ELIVED YD1003 TV Wall Mount for 26 to 55 Inch TVs Instruction Manual

June 9, 2024
ELIVED

YD1003 TV Wall Mount for 26 to 55 Inch TVs

INSTALLATION INSTRUCTION

Safety Caution

Please read this instruction carefully before installation.

V9

If you do not understand these instructions or have doubts about the safety of the installation, assembly

or use of this product, please contact us.

This product is designed for use in wood stud or solid concrete wall. – DO NOT install into drywall alone.
The wall must be capable of supporting five times the weight of the TV and mount combined. Incorrect installation may result in product damage or body injury.

WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage, please contact us.
Must Check Before Getting Started

MAX:400mm/16″

<16mm(5/8″)

Min. Wood Stud Size: nominal 4″(102mm) actual 3 1/2″(89mm)

Min. 8″ (203mm)

Velcro Cable Ties ×5

Bubble Level ×1

MAX: 400mm/16″

Max: 88LBS (40KG)

Min. Wood Stud Size: nominal 2″(51mm) actual 1 1/2″(38mm)

Drywall with wood studs

Solid concrete wall

CAUTION: DO NOT install into drywall alone.

Installation Tools (Not Included)

Max: 88LBS (40KG)

Max:400x400mm/16×16″ Min:100x100mm /4×4″

If you have any questions, please feel free to contact us via Amazon.
Warm Tips You could also refer to the Video Guide about installation on our product page.

340-MU-A-DY

Step 1-1 Select TV screw diameter
Thread screws by hand into the threaded holes on the back of your TV to select which screw diameter fits your TV.
M4 M6 M8

Step 1-2 Select TV screw length

When attaching brackets to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes.

Too Short

Too Long

Correct

Correct

Wood Stud Installation Concrete Installation

7/32″ (5.5mm)

Stud Awl Wood

Finder

Drill Bit

3/8″ (10mm)
Masonry Hammer Drill Bit

2M
Band Tape

Pencil

Electrodrill

1/2″ (13mm)
Socket Screwdriver Wrench
1

Step 3-1 Select monitor plate configuration

Select the configuration A , B , C, D, or E to use based on the measurement from STEP 2

VESA Pattern (WxH)

Configuration

VESA Pattern (WxH)

Configuration

200 mm 130 mm 100 mm

100mm x 100mm

A

300mm x 200mm

C

130mm x 130mm

A

300mm x 300mm

E

200mm x 100mm

A

400mm x 200mm

C

200mm x 200mm

A

400mm x 300mm

D

200mm x 300mm

B

400mm x 400mm

E

200mm x 400mm

B

200 mm

A
for VESA hole pattern: 100x100mm, 130x130mm,200x100mm, 200x200mm.

400 mm 300 mm

C
for VESA hole pattern: 400x200mm, 300x200mm

200 mm

400 mm 300 mm

Step 2 Mesure your TV pattern
Measure and note the width and the height of the square or rectangle formed from the VESA holes pattern .
100mm 4in. 130mm 5 1/8in. 200mm 8in. 300mm 11 3/4in 340mm 13 3/4in. 400mm 16in.

8 )

B
for VESA hole pattern: 200x300mm, 200x400mm

400 mm

2M
34

D
for VESA hole pattern: 400x300mm,

300 mm

400 mm 300 mm
E for VESA hole pattern: 300x300mm, 400x400mm
4

400 mm 300 mm

200 mm 130 mm 100 mm

Hardware Included
Wall Plate

Monitor Plate

Extenders

01 x1

02 x1

3A 3B
x2 x2

Nuts

Bolts

Allen key

Hardware cWall /Product)

Lag Bolts 5/16 x 2½ in

Open-end wrench

4A

4B

4C

A

x8

x8

x1

x3

TV Screws / Washers

Philips Screws M4 x 12mm M4 x 30mm

Philips Screws M6 x 15mm M6 x 30mm

Philips Screws M8 x 25mm M8 x 45mm

Spacers L10mm

Washers Ø6mm M4-5-6

B
x1
Spacers L5mm

x4 x4

x4 x4 x4 x4

x8

x4

M-A

M-B

M-C

M-D

M-E

Step 3-2 Assemble monitor plate and extenders

x8
M-F
2

If your TV hole pattern is greater than 200x200mm, attach extenders [33A] and [33B] to monitor plate [0022] using Nut [44AA] and Bolt [4BB].

3A

B

3B

4A

3A
Step 3-3 Attach the brackets
(a) For Flat Back

3B 4B

M-A M-C M-B
Use the shorter screws No!

Top of TV

M-E Not for M8 screws

(b) For Round Back / Extra Space

M-A M-C M-B
Use the longer screws

M-E Not for M8 screws

Top of TV

No!

M-D M-F
5

Step 4A Wall plate installation (wood stud)

A-1

Locate your studs. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge-to-edge stud finder.

A-2
Bubble Level
UP
01

Position the wall plate 01 at your desired height and line up the holes with your stud center line. Level the wall plate and mark the pilot hole locations.

A-4
A UP
01

No!
Install wall plate 01 using lag bolts A with Socket Wrench, NO Electrodrill. Tighten the lag bolts A until they are pulled firmly against the wall plate 01

Step 4B Wall plate installation (concrete or brick)

B-1

Bubble Level

UP

Position the wall plate 01 at your desired height, level the wall plate and mark the pilot hole locations x3.

01

2
2

B-3

Concrete wall anchor 3pcs (NOT INCLUDED)

Ø10*61mm

Contact us to have these additional pieces shipped directly to you.

A UP

No!

01

7/32 in Ø5.5 mm
3/8in Ø 10 mm

A-3

2.75in 70 mm
Drill pilot holes using a 7/32 in. (5.5mm) diameter drill bit.

B-2

IMPORTANT: Pilot holes must be drilled to a depth
of 2 3/4 in (70 mm). Be sure to drill into the center of the stud.

Ø 10 mm 2.75in 70 mm

Install wall plate 01 using lag bolts A
with Socket Wrench, NO Electrodrill. Tighten the lag bolts A until they are pulled firmly against the wall plate 01

Concrete Wall Concrete Wall

Step 5 Lift and hang TV with brackets onto wall bracket

67 Drill pilot holes
Adjustments

78

8

Product dimensions:

Lift and hang TV assembly onto arm and wall plate.

Tilting Adjustment
-15° +5°

(Tilting)
Tilting Angle Adjustment (+5° / -15°) Loosen 2 tilting bolts, pull TV to your desired angle, then fasten tilting nuts with Allen key.

426.5mm/16.8″ 400mm/15.7″ 200mm/7.9″ 100mm/3.9″
100mm 200mm 400mm 427mm /3.9″ /7.9″ /15.7″ /16.8″

100.5mm/4″ 225mm/8.9″
101mm/4″

58mm/2.3″ 30.9mm/1.2″

Remove 2 preassembled screws and washers, save them for using to next step.

6.9mm/0.3″

4C

8.9mm/0.4″

±3°

9mm/0.4″

Secure the monitor plate to the arm and wall plate with the removed screws and washers from the previous step.

Leveling adjustment (-3°/+3°)
If needed, TV can be leveled ±3 degrees via adjusting the 2 screws with the open-end wrench.
± 3°

+5°

200mm/7.9″

200mm/7.9″

-15°

±90°

No!

206mm/8.1″

206mm/8.1″

52mm/2″

B

B

64mm/2.5″ ~479mm/18.9″

Loosen the screws

Level the TV

Tighten the screws

9410

1011

11

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals