EMPIRE Grey Vanity with Chrome Handles Instruction Manual

June 16, 2024
Empire

EMPIRE Grey Vanity with Chrome Handles

Product Information

Specifications

  • Wall hung unit height: 850mm (including basin height)
  • Drawer position: adjustable
  • Distance between brackets on wall hung unit: L
  • Distance between pre-drilled holes on mirror cabinet and storage unit: L & H
  • Distance from floor to bottom of storage: customer’s request

Tools Required for Installations

  • Suitable fixings for securing the unit to the wall
  • Screwdriver
  • Silicone for sealing
  • Button for removing/installing metal drawer
  • Plug screws with chrome covers for mirror cabinet and storage unit

Product Usage Instructions

Hinge Adjustment

To adjust the door hinges:

  1. For vertical adjustment, loosen screw A on all hinges, adjust the door, and retighten the screw.
  2. For lateral adjustment, loosen screw B, adjust the door, and retighten the screw.
  3. For horizontal adjustment, follow the instructions for drawer removal/installation (Step A) according to the drawer position on the unit.

Drawer Removal/Installation

To remove the metal drawer:

  1. Press the button as shown in Step A.
  2. Pull out the drawer in a level position.

To install the metal drawer:

  1. Press the button as shown in Step A.
  2. Push in the drawer in a level position.

If drawer position needs altering:

  • Follow Step B or C according to the drawer position on the unit.

Wall Hung Unit Installation

(Fixings are included in the box)

Please measure the distance (L) between each bracket on the unit and the desired height (H) from floor to wash basin. The standard height is 850mm (including basin height).

  1. Attach the brackets to the wall according to the measured distance (L).
  2. Position the wall hung unit onto the brackets.
  3. Secure the unit to the wall using suitable fixings through the pre-drilled holes in the back panel.
  4. Adjust the handle to the middle position.

Mirror Cabinet and Storage Unit Installation

(Plug screws with chrome covers are included in the box)

Please measure the distance (L) and (H) between each pre-drilled hole on the products. The distance between the mirror cabinet and basin should be 300-400mm. The distance from floor to bottom of storage can be adjusted according to customer’s request.

  1. Fix the plug screws with chrome covers into the pre-drilled holes on the mirror cabinet and storage unit.
  2. Position the mirror cabinet and storage unit onto the desired location.
  3. Secure the units to the wall using suitable fixings through the plug screws.

FAQs

Q: How do I adjust the door hinges?

A: To adjust the door hinges, loosen screw A for vertical adjustment, loosen screw B for lateral adjustment, and follow the instructions for drawer removal/installation for horizontal adjustment.

Q: How do I remove/install the metal drawer?

A: To remove the metal drawer, press the button as shown in Step A and pull it out in a level position. To install the metal drawer, press the button as shown in Step A and push it in in a level position.

Q: How do I install the wall hung unit?

A: Measure the distance (L) between each bracket on the unit and the desired height (H) from floor to wash basin. Attach the brackets to the wall, position the unit onto the brackets, secure it to the wall using suitable fixings, and adjust the handle to the middle position.

Q: How do I install the mirror cabinet and storage unit?

A: Measure the distance (L) and (H) between each pre-drilled hole on the products. Fix the plug screws with chrome covers into the pre-drilled holes, position the units onto the desired location, and secure them to the wall using suitable fixings.

BATHROOM FURNITURE FITTING GUIDE

Tools required for installations

Note: For safety reasons Unit must be secured to the wall using suitable fixings (pre-drilled holes provide in back panel of unit)
When fitting a basin to a unit, a bead of silicone should be applied to the top edge of the basin unit to seal between the basin and unit.

