EMPIRE VFSE-18-1 Gas Log Heater Instruction Manual

VFSE-18-1 Gas Log Heater

“`html

Specifications:

• Product Name: Empire Comfort Systems Vented/Vent-Free
  Burner

• Models: VFSE-(18,24,30)-1, VFSV-(16,18,24,30)-4

• Gas Type: Natural Gas (specified on rating plate)

• Heater Type: Unvented Gas-Fired Heater

Product Usage Instructions:

Quick Start Guide:

Refer to pages 3-4 for a quick start guide on setting up and
operating the burner.

Important Safety Information:

Follow all safety precautions mentioned in the manual to prevent
fire, explosion, or exposure to harmful substances.

Requirements for Canada:

For installation in Canada, ensure compliance with local codes
and regulations. Refer to page 7 for specific requirements.

General Information:

This appliance requires adequate combustion and ventilation air.
Refer to page 11 for detailed instructions on providing proper
ventilation.

Water Vapor Production:

An unvented gas-fired heater produces water vapor as a
by-product of combustion. Refer to page 10 for information on water
vapor production.

Clearances:

Ensure proper clearances as specified on pages 11-12 to prevent
overheating and potential hazards.

Combustible Material:

Avoid placing combustible materials near the burner. Refer to
page 13 for guidelines on keeping the area around the appliance
clear.

FAQ:

Q: Can this burner be used with propane gas?

A: No, this appliance is designed for use with natural gas only
as indicated on the rating plate. It is not convertible for use
with propane gas.

Q: How often should the burner be serviced?

A: Regular maintenance and service should be performed by a
qualified installer or service agency at least once a year to
ensure safe and efficient operation.

“`

EMPIRE
Comfort Systems

INSTALLATION INSTrucTIONS AND OwNer’S MANuAL

Vented/Vent-Free Burner

uNVeNTeD GAS LOG HeATer Or
INTerMITTeNT MODeLS VFSE-(18,24,30)-1
VArIABLe MODeLS VFSV-(16,18,24,30)-4
VeNTeD DecOrATIVe APPLIANce
VArIABLe MODeLS VFSV-(16,18,24,30)-4
GAS-FIRED

Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference.
WARNING: If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
— wHAT TO DO IF yOu SMeLL GAS · Do not try to light any appliance. · Do not touch any electrical switch; do not use any phone in your building. · Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. · If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service agency or the gas supplier.

This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.
This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to page 11.
WARNING: If not installed, operated and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or from fuel combustion which can cause death or serious illness.
wATer VAPOr: A By-PrODucT OF uNVeNTeD rOOM HeATerS Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one (1) ounce (30ml) of water for every 1,000 BTU’s (.3KW’s) of gas input per hour. Refer to page 10.
Page 1

TABLe OF cONTeNTS

Section

Page

Quick Start Guide ………………………………………………………………………………………………………… 3-4

Important Safety Information ……………………………………………………………………………………………. 5

Safety Information for Users of LP-Gas …………………………………………………………………………….. 6

Requirements for Canada ……………………………………………………………………………………………….. 7

Introduction……………………………………………………………………………………………………………………. 8

Product Specification………………………………………………………………………………………………………. 9

General Information………………………………………………………………………………………………………. 10

Water Vapor: A By-Product of Unvented Room Heaters …………………………………………………….. 10

Provisions for Adequate Combustion & Ventilation Air ……………………………………………………….. 11

Clearances ……………………………………………………………………………………………………………… 11-12

Combustible Material…………………………………………………………………………………………………….. 13

Fireplace Preparation ……………………………………………………………………………………………………. 13

Installing as a Vented Appliance……………………………………………………………………………………… 14

Before Fully Installing the Appliance ……………………………………………………………………………….. 14

Gas Supply ………………………………………………………………………………………………………………….. 15

Placement of Glowing Embers and Lava Rock …………………………………………………………………. 16

Operation Instructions/Flame Appearance ……………………………………………………………………….. 16

G6R-P3TAN5 Remote Control Instructions …………………………………………………………………..17-20

VFSE-(18,24,30) Lighting Instructions …………………………………………………………………………….. 21

VFSV-(16,18,24,30) Lighting Instructions…………………………………………………………………………. 22

Pilot Flame Characteristics…………………………………………………………………………………………….. 23

Cleaning and Servicing …………………………………………………………………………………………………. 24

Wiring …………………………………………………………………………………………………………………………. 24

Troubleshooting Symptoms – Possible Causes and Correction …………………………………………… 25

Parts List……………………………………………………………………………………………………………………… 26

Parts View …………………………………………………………………………………………………………………… 27

Page 2

28092-0-1110

Quick Start Guide
To START the Fireplace: If the pilot is NOT lit: 1. At the same time, press the “OFF” and high flame buttons and release once there is an
audible “beep” sound. 2. The pilot will ignite on the sixth beep. You may hear a clicking sound around the same
time as that beep, this is normal. 3. There will be a total of 14 beeps. The main burner will ignite approximately 15 seconds
after the pilot. If the pilot IS lit. 1. To ignite the burner, press the high flame button (there will be a beep) for appoximately
5 seconds until there is a soft click, then release the button.
To ADJUST the Flame Height 1. Press and hold the upper right button for a higher flame. 2. Press and hold the lower right button for a lower flame. Note: If you hold the lower right
button for too long, the flames on the main burner will go out, but the ignitor will stay lit.
To SHUT OFF the Fireplace 1. To completely shut off the burner and ignitor, press and hold the “OFF” button until the
unit “beeps.” The flames will go on the burner out once any lingering gas is used up. 2. To shut off the burner but keep the ignitor on, push the low flame button (bottom right) for
10 seconds and then release.
FOR MORE INFORMATION, SEE OPERATION INSTRUCTIONS.
VFSE Remote Quick Start Instructions: Cut out this page and keep it near your remote.

28092-0-1110

Page 3

THIS PAGE INTENTIONALLY LEFT BLANK

Page 4

28092-0-1110

IMPOrTANT SAFeTy INFOrMATION

· An unvented room heater having an input rating of more than 6,000 Btu per hour shall not be installed in a bathroom
· An unvented room heater having an input rating of more than 10,000 Btu per hour shall not be installed in a bedroom or bathroom.
· Never burn solid fuels in a fireplace where a gas log set is installed.
· Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
· Do not place clothing or other flammable material on or near the appliance.
· Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition.
· Young children should be carefully supervised when they are in the same room as the appliance.
· This unit complies with ANSI Z21.11.2 Unvented Heaters and it also complies with ANSI Z21.60 Decorative Vented Appliances for Solid Fuel Burning Fireplaces. State or local codes may only allow operation of this appliance in a vented configuration. Check your state or local codes.
· Correct installation of logs, proper location of the heater and annual cleaning are necessary to avoid potential problems with sooting. Sooting, resulting from improper installation or operation, can settle on surfaces outside the fireplace.
· Avoid any drafts that could alter burner flame patterns. Do not allow fans to blow directly into the fireplace. Do not place a blower inside burn box area of firebox. Ceiling fans may create drafts that alter burner flame patterns. Sooting and improper burning will occur as a result of drafts.
· WARNING: Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner flame patterns.
· WARNING: Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater.
· Periodic examination and cleaning of the venting system of the solid-fuel burning fireplace, including frequency of such examination and cleaning, by a qualified agency.
· The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/ NFPA54.

· NOTE: Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that the control compartment, burners and circulating air passageways of the appliance be kept clean.
· Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance. Provide adequate combustion and ventilation air.
· The flow of combustion and ventilation air MUST NOT be obstructed.
· Provide adequate clearances around air openings into the combustion chamber and adequate accessibility clearance for servicing and proper operation. NEVER obstruct the front opening of the appliance.
· An unvented room heater intended for installation in a solid-fuel burning fireplace shall comply with the following instructions.
· A fireplace screen must be in place when the appliance is operating and, unless other provisions for combustion air are provided, the screen shall have an opening(s) for introduction of combustion air.
· Solid-fuels shall not be burned in a masonry or UL 127 factorybuilt fireplace in which an unvented room heater is installed.
· Any glass doors shall be fully opened when the appliance is in operation.
· Any outside air ducts and/or ash dumps in the fireplace shall be permanently closed at time of appliance installation.
· WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.
· WARNING: Before installing in a solid-fuel burning fireplace, the chimney flue and firebox must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner.

wArNING
When used without adequate combustion and ventilation air, heater may give off CARBON MONOXIDE, an odorless, poisonous gas.
Do not install heater until all necessary provisions are made for combustion and ventilation air. Consult the written instructions provided with the heater for information concerning combustion and ventilation air. In the absence of instructions, refer to the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and Ventilation, or applicable local codes.
This heater is equipped with a PILOT LIGHT SAFETY SYSTEM designed to turn off the heater if not enough fresh air is available.
DO NOT TAMPer wITH PILOT LIGHT SAFeTy SySTeM!
If heater shuts off, do not relight until you provide fresh air. If heater keeps shutting off, have it serviced. Keep burner and control compartment clean.

