Potensic ATOM SE GPS Drone User Manual
- June 15, 2024
- Potensic
Table of Contents
ATOM SE GPS Drone
User Manual
V02. 23. 12
DANGER Only suitable for ages 16+
Email: support@potensic.com
Email: support.uk@potensic.com
Email: support.de@potensic.com| Email:
support.fr@potensic.com
Email: support.it@potensic.com
Email: support.es@potensic.com| Email:
support.jp@potensic.com
Web: www.potensic.com
FB: www.facebook.com/Potensic
---|---|---
Disclaimer & Precautions
1.1 Disclaimer
Drones are products that are potentially dangerous and relatively complex to
operate. Please be sure to read the full User Manual to ensure that you
understand the basic knowledge of the drone and are familiar with the basic
functions before usage. It is recommended to use it in GPS mode in an open
outdoor area for the first time to get familiar with the operation.
Please follow the Manual’s operation instructions and precautions strictly, in
order to use the product safely and correctly.
Users aged under 16 should be accompanied by an adult while using the product.
Please keep the product out of children’s reach.
For any direct or indirect loss (including but not limited to property loss
and personal injury) due to user’s failure in following the Manual’s safety
operation, the Company disclaims any responsibility and does not provide
warranty services.
Do not dismantle any part except for propellers, or refit the product and
attach other items on it without official guidance; otherwise, user will be
responsible for any consequences arising from violations.
For any problems in usage, operation and maintenance, please feel free to
contact our local dealer or the Company.
Potensic reserves the final interpretation rights of this document and related
product documents, and is subject to change without notice. Please visit
https://www.potensic.com for the latest information.
1.2 Safety Precautions
Keep away from obstacles and crowds
Keep the product away from crowds, high-rise buildings and high-voltage
cables, and avoid using it in severe weather such as wind, rain and thunder,
in order to keep the safety of the user and the crowds, for the product may
have uncertain flying speed, status, and potential hazards.
Keep off moisture
Keep the product off moisture to avoid an anomaly or damage due to humidity of
precise electronic components and mechanical parts inside it.
Safe operation
The product may be exposed to higher risk when user feels tired or lacks of
energy and experience. Please refit or repair the product with the original
parts to keep safety. Please operate and use the product within the allowed
range and make sure to follow the local safety rules.
Keep away from high-speed revolving parts
While the product’s propellers are revolving at a high speed, keep it away
from the crowds and animals to avoid scratch or disturbance. Do not touch the
revolving propellers with hands.
Keep away from heat source
Keep the product away from heat and high-temperature exposure to avoid the
anomaly, deformation and even damage, for it is made of metal, fiber, plastic
and electronic elements.
1.3 Warning & Prompts
-
Please properly keep the package and manual which contain important information.
-
User should avoid personal and property losses when using the product.
-
Neither the Company nor our dealers bear any liability for the proper losses and personal injuries due to users.
-
Debug and install the product in strict accordance with the Manual’s steps. Keep a distance of over 1~2m from others while using the product, to avoid injury when the product crashes into people’s heads, faces, and bodies.
-
The product should be assembled by an adult. Users aged below 16 should not handle the product alone.
The battery should be charged under the supervision of an adult and by avoiding inflammables. -
Keep the product out of children’s reach to avoid eating it by mistake, for it contains small parts.
-
Do not use the product on the road or in water to avoid an accident.
-
It is forbidden to dismantle or refit the product, except for the propellers; otherwise, an anomaly may occur.
-
Please recharge the intelligent battery with a USB charger that conforms to FCC/CE standards.
-
The remote controller has a built-in 3.7V lithium battery which needs no replacement.
-
Do not short-circuit or squeeze the battery to avoid explosion.
-
Do not short-circuit, break down or throw battery in fire or place it in a hot place (in fire or near an electric heater).
-
Keep a safe distance from the propellers which are revolving at a high speed; do not use the product in crowds to avoid scratch or injury.
-
Do not use the product in places with strong magnetic field, such as near high-voltage cable, buildings that contain metals, automobiles and trains; otherwise, the product can be disturbed.
-
Please do master local laws and regulations, to avoid violation of regulations.
-
Stop using the remote controller within the radio control period and region of national departments as specified, in order to conform to the requirements for magnetic environment of aeradio.
