Taylor T-6768R Reversible Drill Installation Guide
- June 16, 2024
- TAYLOR
Table of Contents
Taylor T-6768R Reversible Drill
Product Information
Specifications
- Model: T-6768R, RK / T-6768HR, HRK
- Type: Reversible Drill
- Chuck Size: 3/8″ (T-6768R, RK) / 1/2″ (T-6768HR, HRK)
- Oiling Instructions: Oil after each use with a few drops of airtool oil through the air inlet. Run for 1 second to coat all internal parts.
- Maximum Air Pressure: 90 PSI
Parts List
| Ref # | Part # | Description | Qty |
|---|---|---|---|
| 1 | 6768R01 | MOTOR HOUSING | 1 |
| 40 | 6768R40 | GEAR | 3 |
Accessories
- 31. T-7788-KC: 3/8″ Keyless Chuck
- 31A. T-7788HR-KCN: 1/2″ Keyless Chuck
- 31B. T-7788-C: 3/8″ Chuck & Key
- 31C. T-7788HR-C: 1/2″ Chuck & Key
Warranty Information
For warranty information and warranty registration, please visit www.taylorpneumatic.com.
Contact Information
- Address: 505 N. Railroad Ave. 33435 P.O. Box 1117 33425 Boynton Beach, FL
- Phone: (561)732-1111
- Fax: (561)731-4412
- Toll Free: 800-805-8665
Product Usage Instructions
Oiling Instructions
- After each use, apply a few drops of airtool oil through the air inlet.
- Run the drill for 1 second to ensure all internal parts are coated with oil.
Air Pressure Limit
Do not exceed a maximum air pressure of 90 PSI when using the drill.
Chuck Replacement
To replace the chuck, follow these steps:
- Remove the chuck screw (32) using the appropriate tool.
- Detach the old chuck from the spindle.
- Attach the new chuck securely onto the spindle.
- Tighten the chuck screw (32) to secure the new chuck in place.
Cleaning and Maintenance
To ensure optimal performance and longevity of the drill, follow these
cleaning and maintenance guidelines:
- Regularly clean the exterior of the drill with a damp cloth to remove dirt and debris.
- Inspect the drill for any signs of damage or wear.
- If necessary, disassemble the drill and clean each part individually using a mild detergent and water.
- Dry all parts thoroughly before reassembly.
- Apply a few drops of airtool oil to the internal parts before reassembling.
Safety Precautions
When using the drill, please observe the following safety precautions:
- Wear appropriate protective gear such as safety goggles and gloves.
- Ensure the work area is well-lit and free from any hazards.
- Keep fingers and loose clothing away from moving parts.
- Do not operate the drill if you are fatigued or under the influence of drugs or alcohol.
- Always disconnect the drill from the air supply before performing any maintenance or cleaning.
Frequently Asked Questions (FAQ)
-
How often should I oil the drill?
It is recommended to oil the drill after each use to ensure proper lubrication of internal parts. -
Can I use this drill with a higher air pressure than 90 PSI?
No, exceeding the maximum recommended air pressure can lead to damage to the drill and potential safety hazards. Please always operate within the specified limit. -
How do I register my warranty?
Warranty registration can be done online at www.taylorpneumatic.com. Please follow the instructions provided on the website. -
Can I use any chuck size with this drill?
The drill is designed to accommodate both 3/8″ and 1/2″ chuck sizes. Please refer to the accessories section for compatible chucks.
OILING INSTRUCTIONS
OIL AFTER EACH USE WITH A FEW DROPS OF AIRTOOL OIL THROUGH THE AIR INLET. RUN
FOR 1 SECOND TO COAT ALL INTERNAL PARTS.
EXPLODED VIEW
PART LIST
ABOUT COMPANY
- 505 N. Railroad Ave. 33435
- P.O. Box 1117 33425
- Boynton Beach, FL
- FOR WARRANTY INFORMATION & WARRANTY REGISTRATION VISIT www.taylorpneumatic.com
- Ph. (561)732-1111
- Fax. (561)731-4412
- Toll Free 800-805-8665
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>