Moonshan M90 Automatic Liquid Filling Machine User Manual

Moonshan M90 Automatic Liquid Filling Machine

INTRODUCTION

1. Power supply: The power outlet of the machine must be connected to the ground w ire.
2. Display characteristics : W eight (4 digits), Set (4 digits), Counter (4 digits), Trigger (4 digits).
3. Features: rea l-time weighing, overload alarm, automatic counting, automatic start, automatic speed conversion, automatic stop, setting data storage, delay adjustment, error correction, factory settings and other functions.

TECHNICAL PARAMETERS

| M90| 1 2 00| 3 2 00| 3500
---|---|---|---|---
Recommended filling| 0.5-109| 2-100g| 5-1,000g| 10 – 1,000g
Maximum weighing| 500g| 600g| 3000g| 3000g
Pump| Peristaltic pump| Peristaltic pump| Diaphragm pump| Peristaltic pump
Pump flow max.| 90 ml/min| 1200 ml/min| 3200ml/min| 3500ml/min
Display unit| g| g| g| g
Rated power| 10W| 20W| 30W| 40W

PANEL INTRODUCTION

Weight: displays the actual weight of the item being weighed
Set: User-set weight to be filled
Counter: number of bottles that have been filled
Trigger: the weight value that triggers the auto start

[Man] : manual mode
[Auto] : automatic mode
[Tare]: Peel and set to zero
[Set]: set the filling weight
[Trig]: set the trigger value
[Run]: manually start the filling function (click again to pause)
[Save]: store 4 groups of commonly used filling data
[M1 -4] : Call the stored filling weight data
[ 0 ]: Counter value is cleared
The big green button and foot switch have the same function as the [Run] on the keyboard.

OPERATION

1. “Set” setting method:
   Press the [Set] key, enter the value (e. g. , set 1OOg, enter 1 0 0), and then press [Set] again to save the data and exit.

2. “Trigger” setting method : (trigger value can not be less than 3 grams)
   Press the [Trig] key, enter the value (e.g. , set 35g, enter 3 5), and then press [Trig] again to save the data and exit.
   Note: The trigger value is set to ≤ empty bottle weight. In automatic mode, the automatic filling is triggered when the weight of the empty bottle exceeds the trigger value.

3. “ Manual mode” operation method: (Press the [Man] key, the manual light is on, enter the manual mode;)

4. Place the empty bottle, press the [Tare] button to clear the empty bottle weight, press the [Run] button to start the filling. When the weight of the poured liquid reaches the set filling weight, the filling machine will stop automatically.

5. Remove the filled bottle, place another empty bottle, press the [Tare] [Run] button to start the next filling.

6. “Automatic mode” operation method: (Press the [Auto] key, the automatic light is on, enter the automatic mode)

7. Place the empty bottle, the system automatically tare and automatically starts filling. When the weight reaches the filling weight, the filling is automatically stopped.

8. Remove the filled bottle and the system will automatically reset to zero. Place another empty bottle and the fil ling machine will automatically start filling.
   Note: When using the automatic mode, if the machine is not properly filled, it is because of a mistake caused by a cycle not end yet. At this point, remove the bottle and press (Tare] to make it Work normally.

9. The setting method of “storing 4 groups of fil ling weights to M1-M4”:
   Press the [Save] key (the number of filling weights starts to flash), input the value to be stored, and press the [M 1] key (the number of “filling weight” stops flashing) and the number to be entered will be stored in M1. When you need to use the value of M1 as the filling weight, press M1 to call out the data. (Set M2, M3, M4 as the method of setting M1)

10. How to cancel the automatic tare function:
    Restart the machine, press the [Auto] button, and then press and hold the [3] button until you hear the beep sound of the machine and release the button. At this time, the automatic tare function has been canceled. If you want to turn on the automatic tare function, repeat the above operation. Once set up, the machine will remember the setting.

11. How to set the “MID-RANGE DECELERATION RATIO “: Set the percentage at which to start decelerating when reaching the preset value Press [Auto] , set the flow rate to a proportional value (e. g. , 80) , press and hold the speed knob until there is a “Beep” sound.

12. How to set the “The value of slow down” : (How many grams before the end automatically slows down) Press [Trig] [Save]at the same time, then enter the value to be set , and then press [Trig] again.

13.   “factory settings” method: press the [ auto ] button, and then press and hold the [5] button until there is a 11beep11 sound. The machine is back to factory status.

OPERATION

1. This liquid fil ling machine has flow rate adjustment knob, speed 1-100 adjustable, and digital display flow rate value;
2. Rotating knob adjustment, t he speed value w ill be digital display, no operation 3 seconds after the exit.
3. Press the speed knob, the flow rate value will be displayed on the line of [Trigger]], no operation after 3 seconds exit.
   Flow rate can be adjusted at any time, and the adjustment will automatically be saved.

HOW TO USE JHE SET TIME METHOD OF FILLING

1. Press [ Auto], press and hold [2] to switch to “the set time method of filling” (the same method can also be restored to “the set weight method of filling”).
2. The set time method of filling displays the number in seconds, accurate to 0.01 seconds.
3. Press [ Settings], enter filling time, press [Settings] to set the filling time.
4. Press [Trigger], enter interval time, press [Trigger ] to set the interval time of automatic filling.
5. Press [ Set][ Start ] at the same time, enter the amount needed, then press[ Set] [ Start] to extract filling time.
6. Under automatic mode, the filling machine can be started by setting a value of interval, while under manual mode, you should press the start button to start.

NOTIFICATIONS

1. The user shall select a quantitative filling machine of suitable range according to the chart in the part II. Parameter.

2. Please check its accu racy before use.

3. The machine contains precision electronic scale, it is forbidden to be overweight.

4. The Height of filling head can be adjusted to about 10 mm from the bottle mouth.

5. When in use, please keep the machine level and stable to avoid big vibration or impact, otherwise it may cause damage.

6. Before first use or long time no use, very few w ill not absorb water, because the pump inside is dry. Please manually add liquid into the inlet tube to active the pump and then start the machine.

7. It is better to clean the machine with clean water after every use, which can prolong the service life of the pump.
   

8. When the machine is not in use, please empty the liquid and store it in a ventilated and dry place.
   

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>