LISEN 2E769 Magsafe Car Mount Charger User Manual

2E769

2E769 Magsafe Car Mount Charger

Thanks for choosing Lis.en! To bring you a fantastic experience please read the manual before using

PRODUCT ACCESSORY LIST

PRODUCT STRUCTURE

PRODUCT PARAMETERS

PRODUCT MODEL
2E769
MATERIAL
ZINC ALLOY
INPUT
5V 2A 9V 2A
OUTPUT
5w×754×104×15w
DIMENSIONS
24×58×58mm
WEIGHT
˜1209

COMPATIBLE DEVICES

1. Headphones: Airpods pro (with ma­ gsafe battery compartment) / Airpods pro 2nd generation.
2. iPhone 12/13/14 series naked/with magsafe case/third party case without magsafe case requires additional ma­ gnetizer.
3. With wireless charger does not sup­ port magsafe phones, you need to use a magnetizer.
4. Without wireless charger phone, need to use magnetizer (only car mount function, no wireless charger function)

INSTALLATION STEPS FOR THE BRACKET

1. Before installing the bracket, please ensure the desired placement for adh­ esive use, to avoid the need for disma­ ntling and reapplying the bracket due to unsuitable position or angle (reapp­ lying with adhesive may result in inst­ ability or detachment risks).
   

2. Open the wet wipes and clean the intended adhesive area to ensure there is no dust or foreign particles that may affect the adhesive’s effectiveness.
   

3. After wiping with the wet wipes, use a dry cloth to wipe the cleaned area to ensure it is dry.
   

4. Peel off the protective film on the adhesive surface at the bottom of the bracket. Place the bracket firmly on the leaned area and press it down firmly Allow it to rest undisturbed for 24 hours before normal usage. (During the bracket installation process, do not touch the adhesive with hands or other objects after removing the adhesive fimn, as it may affect the adhesive’s effectiveness).
   

5. In order to achieve a stronger adhesion of the product, please refer to the dia­ gram for instructions. After applying the auxiliary sticker, it needs to be left und­ isturbed for 12 hours before removing it.
   

GUIDE DISK INSTAL­LATION PROCEDURE

1. Tutorial on the use of the magnetic lead sheet.
   Tips: uneven surface of mobile phone cases, liquid silicone cases, oil spray­ edcases, fabric and leather cases are not suitable for this magnetizer.
   

2. If your case does not have the mag safe function, please follow the steps below to use the magnetic pad to ach­ ieve the magnetic suction function.
   

3. lace the magnet locator on the ba­ ck of the phone/case, aligning the edges of the phone and making sure the top and bottom/left and right scales are the same; remove the protective fim from the magnet and stick it to the centre of the magnet locator.
   

NOTES

1. About using non-standard car charger: please use QC3.0 or pp18W or above.

2. Metal accessories (iron pieces, finger rings) or credit cards can interfere with charging. Cases containing metal, such as Pitaka, Evutec and Spigen QNMp, will trigger foreign object detection and interrupt charging.

3. Using the phone for GPS navigation or listening to music while charging can significantly affect the charging speed.
   When using Gps applications, the power consumption may be higher than the charging speed.

4. It is normal for the wireless charger to heat up slightly during use. If you exper­ ience severe heating, please suspend use and contact our after-sales email.

PRODUCT WARNINGS

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in ac­ cordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that  interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television re­ ception, which can be determined by turning the equipment off and on, the user is encouraged to try to cor­ rect the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
• Thie equipment must be installed and operated with a minimum distance of 5 cm between the radiator and user body.

365 DAY
Worry-free 365-Day Warranty

24 HOURS
24/7 Easy-to-Reach Support Email
support@lisen.com, get connection within 24 hours.

AMZLAB GmbH Laubenhof 23, 45326 Essen

UKCA SERVICE LTD 21 Ellesmere
Avenue,Worsley,Manchester,UK,M28 OAL

AFTER SALE SERVICE

Lisen always dedicates to bring greats.hopping
experience for each customer, Please feel free to contact us if you have any question.

@LISEN Tech
support@LISEN.com
@LISEN Tech
@LISEN Tech

Shenzhen Xiangdangwen Technology Co., Ltd.

ADDRESS: 106, 1/F, No.313-4 Building
Huachang Road,Langkou
Community Dalang Street
Longhua District,
Shenzhen, China.

MANUFACTURE: Huizhou Yimai Ele-
ctronics Technology
Co.Ltd.

ADDRESS: 3rd Floor, Building B, Hu-
akai High-tech Industrial
Park, Electronic CityRoad,
Longxi Street,Boluo County.

Designed by LISEN Made in China

Documents / Resources

| LISEN 2E769 Magsafe Car Mount Charger [pdf] User Manual
2E769 Magsafe Car Mount Charger, 2E769, Magsafe Car Mount Charger, Car Mount Charger, Mount Charger, Charger
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>