CARBON MONOXIDE POISONING MAY LEAD TO DEATH.
Early signs of carbon monoxide poisoning resemble the flu, with headache, dizziness and/or nausea. If you have these signs, heater may not be working properly. Get fresh air at once! Have heater serviced. Some people ­ pregnant women, persons with heart or lung disease, anemia, those under the influence of alcohol, those at high altitudes ­ are more affected by carbon monoxide than others. The pilot light safety system senses the depletion of oxygen at its location. If this heater is installed in a structure having a high vertical dimension, the possibility exists that the oxygen supply at the higher levels will be less than that at the heater. In this type of application, a fan to circulate the structure air will minimize this effect. The use of this fan will also improve the comfort level in the structure. When a fan is used to circulate air, it should be located so that the air flow is not directed at the burner.

28092-0-1110

Page 5

SAFeTy INFOrMATION FOr uSerS OF LP-GAS

Propane (LP-Gas) is a flammable gas which can cause fires and explosions. In its natural state, propane is odorless and colorless. You may not know all the following safety precautions which can protect both you and your family from an accident. Read them carefully now, then review them point by point

with the members of your household. Someday when there may not be a minute to lose, everyone’s safety will depend on knowing exactly what to do. If, after reading the following information, you feel you still need more information, please contact your gas supplier.

LP-GAS wArNING ODOr
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas. That’s your signal to go into immediate action!

· Do not operate electric switches, light matches, use your phone. Do not do anything that could ignite the gas.
· Get everyone out of the building, vehicle, trailer, or area. Do that IMMEDIATELY.
· Close all gas tank or cylinder supply valves. · LP-Gas is heavier than air and may settle in low areas such
as basements. When you have reason to suspect a gas leak,
keep out of basements and other low areas. Stay out until
firefighters declare them to be safe. · Use your neighbor’s phone and call a trained LP-Gas service

person and the fire department. Even though you may not continue to smell gas, do not turn on the gas again. Do not re-enter the building, vehicle, trailer, or area. · Finally, let the service man and firefighters check for escaped gas. Have them air out the area before you return. Properly trained LP-Gas service people should repair the leak, then check and relight the gas appliance for you.

NO ODOr DeTecTeD – ODOr FADe

Some people cannot smell well. Some people cannot smell the odor of the chemical put into the gas. You must find out if you can smell the odorant in propane. Smoking can decrease your ability to smell. Being around an odor for a time can affect your sensitivity or ability to detect that odor. Sometimes other odors in the area mask the gas odor. People may not smell the gas odor or their minds are on something else. Thinking about smelling a gas odor can make it easier to smell.
The odorant in LP-gas is colorless, and it can fade under some circumstances. For example, if there is an underground leak, the movement of the gas through soil can filter the odorant. Odorants in LP-Gas also are subject to oxidation. This fading can occur if

there is rust inside the storage tank or in iron gas pipes.
The odorant in escaped gas can adsorb or absorb onto or into walls, masonry and other materials and fabrics in a room. That will take some of the odorant out of the gas, reducing its odor intensity.
LP-Gas may stratify in a closed area, and the odor intensity could vary at different levels. Since it is heavier than air, there may be more odor at lower levels. Always be sensitive to the slightest gas odor. If you detect any odor, treat it as a serious leak. Immediately go into action as instructed earlier.

SOMe POINTS TO reMeMBer

· Learn to recognize the odor of LP-gas. Your local LP-Gas Dealer can give you a “Scratch and Sniff” pamphlet. Use it to
find out what the propane odor smells like. If you suspect that your LP-Gas has a weak or abnormal odor, call your LP-Gas
Dealer.

cause odor fade. If such conditions are suspected to exist,
a periodic sniff test of the gas is advisable. If you have any question about the gas odor, call your LP-gas dealer. A periodic sniff test of the LP-gas is a good safety measure under any condition.

· If you are not qualified, do not light pilot lights, perform service, or make adjustments to appliances on the LP-Gas system. If you are qualified, consciously think about the odor of LP-Gas prior to and while lighting pilot lights or performing service or making adjustments.
· Sometimes a basement or a closed-up house has a musty smell that can cover up the LP-Gas odor. Do not try to light pilot lights, perform service, or make adjustments in an area where the conditions are such that you may not detect the odor if there has been a leak of LP-Gas.
· Odor fade, due to oxidation by rust or adsorption on walls of new cylinders and tanks, is possible. Therefore, people should be particularly alert and careful when new tanks or cylinders are placed in service. Odor fade can occur in new tanks, or reinstalled old tanks, if they are filled and allowed to set too long before refilling. Cylinders and tanks which have been out of service for a time may develop internal rust which will

· If, at any time, you do not smell the LP-Gas odorant and you think you should, assume you have a leak. Then take the same immediate action recommended above for the occasion when you do detect the odorized LP-Gas.
· If you experience a complete “gas out,” (the container is under no vapor pressure), turn the tank valve off immediately. If the container valve is left on, the container may draw in some air through openings such as pilot light orifices. If this occurs, some new internal rusting could occur. If the valve is left open, then treat the container as a new tank. Always be sure your container is under vapor pressure by turning it off at the container before it goes completely empty or having it refilled before it is completely empty.

Page 6

28092-0-1110

reQuIreMeNTS FOr cANADA

This unit cannot be installed in a UNVENTED application, this unit can only be installed as a VENTED application with these requirements.
IMPOrTANT SAFeTy INFOrMATION
This unit complies with ANSI Z21.60and CGA 2.26 Decorative Gas Appliances For Installation In Solid Fuel Burning Fireplaces. Do not burn wood or solid fuels in a fireplace where a decorative gas log set is installed. This appliance is for installation only in a solid fuel burning fireplace, masonry fireplace or manufactured fireplace.
warning: Any modification to this gas log set or to controls can be dangerous. Improper installation or use of the gas log set can cause serious injury or death from fire, burns, explosion or carbon monoxide poisoning.
1. Please follow all local codes regarding installation, combustion and ventilation air or in the absence of local codes follow the National Fuel Gas Code ANSI Z223.1(U.S. installation), or CAN/CGA-B149, Installation Code (Canada installation).
2. Proper installation, burner pan location and log placement is important to achieve optimum look and performance of your gas log set. The logs have been designed for easy location and placement on the grate and must be followed for proper operation.
3. Do not operate this log set with glass doors in the closed position. A fireplace screen must be in place when the log set is burning. Adequate combustion air must be provided for proper venting. All flames should go up and out the top of the firebox into the flue vent. If any flames float or curl forward into the room do not operate appliance. Check for an open flue and adequate combustion air into the room. A damper clamp must be installed on the firebox damper to maintain an open flue vent condition. Refer to page 14 INSTALLING DAMPER CLAMP
4. Young children must be carefully supervised when they are in the same room as the gas log while in operation. Do not place stockings, clothing or any flammable material above or near the fireplace.
5. Do not substitute or use materials other than those supplied for use with the log set.
6. Also refer to IMPORTANT SAFETY INFORMATION on page 5 of this manual

WARNING; DO NOT OPERATE THIS GAS LOG SET WITH GLASS DOOrS cLOSeD
· Clothing or other flammable material should not be placed on or near the appliance.
· Do not place trash or other articles on the log set during operation.
· During manufacturing, fabricating and shipping, various components of this appliance are treated with certain oils, films or bonding agents. These bonding agents are not harmful but
may produce annoying smoke and smells as they are burned
off during initial operation of the appliance. This is a normal
temporary occurrence. A window should be opened during the
initial bake out period. · Keep burner and control compartment clean. · wArNING: Before installing in a solid fuel burning fireplace,
the chimney flue and firebox must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner. · Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting,
bedding materials, etc. It is imperative that control compart-
ments, burners and circulating air passageways of the appli-
ance be kept clean. · Do not put anything around the fireplace that will obstruct the
flow of ventilation air. · Do keep the appliance area clear and free from combustible
material, gasoline and other flammable vapors and liquids. · A yearly examination and cleaning of the venting system of
the solid-fuel burning fireplace must be performed by a qualified agency. · Do make a periodic visual check of pilot and burners. Clean and replace damaged parts. · Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and
any gas control which has been under water. · Never burn solid fuels in fireplace where a gas log set is in-
stalled. · This unit complies with ANSI Z21.60 Decorative Vented Appli-
ances for Solid Fuel Burning Fireplaces. State or local codes may only allow operation of this appliance in a vented configuration. Check your state or local codes.