-
Avoid low-altitude flight above water surface.
-
Keep it away from airport, airline and other no-fly zone.
Reading Tips
2.1 Symbols
| Prohibited| | Operation & use prompts
---|---|---|---
| Important| | Technical Terms and reference information
2.2 Suggestions of Use
- User is highly suggested to watch the tutorial video and Quick Operation Guide before consulting the Manual.
- Make sure to read Disclaimer & Precautions first when consulting the Manual.
2.3 Tutorial Video / Download App
Scan the QR code on the right and you can:
- Download PotensicPro App (hereinafter referred to as “the App”).
- Watch the tutorial videos.
- Access the latest User Manual.
- Learn about the frequently asked questions(FAQ)
http://newapp.depstech.com//index.php/webapp/app/index?product=Atom&language=english
2.4 Registration & Help
Make sure to register a personal account in App before the first flight, in
order to get a better use experience.
Steps of Registration
Please fill in your E-mail, and password, check the protocol, and click
“Register”. You can log in to the system after registration.
(Note: Keep the mobile phone online during registration)
Help
Thanks for purchasing the Atom SE drone. Please read the Manual carefully.
Please contact our support team at support@potensic.com if anything needs
help, when requesting an after-sales service, it is required to submit the
order ID and details of the issues.
2.5 Technical Terms
IMU| IMU (inertial measurement unit), the most important core sensor of the
drone.
---|---
TOF (Time of Flight)| TOF (time of flight), the period from transmission and
receiving of detection infrared signal, in order to determine the target
distance.
Downward Vision System| The sensor system, which lies at the bottom of the
drone and consists of camera and TOF module.
Vision Positioning| High-accuracy positioning, which is realized through
Downward Vision System.
Compass| Identify direction for geomagnetic sensor and the drone.
Barometer| Atmospheric pressure sensor, which enables the drone to determine
the altitude through atmospheric pressure.
Lock/unlock| Switch the drone motor from static status to idle running.
Idling| Once unlocked, the motor will start revolving at a fixed speed, but it
has insufficient lifting force to take off.
Auto return| The drone will return to HOME point automatically based on GPS
positioning.
EIS| Electronic Image Stabilization; the camera will detect the data of high-
frequency vibration and eliminate picture flutter through algorithm.
Drone head| Position of the drone camera.
Throttle control stick| Ascend or descend the drone.
Pitch control stick| Fly the drone to front or back.
Roll control stick| Fly the drone to left or right.
Yaw control stick| Enable self-rotation of the drone to left or right.
Overview
This chapter introduces the functional characteristics of Atom SE, as well as the component name of the drone and the remote controller.
3.1 Introduction
With foldable arms and weight below 250g, the product is portable, and easy to
use. The product is equipped with a vision positioning system, to realize
precise hovering at low altitude indoor and outdoor environment. Meanwhile,
the product is equipped with a GPS sensor to realize positioning and auto
return. With 1/3″ Sony CMOS image sensor, the product can shoot 4K/30FPS HD
video and 1.2-megapixel pictures. Atom SE uses self-developed ShakeVanish
electronic stabilization technology to make the picture clear and stable.
By using the brand new PixSync 2.0™ 2.4G digital image transmission technique,
the Atom SE remote controller can realize 4 km communication distance and 720P
HD image transmission maximally at ideal conditions. Open the pull-type and
the foldable remote controller to contain your mobile device. Connect the
remote controller and mobile device with USB data cable, to operate and set
the product through App and display HD image transmission picture. The built-
in lithium battery of the remote controller can work for approx. 2.3h
maximally.
Atom SE uses proprietary SurgeFly™ flight control technology, with a maximum
horizontal flight speed of 16m/s (52ft/s), a maximum flight time of about 31
minutes, and the ability to withstand winds of up to level 5.
Test conditions of the max. flight time: Fly at an even speed of 5m/s at 25°C
and in breezeless condition.
Test conditions of the max. transmission distance: Measured at an open and no-
interference environment, with a flight height of 120m, and without
considering the return of the drone.
Power consumption will increase considerably when the drone is returning
against the wind. If you receive a prompt of encountering strong wind from the
App, please make sure to lower the flight altitude and return in time to
ensure safety of the drone.
