ELIVED YD3029 Long Arm TV Mount Full Motion Wall Mount TV Bracket Instruction Manual
- June 15, 2024
- ELIVED
Table of Contents
INSTALLATION INSTRUCTION
YZ2310_US1.0
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
Safety Caution
Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.
-
This product is designed for use in wood stud or solid concrete wall.
– DO NOT install into drywall alone. -
The wall must be capable of supporting five times the weight of the TV and mount combined.
-
Incorrect installation may result in product damage / property damage or body injury.
We shall bear no responsibility for any damage or injury resulted from
incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard
if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any
parts are missing or damaged, do not return the damaged item to your dealer;
please contact our customer service team. Never use damaged parts!
Must Check Before Getting Started
Minimum VESA Pattern (W × H): 150mm × 100mm / 6 in × 4 in
Maximum VESA Pattern (W × H): 800mm × 400mm / 32 in × 16 in
WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended
for use only within the maximum weights indicated. Use with products heavier
than the maximum weights indicated may result in failure of the mount and its
accessories, causing possible damage or injury.
Verify Your Wall Construction
CAUTION:
Avoid potential personal injuries and property damage!
Drywall covering the wall must not exceed 5/8 in. (16 mm).
Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in.
(38 x 89 mm).
CAUTION:
Avoid potential personal injuries and property damage!
Mount the wall plate assembly directly onto the concrete surface (no surface
covering).
CAUTION: DO NOT install into drywall alone.
Product Dimensions
Supplied Parts and Hardware
Extra Tools You Need (Not Supplied)
Attach Brackets to TV
1-1 Select TV Screws
1-2 Need Spacer?
I, choose the appropriate screws, washers,and spacers for your TV.
1-3 ****
Do not tighten the screws excessively or tighten them by using the
Electrodrill, or your TV might be damaged.
2-A Attach Wall Plate to Wall
OPTION A: Wood Stud Installation
Locate your studs. Verify and mark the center of the stud by finding the stud edges using awl and stud finder.
Line up the holes with your stud center line. Level the mounting template and mark the pilot hole locations.
Drill pilot holes using a
Ф7/32 in (Ф5.5mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located. Be
sure to drill into the center of the stud.
Install wall plate using lag bolts A and Washers B with Socket Wrench, NO
Electrodrill. No anchors when installed onto the wood studs.
CAUTION:
To avoid potential personal injury or property damage:
All 4 lag bolts A MUST BE firmly tightened to prevent unwanted movement of the
wall plate assembly. Ensure the wall plate assembly is securely fastened to
the wall before continuing on to the next step. To prevent the TV falling
down, the tilt bolt must be on top at this step!!
2-B Attach Wall Plate to Wall
OPTION B: Solid Concrete Wall Installation
Drill pilot holes using a
Ф3/8 in (Ф10mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located, or
mortar between blocks.
Use the hammer to knock anchors (not included) into the concrete wall. Be sure the anchors are seated flush with the concrete surface.
Install wall plate using lag bolts A and Washers ,B and anchors (not included)
with Socket Wrench, NO Electrodrill.
CAUTION:
To avoid potential personal injury or property damage:
All 4 lag bolts A MUST BE firmly tightened to prevent unwanted movement of the
wall plate assembly. Ensure the wall plate assembly is securely fastened to
the wall before continuing on to the next step. To prevent the TV falling
down, the tilt bolt must be on top at this step!!
Hang and Secure TV to Wall Plate
3-1 Before hanging TV, please conduct “wall plate installation integrity test” first.
3-2 Hang and secure TV assembly onto the wall plate.
Adjustments
4-1 Leveling Adjustment
If needed, TV can be leveled ±1 degrees via adjusting the 2 nuts with the
wrench (C).
4-2 Tilt Adjustment
- Loosen the tilting nuts ×2.
- Adjust TV to your desired angle.
- Retighten the nuts to fix the intended angle.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>