ELIVED UST-600_US1.0 Ultra Slim Tilt TV Wall Mount Installation Guide
- June 15, 2024
- ELIVED
Table of Contents
- Safety Caution
- Must Check Before Getting Started
- Product Dimensions
- Supplied Parts and Hardware
- Extra Tools You Need (Not Supplied)
- Select TV Screws and Spacers
- Attach Brackets to TV
- Assemble Wall Plate
- Hang and Secure TV to Wall Plate
- Adjustments (If necessary)
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Installation Guide INSTALLATION INSTRUCTION
UST-600_US1.0
If you have any questions, please feel free to contact our customer support before returning.
Safety Caution
Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.
-
This product is designed for use in wood stud or solid concrete wall.
– DO NOT install into drywall alone. -
The wall must be capable of supporting five times the weight of the TV and mount combined.
-
Incorrect installation may result in product damage / property damage or body injury.
We shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard
if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any
parts are missing or damaged, do not return the damaged item to your dealer;
please contact our customer service team. Never use damaged parts!
Must Check Before Getting Started
Minimum VESA Pattern (W × H): 100mm × 100mm / 4 in × 4 in
Maximum VESA Pattern (W × H): 600mm × 400mm / 24 in × 16 in WARNING
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only within the maximum weights
indicated. Use with products heavier than the maximum weights indicated may
result in failure of the mount and its accessories, causing possible damage or
injury.
Verify Your Wall Construction CAUTION:
Avoid potential personal injuries and property damage!
Drywall covering the wall must not exceed 5/8 in. (16 mm).
Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in.
(38 x 89 mm). CAUTION:
Avoid potential personal injuries and property damage!
Mount the wall plate assembly directly onto the concrete surface (no surface
covering).
CAUTION: DO NOT install into drywall alone.
Product Dimensions
Supplied Parts and Hardware
NOTE: Not all parts and hardware included will be used.
Extra Tools You Need (Not Supplied)
Select TV Screws and Spacers
1-1 Select TV Screws 1-2
Need Spacer?
Ⅰ No, just choose the screws, washers.ⅠⅠ Yes, choose the appropriate screws, washers,and
spacers for your TV.
Attach Brackets to TV
Assemble Wall Plate
4-A Attach Wall
Plate to Wall
Locate your studs.
Verify and mark the center of the stud by finding the stud edges using awl and
stud finder.
Line up the holes with your stud center line. Level the wall plate and mark
the pilot hole locations.Drill
pilot holes using a
Ф7/32 in (Ф5.5mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located. Be
sure to drill into the center of the stud.Install wall plate using lag bolts A with Socket
Wrench, NO Electrodrill.
No anchors when installed onto the wood studs.
CAUTION:
To avoid potential personal injury or property damage:
All 2 lag bolts A MUST BE firmly tightened to prevent unwanted movement of
0the wall plate assembly. Ensure the wall plate assembly is securely fastened
to the wall before continuing on to the next step.
4-B Attach Wall Plate to Wall
Drill pilot holes using a
Ф3/8 in (Ф10mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located, or
mortar between blocks.Use the
hammer to knock anchors (not included) into the concrete wall. Be sure the
anchors are seated flush with the concrete surface.
Install wall plate using lag bolts A and anchors (not included) with Socket
Wrench, NO Electrodrill.
CAUTION:
To avoid potential personal injury or property damage:
All 2 lag bolts A MUST BE firmly tightened to prevent unwanted movement of the
wall plate assembly. Ensure the wall plate assembly is securely fastened to
the wall before continuing on to the next step.
Hang and Secure TV to Wall Plate
Hang and secure TV
assembly onto the wall plate
NOTE: Please plug in the cables before hanging up the
TV.Keep pulling the straps
while hanging/taking down the TV.
If necessary Take down the TV from the MountKeep pulling the straps while hanging/taking down the
TV.
Adjustments (If necessary)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>