Pre-Flight Checklist:
- Pay attention to the local weather forecast and make sure it is suitable for flying the drone.
- Make sure the battery is fully charged.
- Make sure the firmware is updated to the latest version.
- Make sure the flight environment is open and free of interference.
- Before takeoff, make sure the battery is secured and the buckle pops out correctly, and no deformed propellers and loose screws.
- Power on the drone on open and level ground, wait for the drone to enter GPS Mode before takeoff, and pay attention to the HOME point.
3.2 Drone Diagram
1. Charging indicator
2. TYPE-C charging port
3. Battery buckle
4. SD card slot
5. Tail indicator
6. Monocular visual module
7. TOF module
8. Bottom cooling hole| 9. Power indicator
10. Power/frequency pairing button
11. Integrated single-axis gimbal camera
12. Brushless motor
13. Propeller
14. Arm
15. Antenna tripod
16. Arm shaft
---|---
3.3 Remote Controller Diagram
-
Power button
Long press it for 2s to power on/off. -
Power indicator
Indicate the power level or other status of the remote controller -
Control stick slot
One slot respectively at the left and right side, which are used to store the sticks -
TYPE-C interface
To charge the remote controller/connect mobile device -
RTH / Pause button
Long press for 1s to return to HOME point automatically Short press it to pause auto flight -
Control stick
-
Foldable double antennas
-
Installation position of mobile device
To place mobile device. -
Shoot button
Short press it to shoot one picture -
Record button
Short press it to start/stop recording -
Thumbwheel
Dial the thumbwheel horizontally to control the tilt of the gimbal.
3.4 Preparing the Drone
The product is delivered under folded status. Please unfold it as follows:
- Unfold the front arm before the rear arm.
- Unfold the propeller blades.
3.5 Preparing the Remote Controller
Installation of mobile phone and control stick
- Unfold the antenna.
- Connect your mobile phone to the USB cable.
- Insert the part of your mobile phone with the USB cable into the slot of the remote controller.
- Pull and open the remote control with both hands and fix your mobile phone stably.
- Connect the other end of the USB cable to the remote controller.
- Take out the sticks.
- Screw in both control sticks clockwise.
- Installation completed.
3.6 Charging / Startup and Shutdown
When receiving a new drone battery, it is required to charge it to wake it up,
otherwise the drone won’t start. Connect the TYPE-C charging port of the
battery and a USB charger to the AC power supply to finish a one-time charging
(USB charger is not included in the package. User can use the charger that
conforms to FCC/CE specification to charge the battery). The red indicator
will stay on during charging, and turn off automatically after charging is
done. Users can charge the battery with the Parallel Charging HUB if a fly
expansion kit is purchased. For more details, please refer to the Uer’s Manual
of Parallel Charging HUB. The Parallel Charging HUB can also charge the remote
controller. The shortest
charging period is approx. 1h 25min through the type-C charging port. Make
sure your charger supports 5V/3A output in order to achieve this charging
speed.
User is suggested to charge the battery through the Parallel Charging HUB, in
order to charge 3 batteries quickly at the same time.
It is suggested to remove the battery from the drone to charge for the sake of
safety; otherwise, the drone won’t power on if the battery is being charged in
the drone.
If the charging cable is connected while the drone is on, it will power off
automatically and the charging will continue.
The battery may become too hot after use; do not charge it until it cools
down; otherwise, charging can be rejected by the smart battery.
Charge the battery on a trimonthly basis to maintain the activity of the cell.
Please connect the original cable or any cable that supports over 3A current
to the type-C port; otherwise, it may cause charging failure or battery
damage.
Startup
Drone: Make sure the battery is inserted in the battery bin, short press
and then long press the power button until all indicators are on, and then
release the button to start up.
Remote controller : Long press the “Power” button until all indicators
are on, and then release the button to finish startup.
Shutdown
Drone: Short press and then long press the power button of the drone
until all indicators are on, and then release the button to shut down.
Remote controller: Long press the power button until all indicators are
off, and then release the button to shut down.
Drone
The product consists of a flight control system, a communication system, a
positioning system, a power system and a smart flight battery. This chapter
sets down the functions of all parts of the drone.