28092-0-1110

Page 7

INTrODucTION

IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty. Save this manual for future reference. Please read this manual before installing and using the appliance. Instructions to Installer 1. Installer must leave instruction manual with owner after
installation. 2. Installer must have owner fill out and mail warranty card supplied
with unvented room heater/vented decorative appliance.
3. Installer should show owner how to start and operate unvented room heater/vented decorative appliance.
Always consult your local Building Department regarding regulations, codes or ordinances which apply to the installation of an unvented room heater/vented decorative appliance.
This appliance may be installed in an aftermarket manufactured (mobile) home, where not prohibited by state or local codes.
Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.
New Installation Solid-fuels shall not be burned in a fireplace where a vented decorative appliance is installed.
A vented decorative appliance must be installed only in a solidfuel burning fireplace with a working flue and constructed of noncombustible material.
Any alteration of the original design, installed other than as shown in these instructions or use with a type of gas not shown on the rating plate is the responsibility of the person and company making the change.

Important All correspondence should refer to complete Model Number, Serial Number and type of gas.
Attention: During initial use of log you will detect an odor as the log is cured. Notice: During initial firing of this unit, its paint will bake out, and smoke will occur. To prevent triggering of smoke alarms, ventilate the room in which the unit is installed.
wArNING: This appliance is for installation only in a solid-fuel burning masonry or UL 127 factory-built fireplace or in a listed ventless firebox enclosure. It has been design certified for these installations. Exception: DO NOT install this appliance in a factory-built fireplace that includes instructions stating it has not been tested or should not be used with unvented gas logs.
WARNING: Any modification to this unvented gas heater or its controls can be dangerous. Improper installation or use of the heater can cause serious injury or death from fire, burns, explosion or carbon monoxide poisoning.
Well Head Gas Installations Some natural gas utilities use “well head” gas. This may affect the Btu output of the unit. Contact the gas company for the heating value. Contact the manufacturer or your gas company before changing spud/orifice size.

AcceSSOrIeS

Accessory Description

For use with VFSE and VFSV models

EK-1

Embers Kit

Color

ELH-1

Fireplace Hood for Vent-Free Logs

Black

ELH-2

Fireplace Hood for Vent-Free Logs

Brass

For use with VFSE models ONLY

AD1106V AC/DC Adapter

Note: Thermostats are for Vent-Free Applications only.

Page 8

28092-0-1110

PrODucT SPecIFIcATIONS

Regulator pressure setting Gas inlet pressure Max.
Min.

Natural Gas

VFSe

VFSV

3.5″ W.C.

4.0″ W.C.

10.5″ W.C.

10.5″ W.C.

7.0″ W.C.

7.0″ W.C.

Propane Gas

VFSe

VFSV

10.0″ W.C.

10.0″ W.C.

13.0″ W.C.

13.0″ W.C.

11.0″ W.C.

11.0″ W.C.

Model VFSE-18

Gas Natural

Valve Type Intermittent

VFSE-18

Propane

Intermittent

VFSE-24

Natural

Intermittent

VFSE-24

Propane

Intermittent

VFSE-30

Natural

Intermittent

VFSE-30

Propane

Intermittent

VFSV-16

Natural

Variable

VFSV-16

Propane

Variable

VFSV-18

Natural

Variable

VFSV-18

Propane

Variable

VFSV-24

Natural

Variable

VFSV-24

Propane

Variable

VFSV-30

Natural

Variable

VFSV-30

Propane

Variable

Note: Thermostats are for Vent-Free Applications only.

BTUH Max. Rate 32,000 32,000 36,000 36,000 38,000 38,000 25,000 22,500 32,000 32,000 36,000 36,000 38,000 38,000

BTUH Med. Rate — — — — — — — — — — — — — —

BTUH Min. Rate 26,000 26,000 28,800 28,800 30,000 30,000 18,000 17,000 21,000 21,000 24,000 24,000 27,000 27,000

28092-0-1110

Page 9

GeNerAL INFOrMATION

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided.
Keep room area clear and free from combustible materials, gasoline and other flammable vapors and liquids. Unvented gas heaters are a supplemental zone heater. They are not intended to be a primary heating appliance. Water vapor produced by an unvented heater can create moisture problems in a home when operated for extended periods of time.
During manufacturing, fabricating and shipping, various components of this appliance are treated with certain oils, films or bonding agents. These chemicals are not harmful but may produce annoying smoke and smells as they are burned off during the initial operation of the appliance; possibly causing headaches or eye or lung irritation. This is a normal and temporary occurrence.
The initial break-in operation should last 2 to 3 hours with the burner at the highest setting. Provide maximum ventilation by opening windows or doors to allow odors to dissipate. Any odors remaining after this initial break-in period will be slight and will disappear with continued use.
This appliance must not be used with glass doors in the closed position. This can lead to pilot outages and severe sooting outside the fireplace. Do not use this room heater if any part has been under water. Immediately call a qualified service technician to inspect the room heater and replace any part of the control system and any gas control which has been under water.
wArNING: This appliance is equipped for (natural or propane) gas. Field conversion is not permitted.
Before you get started Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately inform the dealer from whom you purchased the appliance. Do not attempt to install any part of the appliance unless you have all parts in good condition.
Make sure you have received all parts: Check your packing list to verify that all listed parts have been received. You should have the following: · Gas log grate/burner assembly. · Two (2) masonry anchoring screws and two (2) 10 x 1/2″ black
sheet metal anchoring screws. · Plastic bag containing glowing embers (rock wool) for burner
coverage. · Plastic bag containing lava rock. · Remote Kit

Handle the gas log burner assembly by the grate and legs only. Do not pick the unit up by the burner.
Gloves are recommended when handling logs to prevent skin irritation. Logs are fragile – Handle with care.
Qualified Installing Agency Installation and replacement of gas piping, gas utilization equipment or accessories and repair and servicing of equipment shall be performed only by a qualified agency. The term “qualified agency” means any individual, firm, corporation, or company that either in person or through a representative is engaged in and is responsible for (a) the installation, testing, or replacement of gas piping or (b) the connection, installation, testing, repair, or servicing of equipment; that is experienced in such work; that is familiar with all precautions required, and that has complied with all the requirements of the authority having jurisdiction.
State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts.
Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a copy of 527 CMR-30 upon sale of the unit.
The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1. Available from the American National Standards Institute, Inc. 11 West 42nd St., New York, N.Y. 10018.
High Altitudes: For altitudes/elevation above 2,000 feet ratings should be reduced at the rate of 4 percent for each 1,000 feet above sea level. Contact the manufacturer.

wATer VAPOr: A By-PrODucT OF uNVeNTeD rOOM HeATerS

Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one (1) ounce (30ml) of water for every 1,000 BTU’s (.3KW’s) of gas input per hour.
Unvented room heaters must be used as supplemental heat (a room) rather than a primary heat source (an entire house). In most supplemental heat applications, the water vapor does not create a problem. In most applications, the water vapor enhances the low humidity atmosphere experienced during cold weather.

The following steps will help insure that water vapor does not become a problem.
1. Be sure the heater is sized properly for the application, including ample combustion air and circulation air.
2. If high humidity is experienced, a dehumidifier may be used to help lower the water vapor content of the air.
3. Do not use an unvented room heater as the primary heat source (an entire house).

Page 10

28092-0-1110

PrOVISIONS FOr ADeQuATe cOMBuSTION & VeNTILATION AIr

This heater shall not be installed in a confined space unless provisions are provided for adequate combustion and ventilation air.
A confined space is an area with volume less than 50 cubic feet per 1,000 Btuh of the combined input rates of all appliances drawing combustion air from that space. Small areas such as equipment rooms are confined spaces. Furnaces installed in a confined space which supply heated air to areas outside the space must draw return air from outside the space through tightly sealed return air ducts. A confined space must have 2 openings into the space for combustion air. One opening must be within 12 inches of the ceiling and the other must be within 12 inches of the floor. The required sizing of these openings is determined by whether inside or outside air is used to support combustion, the method by which the air is brought to the space (vertical or horizontal duct) and by the total input rate of all appliances in the space.
Unusually Tight Construction The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.
Unusually tight construction is defined as construction where: a. Walls and ceilings exposed to the outside atmosphere have
a continuous water vapor retarder with a rating of one perm or less with openings gasketed or sealed, and b. Weatherstripping has been added on openable windows and doors, and c. Caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings. If your home meets all of the three criteria above, you must provide additional fresh air.
Warning: If the area in which the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and

FIREPLACE

DIVIDER

H L2

W

L1

ventilation air by one of the methods described in the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and Ventilation, or applicable local codes.

