Mirabella 42910022 Genio Wi-Fi Portable LED Lamp Instruction Manual

Mirabella 42910022 Genio Wi-Fi Portable LED Lamp

Product Information

Specifications

• Product Name: Genio Rechargeable LED Portable Lamp
• Usage: Indoor Use Only
• Battery Charging Time: Approx. 2 hours
• Battery Run Time: Approx. 10 hours
• Supported Wi-Fi Network: 2.4GHz (5GHz not supported)

Product Usage Instructions

Install the Genio App and register the Account

For the best experience, download the Mirabella Genio app to your smartphone from the App Store or Google Play, or you can also scan the QR code below. The app icon will be displayed after a successful installation.

Charging the Light

Before using this product for the first time, please fully charge it using the supplied USB cable. Connect the USB cable to a power source and the lamp. While charging, a red light will be displayed. Once fully charged, a green light will appear. The run time of the light is approximately 10 hours.

Pairing using the Mirabella Genio App

1. Press the on/off switch and wait for the portable lamp to start blinking (approximately 2 blinks per second).
2. Ensure your mobile phone is connected to a 2.4GHz Wi-Fi network. Note: 5GHz is not supported and should be disabled on the router setting during pairing. Once the unit has been paired, 5GHz can then be re-enabled.
3. Launch the Mirabella Genio app and tap on the plus symbol + (located in the top right-hand corner).
4. Go to Smart Lighting -> Genio lighting devices.
5. Follow the app instructions to finish the pairing process. If the lamp doesn’t blink rapidly when first powered on, please try powering it off and then on/off 3 times. Alternatively, you can try powering it on and holding the Mode button.

Troubleshooting

If after the 100% countdown, you receive a timeout or device not found error, this is an indication that the app failed to communicate with the cloud services. Please ensure…

FAQ

• Q: Can I use the lamp outdoors?
• A: No, this lamp is for indoor use only.
• Q: How long does it take to fully charge the battery?
• A: It takes approximately 2 hours to charge the battery fully.
• Q: What is the run time of the light on a fully charged battery?
• A: The run time of the light is approximately 10 hours.
• Q: Can I connect the lamp to a 5GHz Wi-Fi network?
• A: No, this lamp only supports a 2.4GHz Wi-Fi network. Please ensure your mobile phone is connected to a 2.4GHz network during the pairing process.

OVER WEIW

Install the Genio App and register Account

For the best experience, download the “Mirabella Genio” app to your smartphone from the App Store or Google Play, or you can also scan the QR code below, the app icon will be displayed after installed successfully

Charging the Light

Before using this product for the first time, please fully charge it using the supplied USB cable.  It takes approx. 2 hours to fully charge the Battery. While charging the red light will be displayed, once fully charged, a Green light will appear. The run time of the light is approx. 10hrs.

Pairing using the Mirabella Genio App

1. Press the on/off switch and wait for the portable lamp to start to blink (approx. 2 blinks per second)
2. Ensure your mobile phone is connected to a 2.4GHz Wi-Fi network. (5GHz is not supported and it should be disabled on the router setting during pairing, once the unit has been paired, 5GHz can then be re-enabled).
3. Launch Mirabella Genio app, tap on plus symbol “+” (located top right hand corner)
4. Go to Smart Lighting -> Genio lighting devices
5. Follow the App instructions to finish the pairing process

Trouble Shooting

If after the 100% countdown you receive a “time out” or “device not found error” this is an indication that the app failed to communicate with the cloud services. Please ensure

1. The light is blinking rapidly (2 blinks per second)
2. Disable the 5GHz Wi-Fi signal on the router setting.

For instructions on how to disable your 5 GHz Wi-Fi network – Please contact your internet /router provider. I am using Telstra NBN, I disabled the 5Ghz and I still cannot get it to pair? Please follow the Guest Network paring instructions on https://mirabellagenio.net.au/faqs If you have done all the above, ensuring that the 5Ghz is disabled, but still failed to connect, then your modem could not be incompatible with smart device. All trademarks are used for reference purposes only. Made in China
MIRABELLA INTERNATIONAL PTY LTD 1 MIRABELLA DRIVE, TULLMARINE, VIC, AUSTRALIA 3043
TOLL FREE: 1800 636 528, www.mirabellagenio.com.au

References

• Mirabella Genio - Smart Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>