4.1 Positioning
Atom SE adopts Potensic’s new SurgeFly™ flight control technology, which
supports the following two positioning modes:
GPS positioning: Provide precise positioning and navigation to the drone;
support precise hovering, smart flight and auto return.
Vision positioning: It can realize high-precision positioning at a low
altitude based on the Downward Vision System. The visual positioning can be
realized without a GPS signal, so that the product can be used indoors.
How to switch: The flight control system will switch automatically
according to the environment of the drone. If both the GPS and lower visual
system fail, the flight control will be switched to attitude mode, under
which, the drone fails to realize stable hovering and the user needs to
correct the flight gesture manually through the control stick.
The difficulty of drone handling will be increased greatly in the attitude
mode; make sure to master the behaviors and operation of the drone in this
mode before using this mode; avoid flying the drone at a long distance, to
avoid risks due to failed judgment of drone gestures.
User can also switch to attitude mode in App.
In visual positioning, smart flight is not supported and flight speed will be
restricted.
The difficulty of controlling the drone will increase dramatically in ATTI
Mode so make sure to master the operation of the drone in this mode. Always
keep the drone within sight in order to avoid risks in case of failed judgment
of the drone’s attitude and direction.
4.2 Downward Vision System
The Atom SE is equipped with a downward vision system, it is located beneath
the drone. The Downward Vision System consists of a monocular camera and a TOF
module. The TOF module includes a transmitter tube and a receiver tube, it can
precisely calculate the fly height above the ground by calculating the
infrared signals transmission and receiving time.
In combination with the monocular camera, the system can help achieve high-
precision positioning at low altitudes. Detection Fileds
The Downward Vision System works best when the drone is at an altitude of 0.3
to 5 m, and its operating range is 0.3 to 10 m.
When GPS is unavailable, the Downward Vision System is enabled if the surface
has a discernable surface and sufficient light. The Downward Vision System
works best when the drone is at an altitude of 0.3 to 5 m. If the drone’s
altitude is above 5 m, the Vision System may be affected, so extra caution is
required.
How to use
The Downward Vision System has enabled automatically if the positioning
conditions are satisfied. The drone tail indicator blinks cyan twice, which
indicates the Downward Vision System is working.
Speed limit: To ensure positioning accuracy and flight safety during
visual positioning flight, the drone will actively limit its flight speed.
Visual positioning is only an auxiliary flight function, please always pay
attention to the changes in the flight environment and positioning mode, and
do not rely too much on the automatic judgment of the aircraft. Users need to
control the remote at all times and be prepared to operate the aircraft
manually at any time.
The Vision System cannot work properly in any of the following situations
- Pure-color surface.
- Surface with strong reflection, such as smooth metal surfaces.
- Transparent object surface, such as water surface and glass.
- The moving texture, such as running pets and moving vehicles.
- Scenarios with drastic change of light; For example, the drone flies to outdoor space with strong light from indoor space.
- Places with weak or strong light.
- The surface with highly repetitive texture, such as floor tile with the same texture and small size, and highly consistent strip pattern.
For the sake of safety, please check the camera and TOF transceiver tube
before the flight, and clean it with a soft cloth if there is any dirt, dust,
or water on it;
Contact Potensic Support if there is any damage to the Vision System.
4.3 Drone Status Indicator
Start-up/ Shut-down| Startup / Shutdown in progress: Green indicator is solid
on
---|---
Flight status| GPS positioning| Vision positioning| Attitude mode| Return
Indicator flashes slowly in green| Indicator flashes slowly in cyan| Indicator
flashes slowly in blue| Indicator flashes slowly in red
Warning & Error| Remote controller has no connection with the drone
(communication lost)| Low battery| Sensor error| Emergency stop of propeller
Indicator is in solid blue| Indicator flashes quickly in red| Indicator is in
solid red| Indicator repeatedly lights up shortly in red then goes off long
Upgrade & calibration| Compass calibration (horizontal)| Compass calibration
(vertical)| Frequency pairing mode| Upgrade mode
Indicator has alternative flashing between red and green| Indicator has
alternative flashing between blue and green| Indicator flashes quickly in
green| Indicator flashes quickly in blue
4.4 Smart Battery
4.4.1 Function
Atom SE smart battery is mounted with high-energy cell and advanced BMS. The
details are as follows:
Basic Parameters
Model: DSBT02A
Cell Qty.| 2 series| Battery Capacity| 2500mAh
Rated Voltage| 7.2V| Charge Completion Voltage| 8.4V
Charging Mode
| TYPE-C/
Parallel Charging HUB| Max. Charge Current| TYPE-C: 5V/3A
Parallel Charging HUB: 8V/2.2A x 3
Function
|
Description
---|---
Balance protection| Balance cell voltage automatically to guarantee battery
health.
Self-discharge protection| If the battery is fully charged and left idle, it
will slowly self-discharge to 50%-70% after 5 days to protect the battery
cells.
Overcharge protection| Charging will stop once battery is fully charged,
otherwise the battery can be damaged by overcharging.
Temperature protection| Please pay attention to your charging environment,
otherwise charging will be stopped automatically when battery temperature is
below 0°C or above 40°C.
Intelligent current limiting of charging| When charging current is too high,
the battery will restrict current automatically in order to protect the
battery.
Over-discharge protection| In non-flight status, the battery will cut off
power supply automatically to avoid over-discharge when battery is discharged
to a certain level; at this time, the battery will enter sleep status. It is
suggested to charge the battery ASAP.
Short-circuit protection| When the drone short-circuit is detected by the
battery, the power supply will be cut off automatically to protect the battery
and the drone.
Battery health monitoring| The BMS will monitor the battery health condition,
prompt battery damage in App in case of cell damage, cell voltage unbalance or
other battery errors, to remind user to replace the battery in time.
Communication function| The battery can communicate with the the drone in real
time. User can view the information in App, such as battery circulation times
and real-time electric quantity.
If the battery is not used for a long time, it needs to be charged every three
months to ensure its health.
Please store the battery in a cool, dry place where children cannot touch it.
4.4.2 Battery Installation & Removal
Installation:
Push the battery into the product’s battery bin horizontally as shown in
picture below, the battery buckle is bounced and locked when hearing “click”
sound. Removal:
Firstly, press the buckle of smart battery, hold the upper cover of battery to
pull out the battery. Once the battery is inserted, make sure the battery
buckle is bounced properly. This step is highly important and related to
flight safety.
Make sure to power off the product before removing the battery. Buckle is in
position, safeBuckle is not in
position, which may result in the battery falling during flight. 4.4.3
Charging
See 3.6 for charging method
4.4.4 View Power Level
Once the battery is inserted in the drone, short press the power button to
view the power level of smart battery, as shown in the picture below:
4.4.5 Operation Instructions of Smart Battery at High/low Temperature
When the battery temperature is <5°C, the App will prompt a low temperature
warning of the battery, and the battery needs to be preheated before flying.
When the battery temperature is >60°C, the App will prompt a high temperature
warning of the battery, and the drone will not be able to fly.
The discharge capacity will be weakened greatly and flight duration will
reduce at a low temperature, which is normal.
Avoid long-term running at a low temperature, otherwise, the battery life can
be shortened.
4.5 Propellers
There are two types of Atom SE propellers, which are designed to spin in
different directions.
Marks are used to indicate which propellers should be attached to which
motors, the two blades attached to one motor are the same.
| Propeller| Installation Instructions|
Schematic Diagram of Installation
---|---|---|---
Marked propeller| | Install the marked propeller blades on marked arm|
Unmarked propeller
| | Install the unmarked propeller blades on unmarked arm|
Use the the screwdriver from the package to mount the propellers.
Hold the motor to remove the propeller blades easier. Make sure you attach the
marked propellers to the motors of the arm with marks and the unmarked
propellers to the motors of the arm without marks. Otherwise the drone will be
unable to fly.
If a propeller is broken, remove the two propellers and screws on the
corresponding motor and discard them. Use two propellers from the same
package. DO NOT mix with propellers in other packages.
Propeller blades are sharp. Handle with care. DO NOT squeeze or bend the
propellers during transportation or storage.
Purchase the propellers separately if necessary.
Stay away from the rotating propellers and motors to avoid injuries.
Please check the propeller blades immediately if there are any jitters or
speedless in flight, and timely replace the propellers if it’s damaged or
deformed.
Make sure the motors are mounted securely and rotating smoothly. Land the
drone immediately if a motor is stuck and unable to rotate freely. Stop flying
the drone and contact support if there is any abnormal sound with the motor.