Example of Large Room with 1/2 Wall divider.

Figure 1

The following formula can be used to determine the maximum heater rating per the definition of unconfined space:

Btu/Hr = (L1 + L2)FT x (W)FT x (H)FT x 1000 50
If the area in which the heater may be operated is smaller than that defined as an unconfined space, provide adequate combustion and ventilation air by one of the methods described in the National Fuel
Gas Code, ANSI Z223.1, NFPA54.

Adhere to all codes, or in their absence, the latest edition of THE NATIONAL FUEL GAS CODE ANSI Z223.1/NFPA54 which can be obtained from:

American National Standards InstituteNational Fire Protection As-

sociation, Inc.

11 West 42nd St.

Batterymarch Park

New York, NY 10018

Quincy, MA 02269

cLeArANceS

Minimum Dimensions For Solid Fuel Burning Fireplaces UL127 Factory Built Fireplaces (Figure 2)

Model

A

B

c

D

VFSE-18

17″

14″

28″

17″

VFSE-24

23″

14″

30″

18″

VFSE-30

26″

14″

34″

20″

VFSV-16

18″

11 1/2″

24″

18″

VFSV-18

17″

14″

28″

17″

VFSV-24

23″

14″

30″

18″

VFSV-30

26″

14″

34″

20″

The dimensions shown and defined in the fireplace manufacturer’s instructions are minimum clearances to maintain in installing this heater. Left and right clearances are determined when facing the front of the heater.

Glass Doors Make sure that glass doors are open during all operations of
the logset. The opening of the glass door frame should be the dimension used for the minimum front opening of the firebox.

Follow these instructions to ensure safe installation. Failure to follow instructions exactly can create a fire hazard.
Figure 2

28092-0-1110

Page 11

CLEARANCES (continued)

Sidewall & Ceiling Clearances (Figure 3)
Figure 3 The sides of the fireplace opening must be 6″ from any combustible wall. The ceiling must be at least 36″ (for the 16″ log) and 41″ (for 18″, 24″ and 30″ logs) from the fireplace opening. Mantel Clearances Without Hood (Figure 4) You must have noncombustible materials above the fireplace opening. Noncombustible material must extend at least 12″ above fireplace opening. With sheet metal, you must have noncombustible material behind it. Heat resistant materials such as slate and marble must be at least 1/2″ thick. Sheet metal should not be installed onto combustible material.

N o n c o m b u s t i b l e Requirements for Safe Installation Material Distance

12″ or more

Noncombustible material

Less than 12″

Noncombustible material must be extended to at least 8″ with the installation of the optional fireplace hood. If you cannot extend noncombustible material at least 8″, you must operate heater with flue damper open.

Mantel Clearances with Hood (Figure 5) You must have noncombustible materials above the fireplace opening. Noncombustible material must extend at least 8″ above fireplace opening. With sheet metal, you must have noncombustible material behind it.
Heat resistant materials such as slate and marble must be at least 1/2″ thick. Sheet metal should not be installed onto combustible material.
Example: A mantel may project from the wall a maximum of 2″ at a minimum of 13 1/2″ above the opening, and a maximum of 6″ at a minimum of 15″ above the opening.

Figure 4 If your installation does not meet the above clearances, you must proceed to one of the following steps: · Use a hood · Operate the heater with flue damper open. See page 14 for
Installing as a Vented Appliance. · Raise the mantel to the proper height. · Remove the mantel.
Page 12

Figure 5
If your installation does not meet the above minimum clearances, you must proceed to one of the following steps: · Operate the heater with the flue damper open. See page 14
for Installing as a Vented Appliance. · Raise the mantel to the proper height. · Remove the mantel.
Floor Clearance (Figure 6) If installing heater at floor level, the minimum distance to combustibles is “0” inches.

HEATER IN FIREPLACE OR FIREBOX

COMBUSTIBLE MATERIAL
Figure 6

28092-0-1110

cOMBuSTIBLe MATerIAL

Do not attach combustible material to the mantel of your fireplace. This is a fire hazard.

No greeting card, stockings or ornamentation of any type should be
placed on or attached to the fireplace. This is a heating appliance. The flow of heat can ignite combustibles.

Figure 7

Figure 8

FIrePLAce PrePArATION

· Turn off gas supply to fireplace or firebox. · Have the fireplace floor and chimney professionally cleaned to
remove ashes, soot, creosote or other obstructions.
Have this cleaning performed annually after installation.
· Seal any fresh air vents or ash clean-out doors located on floor or wall of fireplace. If not, drafting may cause pilot outage or sooting. Use a heat- resistant sealant. Do not seal
chimney flue damper. Install and operate the appliance as directed in this manual.

FOr FAcTOry BuILT FIrePLAceS Free OPeNING AreA OF cHIMNey DAMPer FOr VeNTING cOMBuSTION PrODucTS FrOM DecOrATIVe APPLIANceS FOr INSTALLATION IN SOLID FueL BurNING FIrePLAceS
Appliance Input Rate (BTU/hr)

20

30

40

Chimney Height* (ft)

Minimum Opening** (sq. in.)

10

11.3

16.6

22.1

15

8.6

12.6

17.3

20

7.5

10.8

14.5

25

6.6

9.6

12.6

30

6.2

9.1

11.3

35

5.7

8.0

10.8

40

5.3

7.5

10.2

• Height is from hearth to top of chimney and the minimum height is 10 feet.
  ** Chart shows minimum opening (sq. in.) for given height and input rate.

28092-0-1110

FOr MASONry BuILT FIrePLAceS Free OPeNING AreA OF cHIMNey DAMPer FOr VeNTING cOMBuSTION PrODucTS FrOM DecOrATIVe APPLIANceS FOr INSTALLATION IN SOLID FueL BurNING FIrePLAceS

Appliance Input Rate (BTU/hr)

20

30

40

Chimney Height* (ft)
6

Minimum Opening** (sq. in.)

17.6

25.7

33.8

8

16.5

23.7

31.2

10

15.1

21.7

28.7

15

14.1

19.9

26.1

20

12.9

18.5

23.7

30

12.2

16.9

21.6

• Height is from hearth to top of chimney and the minimum height is 6 feet.
  ** Chart shows minimum opening (sq. in.) for given height and input rate.

Page 13

INSTALLING AS A VeNTeD APPLIANce

Notice: (Damper Clamp Installation) When installing your log set as a vented installation the damper
clamp must be used.

When installing your log set as a vent-free installation the damper clamp can be used to eliminate the potential for odors when burning the logs for the first time.
Installing Damper Clamp (Figure 9) Remove all ashes or other debris from the fireplace. If the fireplace is equipped with an ash dump be sure to seal the door with furnace cement or high temperature silicone. Be sure to check the damper for proper operation and verify that the flue passageway is open.
Place the clamp over the lip of the damper and tighten the hold down bolt until the clamp is securely attached to the damper. This will prevent the damper from accidentally closing.
Manual and millivolt controlled gas logs may be installed as a vented decorative log set in compliance with ANSI Z21.60 and National Fuel Gas Code. When the gas logs are operated with the damper open, noncombustible material and minimum mantel requirements do not apply.

Figure 9

BeFOre FuLLy INSTALLING THe APPLIANce

· Turn off the gas supply to the fireplace or firebox. · Seal any fresh air vents and/or ash clean-out doors located on
the floor or wall of the fireplace. If left unsealed, drafting may cause pilot outage or sooting. Use a heat resistant sealant. Do
not seal the chimney flue damper.
Before installing in a solid fuel burning fireplace, the chimney flue and firebox must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner.
You must secure the gas log heater to the fireplace floor. If not, the entire unit may move when you adjust the controls. Movement of unit may cause shifting of the gas logs which leads to sooting and improper burning. Grate movement could cause a gas leak.
Special care is required if you are installing the unit into a sunken fireplace. You must raise the fireplace floor to allow access to gas log controls. This will insure adequate air flow and guard against sooting. Raise the fireplace floor using noncombustible materials.

Assembly Procedure: (Figure 10) 1. Center the gas log unit in the fireplace or firebox. Make certain
the front feet of the grate sit inside the front edge of the fireplace or firebox. 2. An anchor hole is provided in the two bottom side members of
the grate frame. After centering the grate correctly, mark the hole positions on the fireplace/firebox floor. Drill two (2) 5/32″ diameter holes approximately 1 1/2″ deep for masonry screws
or 1/8″ hole for sheet metal screws. 3. Anchor the grate to the fireplace/firebox floor using the screws
provided. Refer to Figure10.
Proper installation of the grate is essential to prevent any movement of the gas logs and controls during operation.

Page 14

Figure 10

28092-0-1110

GAS SuPPLy

Check all local codes for requirements, especially for the size and type of gas supply line required.

Recommended Gas Pipe Diameter

Pipe Length Schedule 40 Pipe Tubing, Type L Inside Diameter Outside Diameter

Nat.

L.P.

Nat.

L.P.

0-10 feet

1/2″

3/8″

1/2″

3/8″

0-3 meters 12.7mm 9.5mm 12.7mm 9.5mm

10-40 feet

1/2″

1/2″

5/8″

1/2″

4-12 meters 12.7mm 12.7mm 15.9mm 12.7mm

40-100 feet 1/2″

1/2″

3/4″

1/2″

13-30 meters 12.7mm 12.7mm 19mm 12.7mm

100-150 feet 3/4″

1/2″

7/8″

3/4″

31-46 meters 19mm 12.7mm 22.2mm 19mm

Note: Never use plastic pipe. Check to confirm whether your local codes allow copper tubing or galvanized.
Note: Since some municipalities have additional local codes, it is always best to consult your local authority and installation code.
Installing a New Main Gas Cock Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of the unit. Where none exists, or where its size or location is not adequate, contact your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant to the action of liquefied petroleum gases. The gas lines must be checked for leaks by the installer. This should be done with a soap solution watching for bubbles on all exposed connections, and if unexposed, a pressure test should be made.
Never use an exposed flame to check for leaks. Appliance must be disconnected from piping at inlet of control valve and pipe capped or plugged for pressure test. Never pressure test with appliance connected; control valve will sustain damage!
A gas valve and ground joint union should be installed in the gas line upstream of the gas control to aid in servicing. It is required by the National Fuel Gas Code that a drip line be installed near the gas inlet. This should consist of a vertical length of pipe tee connected into the gas line that is capped on the bottom in which condensation and foreign particles may collect.

Figure 11
The use of the following gas connectors is recommended: — ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing
and Fittings — ANS Z21.45 Assembled Flexible Appliance Connectors of Other
Than All-Metal Construction
The above connectors may be used if acceptable by the authority having jurisdiction. The state of Massachusetts requires that a flexible appliance connector cannot exceed three feet in length.
Pressure Testing of the Gas Supply System 1. To check the inlet pressure to the gas valve, a 1/8″ (3.175mm)
N.P.T. plugged tapping, accessible for test gauge connection, must be placed immediately upstream of the gas supply connection to the appliance. 2. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). 3. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).
Attention! If one of the procedures results in pressures in excess of 1/2 psig (14″ w.c.) (3.5 kPa) on the appliance gas valve, it will result in a hazardous condition.

28092-0-1110

Page 15

PLACEMENT OF GLOWING EMBERS AND LAVA ROCK

Placement of the glowing embers (rock wool) is very individual and light coverage will provide your best effects. We recommend separation of the rock wool by hand and make your coverage as light and fluffy as possible.
Place just enough embers on the burner to obtain the glow and a gold, yellow flame.
Do not place embers (rock wool) over large ports in rear portion of burner.
Rock wool should not be placed in the area of the pilot assembly.
Replacement of loose material (glowing embers) must be purchased from Empire Comfort Systems, Inc. Application of excess loose material (glowing embers) may adversely affect performance of the heater. WARNING: All previously applied loose material must be removed prior to reapplication.
Refer to Parts List, Page 26 to order loose material (rock wool).

Placing Lava Rock in Front of Burner on Fireplace Floor
Spread lava rocks on fireplace floor in front of the burner pan. The lava rocks are for decorative effect and are not required for fireplace operation.
ATTeNTION: DO NOT PLACE LAVA ROCKS ON BURNER, LOGS OR ROCK WOOL. THE LAVA ROCKS SHOULD ONLY BE PLACED ON THE FIREPLACE FLOOR.

OPerATION INSTrucTIONS/FLAMe APPeArANce

Flames from the pilot (rear right back side of the pan burner) as well as the main flame should be visually checked as the log set is installed.
In normal operation at full rate after 10 to 15 minutes, the flame appearance should be sets of yellow flames.
NOTe: All flames will be random by design, flame height will go up and down.
Glowing embers (rock wool) can cover the pan burner in between the front and middle logs, but very little is necessary to cover this area. Excess ember material causes the yellow flame to become orange and stringy. Apply just enough to obtain slow glow and a gold yellow flame.
Avoid any drafts that alter burner flame patterns. Do not allow fans to blow directly into fireplace. Do not place a blower inside the burner area of the firebox. Ceiling fans may create drafts that alter flame patterns. Sooting and improper burning will result.
During manufacturing, fabricating and shipping, various components of this appliance are treated with certain oils, films or bonding agents. These chemicals are not harmful, but may produce annoying smoke and smells as they are burned off during the initial operation of the appliance, possibly causing headaches or eye or lung irritation. This is a normal and temporary occurrence.
The initial break-in operation should last 2 to 3 hours with the burner at the highest setting. Provide maximum ventilation by opening windows or doors to allow odors to dissipate. Any odors remaining after this initial break-in will be slight and will disappear with continued use.

Intermittent – Figure 12 Variable – Figure 13

Page 16

28092-0-1110

G6R-P3TAN5 REMOTE CONTROL INSTRUCTIONS
NOTe: This remote is for use on VFSE Models ONLY.
AuTOMATIc OPerATION

GeNerAL NOTeS
Radio Frequency Remote 433.92 MHz for Europe; 315 MHz for U.S. (FCC ID: RTD- G6R) and for Canada (IC: 4943A-G6R).
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Batteries – Remote Handset: 1 x 9V block (quality alkaline recommended)
Batteries – Receiver: 4 x 1.5V “AA” (quality alkaline recommended)
An AC Mains Adapter may be used instead of batteries (only the Mertik Maxitrol or an AC Mains Adapter approved by Mertik Maxitrol can be used).
NOTe: During a power outage the AC Mains Adapter muts be unplugged from the receiver to operate in the battery mode.

wArNING Wiring of valve and receiver must be completed before starting ignition. Failure to do so could damage the electronics.
NOTe: This remote handset and receiver are not interchangeable with previous versions. For all lighting/ignition instructions please refer to appliance manufacturer’s instructions.
SeTTING THe eLecTrONIcS cODe Radio Frequency Remote A code is selected automatically for all Mertik Maxitrol electronics from among 65,000 random codes available. The receiver has to learn the code of the handset: · Press and hold the receiver’s reset button until you hear two
(2) acoustic signals. After the second, longer acoustic signal, release the reset button. · Within the subsequent 20 seconds press the small flame) button on the remote handset until you hear an additional long signal confirming the code is set.
NOTe: This is a one time setting only, and is not required when changing the batteries in the remote or receiver.
TO TurN ON APPLIANce
wArNING
When pilot ignition is confirmed, motor turns automatically to maximum flame height. · Turn MANUAL knob to the ON, full counterclockwise
position. · Place ON/OFF switch (if equipped in (ON position).

28092-0-1110

Page 17

G6R-P3TAN5 REMOTE CONTROL INSTRUCTIONS

Standard, Display, Timer/Thermostat RF Remote Handset · Simultaneously press and hold the OFF and (large flame)
buttons until a short acoustic signal confirms the start sequence has begun; release buttons. · Continuing signals confirm the ignition is in process. · Once pilot ignition is confirmed, there is main gas flow. · After the ignition the remote will go automatically into temperature control mode (CSA-versions) or manual mode (CE-versions)
TO TurN OFF THe APPLIANce
Press OFF button on remote handset. NOTE: Press (small flame) to turn main gas to pilot gas.
TO OPeN AND cLOSe SOLeNOID VALVe/BurNer
NOTe: The latching solenoid valve will not operate for one minute after ignition. The latching solenoid valve cannot operate manually. If the battery runs down it will remain in the last operating position. During normal operation the solenoid valve will be reset into the ON position when the GV60 is switched OFF remotely.
· Upon ignition both Burner and Decorative Burner are ON. · Press upper left and lower right button simultaneously to
switch the Burner OFF (printed instructions are located on the battery cover). · Press upper left and upper right button simultaneously to switch the Burner ON. (Display and Timer/Thermostat Remote Handsets: the AUX symbol on the display will indicated that the solenoid valve is OPEN.)
ADJUSTMENT – FLAME HEIGHT Standard, Display, Timer/Thermostat RF Remote Handsets · In standby mode: Press (large flame) to increase flame
height. · Press (small flame) to decrease flame height or to set
appliance at pilot flame. · For fine adjustment tap the large/small flames.

SETTING °C/24 HOUR OR °F/12 HOUR CLOCK
Display, Timer/Thermostat RF Remote Handsets · Press OFF and (small flame) until display changes from
Fahrenheit/12 hour clock to Celsius/24 hour clock and vice versa.

SeTTING THe TIMe
Display, Timer/Thermostat Remote Handsets · This display will flash after either:
a. Installing the battery or b. Simultaneously pressing the (large flame) and (small flame). · Press (large flame) to set the hour and the (small flame) to set the minute. · Press OFF to return to manual mode or simply wait and it will automatically return to the manual mode.
Remaining Instructions pertain to Timer/Thermostat RF Remote Handset only

cHANGING THe MODe OF OPerATION Briefly pressing the SET button changes the mode of operation in the following order:

MAN

TEMP

TEMP TIMER and back to MAN

NOTe: MANUAL mode can also be reached by pressing either the (large flame) or the (small flame).

MAN Mode – Manual Flame Height Adjustment · Press (large flame) to turn on the main burner. · Press (large flame) to increase the flame height. · Press (small flame) to decrease the flame height or to go to
pilot standby position.
NOTe: While pressing either button a symbol indicating transmission appears on the display. The receiver confirms transmission with an acoustic signal.
TEMP – Daytime Temperature Mode (appliance must be in standby mode; pilot ignited): The room temperature is measured and compared to the set temperature. The flame height is then automatically adjusted to achieve the Daytime set temperature.

TEMP – Nighttime Setback Temperature Mode (appliance must be in standby mode; pilot ignited): The room temperature is measured and compared to the Nighttime Setback temperature. The flame height is then automatically adjusted to achieve the Nighttime Setback temperature.
TIMER – Timer Mode (appliance must be in standby mode; pilot ignited):
The Timer setting allows you to set two (2) burner TEMP times every 24 hours.
For TEMP to operate as a thermostat, TEMP must be set at 40°F (4°C) or higher.

Page 18

28092-0-1110

G6R-P3TAN5 REMOTE CONTROL INSTRUCTIONS

If the TEMP setting is decreased to –, the motor will turn the valve to the standby position in the moon times and await the next burner TEMP cycle.
NOTE: The display shows the set temperature every 30 seconds.

SeTTING THe TeMPerATure
· Select either the TEMP MODE or the TEMP MODE by briefly pressing the SET button.
· Hold the SET button until the TEMP display flashes. · Set the desired temperature with (large flame) or (small
flame). · Press OFF or simply wait to complete programming.

SeTTING THe TIMer
· Select Timer mode by briefly pressing the SET button.
· Press and hold the SET button until the P1 (sun symbol) is displayed) and the time flashes. Set the hour by pressing the (large flame) and set the minutes by pressing the (small flame).
· Briefly press SET button for the next burner cycle time.
· Example: P2 (moon symbol) continue through P2
(sun symbol) and P2 (moon symbol). · Once all four (4) times are set, press OFF or simply wait to
complete programming.

MANuAL OPerATION

(Only possible when MANUAL knob is used)

Follow appliance manufacturer’s instructions for gaining access to the gas control and the pilot burner. Access to the pilot burner is

only required for ignition with a match.

When turning main valve knob, do not force. Knob has a slip clutch

that clicks until the end stops are reached. This allows for manual

flame height adjustment as well as adjustment to pilot standby po-

sition.

1. STOP! Read the safety information included before proceed-

ing.

2. Turn main valve knob to the OFF, full clockwise

position.

3. Turn MANUAL knob to the MAN, full clockwise

posi-

tion.

4. Place ON/OFF switch (if equipped) in O (OFF position).

5. Wait five (5) minutes to clear out any gas. Verify that no gas

is in the area around the appliance, including near the floor. If

you detect gas STOP! Follow “A” in the safety information on page 20. If no gas is present, proceed to step 6.

6. Place ON/OFF switch (if equipped in (ON position).

7. With the MANUAL knob in MAN position a manual pilot valve

operator and piezo igniter (optional) are accessible.

8. Fully push down manual pilot valve operator and hold in, to start pilot gas flow. Ignition with match: Immediately light the pilot with a match, while continuing to hold in the manual pilot valve operator for about one (1) minute after the pilot is lit. Release manual pilot valve operator. If pilot does not stay lit, wait five (5) minutes and repeat. Ignition with piezo igniter: Change the ignition cable from the receiver to the valve. Use the push piezo igniter to ignite. If pilot does not stay lit, wait five (5) minutes and repeat. NOTE: If the pilot does not stay lit after several tries, turn the gas control knob (main valve knob) to OFF and proceed to step 11.
9. If applicable, per appliance manufacturer’s instructions, replace pilot access panel before proceeding.
10. Turn MANUAL knob to the ON, full counterclockwise
position. 11. Turn main valve knob to the full ON, full counterclockwise
position. 12. If the appliance will not operate, follow the instructions “TURN
OFF GAS TO APPLIANCE” and call the service technician or gas supplier.

TurN OFF GAS TO APPLIANce

· Press OFF button on remote or wall switch/touch pad/switch

panel.

· Follow appliance manufacturer’s instructions for gaining

accessibility to the gas control.

· Place ON/OFF switch (if equipped in O (off position).

· Turn main valve knob to the OFF full

clockwise

position.

· Replace appliance accessibility cover (if applicable), per

appliance manufacturer’s instructions.

MISceLLANeOuS
Low Battery Indication Receiver:
three short beeps will sound when motor turns Standard/Infrared remote:
the red LED will get darker Remote with display:
“BATT” will appear on display NOTe: Pertains to Thermostatic Display/Handsets: If the battery
of the handset is low or if the transmitter is out of the communication range, the motor turns down the valve to pilot gas after 6 hours. NOTe: With very low battery the GV60 system shuts off the fire completely. This will not happen if the power supply is interrupted.
Battery replacement Battery replacement is recommended at the beginning of each heating season. Pull ribbon to remove batteries. Do not use metal tools to remove batteries. Using a metal tool could cause a short that may damage the receiver.

28092-0-1110

Page 19

G6R-P3TAN5 REMOTE CONTROL INSTRUCTIONS

Location of Receiver When the RF-receiver is placed in the appliance, the surrounding metal can reduce reception considerably. The position of the antenna on the receiver also influences reception. It is recommended to straighten the antenna. The antenna must not come in contact or cross the ignition wire, this may render the receiver inoperable.
NOTe: To keep receiver free from debris, dirt, and humidity, do not remove the receiver from the plastic bag until all construction is complete.

MANUAL KNOB
PIEZO IGNITER CONNECTION FOR MANUAL IGNITION

MAIN VALVE KNOB

Piezo Igniter (optional) ON/OFF Switch (optional) in ON Position
8 Wire Receiver Jack
Microswitch
Cutout for Pilot Gas Adjustment

Connection Piezo Igniter Tab 2.8 x 0.8 mm
MANUAL Knob in MAN Position
Manual Pilot Valve Operator

COMBINATION CONTROL

THERMOCOUPLE

INTERRUPTER BLOCK

ON/OFF SWITCH
O I
THERMO CURRENT CABLE #2 OR ON/OFF SWITCH WITH SOLDERED CABLE

THERMO CURRENT CABLE #1

IGNITION CABLE RF ANTENNA

SPARK

SW TC

MA GR MO SW

PANEL

Main Valve Knob in OFF Position
MANUAL Knob in position for automatic ignition

BATTERY COMPARTMENT

BUTTON “RESET”

Wiring Diagram Figure 14

8 WIRE CABLE

Page 20

28092-0-1110

VFSE-(18,24,30) LIGHTING INSTRUCTIONS
FOr yOur SAFeTy reAD BeFOre LIGHTING
wArNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.
B. BeFOre LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
wHAT TO DO IF yOu SMeLL GAS · Do not try to light any appliance. · Do not touch any electrical switch;
do not use any phone in your building. · Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.