Please spend 5 minutes reading this section before commencing with the installation of your new furniture

  1. Should any of your items have a defect, please do NOT install as returns will not be accepted once fitted.
  2. We advise that you use a qualified person to install your units, as any issues relating to poor fitting will not be accepted by the supplier.
  3. You have purchased a handmade and in some cases hand painted product. Therefore, you may see some slight imperfections which the supplier may deem as acceptable.
  4. This product is water resistant but NOT waterproof. On no account should any spillages or splashes, even water, be allowed to lie on any surface. All spillages and splashes should be wiped dry, failure to do so may shorten the life expectancy of the product and invalidate any guarantees.
  5. Please avoid direct sunlight as this will cause the painted surfaces to discolour.
  6. Due to motion in transit, the cabinet doors and drawers may need to be adjusted after installation.
  7. Floor Standing units must be fitted back to the wall through the backrail using suitable fixings. (not supplied)
  8. Basin units should be fitted as above. The basin should also be secured where applicable using Fischer bolts through the fixing points under the basin. (not supplied) Note that not all basins have this facility.
  9. Wall Hung units must be secured back to the wall using the wall hanging brackets or suitable wall fixings when not supplied. Additional support is recommended using ‘L’ brackets. (not supplied)
  10.  When fixing to a stud or panelled wall, appropriate frame work should be installed to support the basins and units…
  11. Where units or worktops have to be cut-out for services, all raw edges MUST be sealed against water ingress.

Hinge Adjustment

Drawers Remove/Install

  • To Remove the metal drawer: press the button as follow Step A, then pull out in level position ;
  • To Install the metal drawer: press the button as follow Step A, then push in in level position
  • Drawer position: if drawer position needs altering follow Step B or C according to the drawer positon on unit.

BATHROOM FURNITURE CUSTOMER CARE GUIDE

Please note that although these units have been designed to give years of pleasure and satisfaction, you will help maintain the original beauty of your bathroom by following these guide lines.

  • Melamine, Vinyl and Foil Wrapped Doors
    Occasional marks, can in most cases, be removed with a soft damp cloth. More persistent marks can be removed using a non silicone based furniture cleaner. Hot soapy water should be avoided. Once
    the mark is removed, the area should be wiped over with a damp cloth to remove any excess and dried with a soft clean cloth. On no account should solvent or an abrasive cleaner be used as permanent damage to the finish could take place.

  • High Gloss Doors
    Use a cleaning product not containing aggressive substances like acetone, alcohol, bleach … as those components could seriously damage the surface of the door. The best would be to use a soft cotton or micro fibre cloth with only water and soft soap (containing a maximum 1% of liquid soap)

  • Carcase Components
    Do not use polish on any surfaces. A damp cloth with soapy water will clean off most marks or spills. Bleaches, scouring pads and multi-surface cleaners should not be used.

  • Drawers, Runners, Door Hinges
    These should be wiped out with a damp soapy cloth and wiped dry with a soft cloth as necessary. The roller runners and hinges are lubricated and should not be cleaned with a degreasing agent as this will affect the action of the moving parts. Never lean on partially or fully opened doors and drawers in order to gain access to the units. The hinges are specified to adequately support the weight of the door, plus small additional weights such as wire accessories. It is advised that once the bathroom has been installed you should check every six months that all screws on the hinges are tight.

  • Worktops
    Although the worktop is hard wearing, sharp objects will scratch and excessive heat will scorch the surface. Care should be taken not to drop any heavy objects onto the worktop as the surface may crack.
    For cleaning, a damp soapy cloth will clean off most spills. Bleaches, scouring pads and multi-surface cleaners should not be used. Corrosive liquids and make-up should be wiped off immeadiately. On no account should any spillage, even water, be allowed to lie on the surface.

  • Temperature and Humidity
    Avoid excessive change in temperature and humidity. Always try to ensure adequate ventilation.

  • General care, spillages and splashes
    On no account should any spillages or splashes, even water, be allowed to lie on any surface.
    All spillages and splashes should be wiped dry, failure to do so may shorten the life expectancy of the product and invalidate any guarantees.

Wall hung unit installation.

( fixings in box)

  • Please measure the L distance between each brackets on unit. and H ( height as customers request. The standard height is 850mm (including basin height) from floor to wash basin
  • Mirror cabinet and Storage unit. ( plug screws with chrome covers in box)
    Please measure the L&H distance between each pre-drilled holes on products.and fixing them as below steps.the distance will be 300-400 the mirror cabinet to basin as below . the distance from floor to bottom of storage as customer requests.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals