopot with water directly from the faucet; to fill the thermopot use a suitable bowl ( pic. 1).
  
  Notes: to reduce the mineral deposit (scale), we recommend using the water cleaned with domestic filters.

• Close the lid (5) until the lock clicking, make sure that the lid (5) is closed.
  Notes: when using the thermopot, always check the sealing gasket. If you find any cracks on the sealing gasket, stop using the thermopot and apply to the service center to replace the gasket.

• Insert the power cord (14) jack into the connector (12) on the thermopot body, and the power cord ( 14) plug into the mains socket (pic. 2).
  

• «Boil», water supply blocking indicator ( 17) , the digital symbols ( 23 ) on the display (16 ) will show the temperature of the water in the thermopot.

• After boiling water for a long time, the thermopot will switch to the keep warm mode, the keep warm indicator (15) will light up, the digital symbols (26) on the display (16) will show maintenance temperature «85». The water temperature 85°С is set by default.
  Notes: the thermopxnd boiling of water, the time depends on the place where the thermopot is used, relative to the height above sea level.

• To avoid burns by hot steam, do not bend over the steam release openings (9) in the thermopot lid (5).
  Do not block the steam release openings (9) with any objects.

• Drain the water after the first boiling. Hot water resulting from the first boiling is not recommended to consume, you may use it for domestic needs.
  ATTENTION! Be careful when pouring out water to avoid burns by hot water.

• Unblock the water pump by pressing and holding the «Lock» button (18) for 5 seconds, the indicator (17) will go out and the symbol (27) will go out on the display (16).

• To drain the water you can do the following:
  First option: place a suitable bowl, for instance, a cup under the spout for pouring water (3) and press the water (2) dispense button with a rim of the cup (pic. 3).
  
  Second option: place a suitable dish under the water spout (3), press and hold the water supply button (19) «Water supply», after filling the cup, release the button (19) **(pic. 4).

Option 3: set the manual pump lock (8) to the position « » and press on the manual pump (7). After using the manual pump (7) lock it by setting the lock (8) to the position « ».
Notes:**

  * water is supplied only when the indicator (17) is off, if you have pressed the «Lock» button (18) and have not performed any actions, the indicator (17) will light up after 10 seconds;
  * if you haven’t used the thermopot for a long time, the water dispense may malfunction. In this case it is recommended to open and close the lid (5) and to switch the water dispense on again.

• To switch the thermopot off disconnect the power cord (14) plug from the mains socket.

• Open the thermopot lid (5) and wait until it cools down completely.

• Always drain the remaining water from the thermopot flask, to do this remove the lid (5).
  

• Before removing the lid (5) slightly open it at the angle of approximately 45°, and pull the lid (5) towards the control panel (4).

• Carefully tilt the thermopot to drain the remaining water.

• Install the lid (5) to its place; to do this, set the lid (5) at the angle of approximately 45° and insert the lid (5) to its installation place; before using the thermopot make sure that the lid (5) is fixed properly
  

Additional information

• The thermopot is equipped with rotating base (13).
  You can turn the thermopot body (11) in the required direction.

• Check the water level in the thermopot using thescale (1).

• Timely refill the thermopot.

HOT WATER MAINTENANCE TEMPERATURE SELECTION

• You can choose from six preset hot water temperature maintenance settings.
• To select the keep warm temperature, press the «Select С°» button (22), you can select the temperature for maintaining hot water «98-85-75-65- 55-45» degrees, the set temperature is displayed on the display (16) with digital symbols (26).
• Recommended water temperature for brewing tea and making other beverages:
  • «45» – water temperature for making powdered baby milk
  • «55» – brewing white tea
  • «65» – red or herbal tea
  • «85» – green or yellow tea, brewing coffee
  • «95» – black tea
• If the water temperature drops significantly below the set temperature, for example, if you added cold water, in this case the boiling mode will switch on and the indicator (21) «Boil» will light up.
• «Reboul», the indicator (21) «Boil» will light up, after boiling the water, the keep warm mode will switch on, the keep warm indicator (15) «85» will light up. The water temperature 85°С is set by default.
• To switch the thermopot off disconnect the power cord (14) plug from the mains socket.
  Note: before using the functions «selection of keep warm temperature» and «reboiling», press and hold the «Lock» button (18) for 5 seconds, the indicator (17) will go out.

CLEANING AND MAINTENANCE

• Before cleaning the thermopot unplug it (14), open the lid (5) and wait until the thermopot cools down completely.
• Always drain the remaining water from the thermopot flask, to do this remove the lid (5).
• Before removing the lid (5) slightly open it at the angle of approximately 45°, and pull the lid (5) towards the control panel (4).
• Carefully tilt the thermopot to drain the remaining water.
• Install the lid (5) to its place; to do this, set the lid (5) at the angle of approximately 45° and insert the lid (5) to its installation place; before using the thermopot make sure that the lid (5) is fixed properly.
• Clean the outer surface of the thermopot body (11) with a slightly damp cloth and then wipe it dry
• Use neutral detergents to remove dirt, do not use metal brushes, abrasives and solvents.
• Do not immerse the thermopot and the power cord (14) into water or other liquids.
• Do not put the thermopot in a dishwashing machine.

Stains on the inner surface of the thermopot flask

• Water contains various minerals that can cause stains on the inner surface of the thermopot flask, the stains do not affect the operation of the thermopot, stains are not covered by the warranty.
• You can remove the stains from the inner surface of the thermopot flask with citric acid solution or table vinegar.
• To remove the flavour of citric acid or vinegar, boil water and pour it out.
• Repeat this procedure until the smell and foreign taste vanish completely.

Removing the mineral deposits (descaling)

• Scale, appearing inside the thermopot flask, influences the water taste and disturbs the heat exchange between water and the heating element. It also risks damaging the heating element. Burning of the heating element caused by the large amount of scale in the thermopot flask is not covered by warranty.
• To remove the scale fill the thermopot with a mixture of one part ordinary vinegar and two parts water up to the maximal level mark (15).
• Insert the power cord (14) jack into the connector (12) on the thermopot body, and the power cord (14) plug into the mains socket.
• The thermopot will be switched on in the boiling mode. After the water boiling disconnect the power cord (14) plug from the socket and leave the thermopot filled with the vinegar solution overnight.
• In the morning pour out the vinegar solution, fill the thermopot with water up to the maximal level, boil it and pour out the water.
• You can use special descaling agents for electric kettles, strictly following the instruction.
• Clean the thermopot from scale regularly.

STORAGE

• Before taking the thermopot away for long storage, disconnect it from the mains, let the unit cool down and pour out the water.
• Clean the thermopot.
• Keep the thermopot out of reach of children and disabled persons.

DELIVERY SET

1. Thermopot – 1 pc.
2. Power cord – 1 pc.
3. Manual – 1 pc.

ECHNICAL SPECIFICATIONS

• Power supply 220-240 V, ~ 50-60 Hz
• Rated input power: 750 W
• In the keep warm mode: 70 W
• Max capacity: 5,5 l

RECYCLING

To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling.

The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner.

For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product.

The manufacturer reserves the right to change the design, structure and specifications not affecting general operation principles of the unit, without prior notice.

The unit operating life is 3 years
The manufacturing date is specified in the serial number.

In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>