· If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it; call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

2. Open bottom louver assembly (if applicable).

3. Press the “I/O” (ON/OFF) button on the valve face to “OFF.”

4. Wait five (5) minutes to clear out any gas, then smell for gas

including near the floor. If you smell gas, STOP! Follow “B”

in the safety information above. If you don’t smell gas, go to

the next step.

LIGHTING PrOceDure – HANDSeT MeTHOD

1. Turn control arrow on valve face to “ON.” Press the “I/O” but-

ton to “I.” Press the “OFF” and “UP” buttons on the handset,

firmly at the same time. A long “Beep” will sound, followed by

5 short “beeps.” Ignitor will spark and will continue until pilot

is lit. For full Remote Control operation see Appliance Instal-

lation manual.

LIGHTING PrOceDure – MANuAL MeTHOD

1. Press the “I/O” (ON/OFF) button to “I.”

2. Turn control arrow on valve face to “MAN.”

3. Using a small bladed screwdriver, press and hold button

within hole on control. Manually depress piezo igniter button

to light pilot. If pilot does not light, steps 2 to 3 can be imme-

diately repeated. If the pilot will not stay lit after several tries,

follow the instructions “To Turn Off Gas to Appliance” and call

your service technician or gas supplier.

4. When the pilot is lit and stable, turn flame height control knob

counterclockwise

and the main burner will ignite.

To adjust flame height, turn flame height control knob.

“I/O” (ON/OFF) SWITCH

MAN
MAN

NO

TO IGNITE PILOT

HANDSET MODE
To Ignite Burner

MANUAL MODE
PIEZO IGNITER

O
75 F
SET

OFF

Press firmly at same time
PILOT ELECTRODE

PRESS IN & HOLD

PILOT ELECTRODE

THERMOCOUPLE (LPG)
THERMOCOUPLE (NATURAL)

THERMOCOUPLE (LPG)
THERMOCOUPLE (NATURAL)

CORRECT PILOT FLAME

INCORRECT PILOT FLAME

TO TURN OFF GAS TO APPLIANCE

MANuAL MODe – To turn off main burner, tun flame height

control knob fully clockwise

. To fully shut down, press

“I/O” button to “O.”

HANDSeT MODe – Press “OFF” button on handset. To fully shut down, press “I/O” button to “O.”

28092-0-1110

Page 21

VFSV-(16,18,24,30) LIGHTING INSTRUCTIONS FOr yOur SAFeTy reAD BeFOre LIGHTING

wArNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.
B. BeFOre LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
wHAT TO DO IF yOu SMeLL GAS
· Do not try to light any appliance. · Do not touch any electrical switch;
do not use any phone in your building. · Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions. · If you cannot reach your gas supplier, call the fire
department.

C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it; call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information on this page.

2. Push in gas control knob slight-

ly and turn clockwise

to “OFF.” Do not force.

3. Turn gas flow adjustment

knob clockwise

PIEZO IGNITOR

either manually or with remote

control to “OFF.”

4. Wait ten (10) minutes to clear out any gas. Then smell for

GAS CONTROL KNOB SHOWN IN “PILOT! POSITION.

gas, including near floor. If you

smell gas, STOP! Follow “B” in

the safety information above. If

you do not smell gas, go to the

next step.

5. Find pilot – follow metal tube

from gas control. The pilot is

behind the second log on the

right side.

6. Turn gas control knob coun-

terclockwise

to “PI-

LOT.”

7. Push in control knob all the way and hold in. Immediately

light the pilot with the piezo pilot ignitor or use a match. Con-

tinue to hold the control knob in for about one (1) minute after

the pilot is lit. Release knob, and it will pop back up. Pilot

should remain lit. If it goes out, repeat steps 5 through 8.

If knob does not pop up when released, stop and im-

mediately call a qualified service technician or gas sup-

plier.

If the pilot will not stay lit after several tries, turn the gas

control knob to “OFF” and call your service technician or gas

supplier.

8. Turn gas control knob counterclockwise

to off.

9. Turn on all electric power to the appliance (if applicable).

10. Set thermostat to desired setting.

TO TURN OFF GAS TO APPLIANCE

1. Turn gas flow adjustment knob clockwise manually or with remote control to “OFF”.

either

2. Push in gas control knob slightly and turn clockwise to “OFF”. Do not force.

Page 22

28092-0-1110

PILOT FLAMe cHArAcTerISTIcS

Figure 15 shows a correct pilot flame pattern. The correct flame will be blue and will extend beyond the thermocouple. The flame will surround the thermocouple just below the tip. A slight yellow flame may occur where the pilot flame and main burner flame meet. Figure 16 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down.
Cleaning and Maintenance/Pilot VFSV, VFSE PILOT

Cleaning and Maintenance/Pilot Oxygen Depletion Sensor Pilot (Figure 17) When the pilot has a large yellow tip flame, clean the Oxygen Depletion Sensor as follows: 1. Clean the ODS pilot by loosening nut B from the pilot tubing.
When this procedure is required, grasp nut A with an open end wrench. 2. Blow air pressure through the holes indicated by the arrows. This will blow out foreign materials such as dust, lint and spider webs. Tighten nut B also by grasping nut A.
Warning: Never use needles, wires, or similar cylindrical objects to clean the pilot to avoid damaging the calibrated ruby that controls the gas flow.

Correct Pilot Flame Pattern Figure 15

Figure 17

Incorrect Pilot Flame Pattern Figure 16
If pilot flame pattern is incorrect, as shown in Figure 16 · See Troubleshooting, page 25.
28092-0-1110

Page 23

cLeANING AND SerVIcING

Annual inspection and cleaning by your dealer or qualified service technician is recommended to prevent malfunction and/or sooting.
TurN OFF HeATer AND ALLOw TO cOOL BeFOre CLEANING. Remove logs, handling carefully by holding gently at each end. Gloves are recommended to prevent skin irritation from ceramic fibers. If skin becomes irritated, wash gently with soap and water. Refer to manual for correct log placement.
PERIODIC CLEANING ­ Refer to parts diagram for location of items discussed below. · Do not use cleaning fluid to clean logs or any part of heater. · Logs – brush with soft bristle brush or vacuum with brush
attachment. · Remove loose particles and dust from the burner areas,
controls, piezo covers and grate. Don’t remove media from inside burner box. · Inspect and clean burner air intake hole. Remove lint or particles with brush. Failure to keep air intake hole clean will result in sooting and poor combustion.

ANNUAL CLEANING/INSPECTION ­ Refer to parts diagram for location of items discussed below.
· Inspect and clean burner air intake hole. Remove lint or particles with vacuum or brush. Failure to keep air intake hole clean will result in sooting and poor combustion.
· Inspect and clean all burner ports. · Inspect ODS pilot for operation and accumulation of lint at air
intake holes. · Verify flame pattern and log placement for proper operation. · Verify smooth and responsive ignition of main burner. · Check level of ceramic media in burner. Burner should be full,
up to the level of openings in burner top.
VFSV Note: (Wiring harness located in envelope) Connect black/red 3/16″ terminal wire from receiver to 3/16″ terminal on valve. Connect black 1/4″ terminal wire from receiver to 1/4″ terminal on valve. Install remote receiver cover over receiver when receiver is installed into fireplace area. Locate receiver and cover to the right and forward of valve. (Do not put receiver behind logs).

MANUAL KNOB
PIEZO IGNITER CONNECTION FOR MANUAL IGNITION

wIrING
MAIN VALVE KNOB

COMBINATION CONTROL

THERMOCOUPLE

INTERRUPTER BLOCK

ON/OFF SWITCH
O I
THERMO CURRENT CABLE #2 OR ON/OFF SWITCH WITH SOLDERED CABLE

THERMO CURRENT CABLE #1

IGNITION CABLE RF ANTENNA

SPARK

SW TC

MA GR MO SW

THERMOCOUPLE (NATURAL)

ADJ.

LEARN

THERMOCOUPLE (LPG)

PANEL

Page 24

BATTERY COMPARTMENT
BUTTON “RESET”
VFSE Wiring Diagram

8 WIRE CABLE

OFF REMOTE

Figure 18

VFSV Wiring Diagram

28092-0-1110

TrOuBLeSHOOTING SyMPTOMS – POSSIBLe cAuSeS AND cOrrecTION

1. When ignitor button is pressed, there is no spark at ODS/ pilot. a. Ignitor electrode positioned wrong – Replace pilot. b. Ignitor electrode is broken – Replace pilot. c. Ignitor electrode not connected to ignitor cable – Reconnect ignitor cable. d. Ignitor cable pinched or wet. Keep ignitor cable dry – Free ignitor cable if pinched by any metal or tubing. e. Broken ignitor cable – Replace ignitor cable. f. Bad piezo ignitor – Replace piezo ignitor.
2. Appliance produces unwanted odors. a. Appliance burning vapors from paint, hair spray, glues, etc. – Ventilate room. Stop using odor causing products while heater is running. b. Gas leak – Locate and correct all leaks.
3. Appliance shuts off during use. (Pilot and main burner are off.) a. Not enough fresh air is available for ODS/pilot to operate Open window and/or door for ventilation. b. Low line pressure – Contact local gas company. c. ODS/pilot is partially clogged – Clean ODS/pilot. d. Defective thermocouple – Replace pilot.
4. Appliance shuts off during use. (Pilot stays on.) a. Low line pressure – Check line pressure to the valve.
5. Gas odor even when control knob is in OFF position. a. Gas leak – Locate and correct all leaks. b. Control valve defective – Replace control valve.
6. When ignitor button is pressed, there is spark at ODS/pilot, but no ignition. a. Gas supply turned off or manual shutoff valve closed – Turn on gas supply or open manual shutoff valve. b. Control knob not in PILOT position – Turn control knob to PILOT position. c. Control knob not pressed in while in PILOT position – Press in control knob while in PILOT position. d. Air in gas lines when installed – Continue holding down control knob. Repeat igniting operation until air is removed. e. ODS/pilot is clogged – Replace ODS/pilot assembly or get it serviced. g. Gas regulator setting is not correct – Replace gas regulator.
7. ODS/pilot lights but flame goes out when control knob is released. a. Control knob not fully pressed in – Press in control knob fully. b. Control knob not pressed in long enough – After ODS/pilot lights, keep control knob pressed in 30 seconds.

c. Manual Shutoff valve not fully open – Fully open manual
shutoff valve.
d. Thermocouple connection loose at control valve – Hand
tighten until snug, then tighten 1/4 turn more.
e. Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot flame to go out. This problem could be caused by either low gas pressure or dirty or
partially clogged ODS/pilot – Contact local gas company.
f. Thermocouple damaged – Replace thermocouple.
h. Control valve damaged – Replace control valve.
8. Burner does not light after ODS/pilot is lit. a. Burner orifice clogged – Clean burner or replace main burner orifice. b. Burner orifice diameter is too small – Replace burner orifice. c. Inlet gas pressure is too low – Contact qualified service person.
9. If burning at main burner orifice occurs (a loud, roaring blow torch noise). a. You must turn off burner assembly and contact a qualified service person.
b. Manifold pressure is too low – Contact local gas company.
c. Burner orifice clogged – Clean burner or replace burner orifice.
10. Logs appear to smoke after initial operation. a. Vapors from paint or curing process of logs – Problem will
stop after a few hours of operation. Run the heater with the
damper open if you have one, or open a window for the first few hours.
Log heater is intended to be smokeless. Turn OFF heater
and call qualified service person. 11. Heater produces a whistling noise when main burner is
lit. a. Turning control knob to HIGH position when main burner is
cold – Turn control knob to LOW position and let warm up
for a minute.
b. Air in gas line – Operate burner until air is removed from
line. Have gas line checked by local gas company.
c. Dirty or partially clogged burner orifice – Clean burner or replace burner orifice.
12. No gas to pilot. a. LP-regulator shut down due to inlet pressure too high –
Verify LP tank regulator is installed and set at 11″ to 13″
w.c. Replace regulator on heater.

If the gas quality is bad, your pilot may not stay lit, the burners may produce soot and the heater may backfire when lit. If the gas quality or pressure is low, contact your local gas supplier immediately.

28092-0-1110

Page 25

PArTS LIST

Attention: When ordering parts, it is very important that part number and description of part coincide.

INDEX NO.
1 1 1 1 2 3 5 5 6 6 7
9
9
9 9 9 NS NS NS NS NS NS
NS
4 4 4 4 4 4 8
10
11 11 12 13
NS
NS

PArT NO.

DeScrIPTION

cOMMON

15425 REAR LOG SUPPORT (16″ MODELS)

15426 REAR LOG SUPPORT (18″ MODELS)

15427 REAR LOG SUPPORT (24″ MODELS)

15428 REAR LOG SUPPORT (30″ MODELS)

11376 BURNER SUPPORT – LEFT

P200 ORIFICE FITTING

R5675 AIR SHUTTER – LP

R5676 AIR SHUTTER – NAT

R5170 PILOT, LP

R5171 PILOT, NAT

11833 PILOT SHIELD (NAT ONLY)

12437

BURNER ASSEMBLY (16″ NAT MODELS)

12348

BURNER ASSEMBLY (16″ LP MODELS)

14033 BURNER ASSEMBLY (18″ MODELS)

14035 BURNER ASSEMBLY (24″ MODELS)

14037 BURNER ASSEMBLY (30″ MODELS)

12389 CERAMIC MEDIA

R2809 DAMPER CLAMP

11788 DECORATIVE ROCK

15998 ROCKWOOL (16″ MODELS)

15999 ROCKWOOL (18″ MODELS)

15970 ROCKWOOL (24″ & 30″ MODELS)

11291

TUBING ASSEMBLY VALVE TO BURNER

VFSe

P250 ORIFICE – LP 18″

P245 ORIFICE – LP 24″

P265 ORIFICE – LP 30″

P243 ORIFICE – NAT 18″

P244 ORIFICE – NAT 24″

P211 ORIFICE – NAT 30″

R7063 PILOT REGULATOR

11308

BURNER SUPPORT RIGHT WITH VALVE BRACKET

R10562 VALVE, MAXITROL (NAT)

R13285 VALVE, MAXITROL (LP)

R10566 ELECTRONIC CONTROL

R10572 CONNECTOR, THERMOCOUPLE

14040

TUBING ASSEMBLY NAT VALVE TO REGULATOR

14041

TUBING ASSEMBLY NAT REGULATOR TO PILOT

INDEX NO.

PArT NO.

DeScrIPTION

VFSE (CONTINUED)

NS

11335

TUBING ASSEMBLY LP VALVE TO PILOT

NS R10559 BATTERY, 9-VOLT

NS R10518 FASTENER, HOOK

NS R10519 FASTENER, LOOP

NS R10573 3/8″ NPT, HEX PLUG

NS R10568 IGNITER WIRE, MAXITROL

NS R10564 REMOTE CONTROL KIT

NS R10565 REMOTE CONTROL THERMOSTAT

NS R10569 SWITCH AND WIRE ASSEMBLY

NS R10570 WIRE ASSEMBLY, THERMOCOUPLE

NS R10567 WIRE HARNESS (8 PIN)

VFSV

4

P308 ORIFICE – LP 16″

4

P210 ORIFICE – LP 18″

4

P304 ORIFICE – LP 24″

4

P265 ORIFICE – LP 30″

4

P286 ORIFICE – NAT 16″

4

P243 ORIFICE – NAT 18″

4

P211 ORIFICE – NAT 24″

4

P209 ORIFICE – NAT 30″

10

26321

BURNER SUPPORT RIGHT (16″ MODELS)

10

26291

BURNER SUPPORT RIGHT (18″,24″,& 30″ MODELS)

14 R10613 VALVE, AF1110

15 R9761 PIEZO IGNITOR

16

27017 IGNITER BRACKET

17 R10617 45° STREET ELBOW

18 R10618 REGULATOR, 4.0 W.C.

18 R10689 REGULATOR, 10.0 W.C.

19

27016 VALVE BRACKET

NS

27018

PILOT TUBE – VALVE TO PILOT (NAT & LP)

NS

R10619

REMOTE RECEIVER AND TRANSMITTER, NAT

NS

R10620

REMOTE RECEIVER AND TRANSMITTER, LP

NS R2789 WIRE, IGNITER, 12″

NS R8898 NIPPLE, 3/8 X 3/8 X 1 BLACK IRON

NS – Not Shown

Page 26

USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INjURY OR DEATH.

28092-0-1110

PArTS VIew
“VFSV” MODELS 15
16 18 17
14 19 “VFSE” MODELS
13
12 11

28092-0-1110

Page 27

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>