Make sure that the propellers are installed securely before each flight. Check
to make sure the screws on the propellers are tightened.
When mount or remove the propellers, do not put the screwdriver or other
foreign materials inside the motors, or the motor may be damaged.
4.6 Flight Data
Atom SE supports recording of flight data. User can view the data in App.
“Flight record” can display the basic data for each flight of user.
“Flight log” can record the detailed flight data of user. For any abnormal
circumstance in flight, user can report it in App and, if necessary, upload
the flight log to seek for assistance.
All flight data are stored in user’s mobile device. No flight data will be
acquired by the Company, except for the data uploaded by user to the cloud
platform.
4.7 Single Axis Gimbal Camera
4.7.1 Single Axis Gimbal
The Atom SE camera is mounted with a single-axis gimbal, to adjust pitch angle
freely from +20° to -90° (horizontal direction is 0°).
The angle of the gimbal can be adjusted by scrolling the left thumbwheel of
the remote controller. The gimbal will be recovered to -9°
automatically after each startup.
Avoid collision and moving the lens by force, for the gimbal contains precise
parts.
Make sure the gimbal has no foreign matters and lens is free from dirt before
takeoff.
The gimbal is connected to the drone through elastic and shock absorption
support, to eliminate camera vibration. Do not pull the gimbal by force. For
any damage of shock absorption support, please timely contact the after-sales
department for repairing.
Do not bind or paste any object on the gimbal. Otherwise, it may damage the
drone.
4.7.2 Camera
Basic Parameters
Sensor brand: SONY| Sensor size: 1/3″
Effective pixel: 12MP| Aperture: F2.2
FOV: 118°| Focus range: 3m ~ ∞
ISO range: 100~6400| Shutter range: 1/30~1/25,000s
Memory: Micro SD card| Shooting distortion: < 1% (after calibration)
Picture size: 12MP| Picture format: JPG/JPG+RAW(DNG)
Video format: MP4| Code: H.264
Video specification: 4K@30fps; 2.7K@30fps; 1080P@60/30fps
Do not touch the lens after recording for a long period of time to avoid
scald.
Do not record video when the drone is not flying; otherwise the drone will
trigger overheat protection.
The sensor will crop out the edges at 1080P/60fps, it’s simply capturing a
central section of what the full-frame sensor would capture, and FOV is about
66°.
4.7.3 Image Storage
The videos and pictures recorded by Atom SE will be stored in SD card, instead
of App or user’s album. Make sure to insert SD card prior to flight.
Otherwise, it is unable to record and shoot.
(SD card is not included in the product’s pack list!)
User can preview and download the videos and pictures (the drone and the
remote controller should be connected) in App.
SD Card Requirements
File format: FAT32, exFAT
Capacity: 4G-256G
Speed requirements: It is suggested to use SD card above U1 (UHS Speed Class
- or C10 (Class 10)
The video downloaded from App is just 720P resolution used in video transmission. Please read SD card with computer or other device in order to acquire videos of higher definition.
The recording can be terminated due to slow write-in when using the U1/C10 SD cards of certain brands.
If important data are stored in your SD card, please backup them properly.
Do not insert or unplug the SD card when the product is powered on. It may lead to data damage or loss, or even SD card damage when inserting or unplugging SD card during video recording.
Potensic does not bear responsibility for any loss due to user’s misoperation of SD card.
Remote Controller
5.1 Overview
Potensic Atom SE is equipped with the DSRC02A Remote controller, which boasts
Potensic long-range PixSync 2.0™ image transmission technology, offering a
maximum transmission range of 4km/13,123ft and 720p when displaying video from
the drone to PotensicPro on your mobile device. Easily control the drone and
camera using the onboard buttons. The detachable control sticks make the
remote controller easier to store. Thanks to the 2.4Ghz dual band antenna, in
a wide-open area with no electromagnetic interference, PixSync 2.0™ smoothly
transmits video feed at up to 720p at a max altitude of 120m.
The built-in battery has a capacity of 3000mAh and a maximum run time of 2.3
hours. There is a USB C port for device connection. The remote controller
charges the mobile device with a charging ability of 500mA@5V.
When used with different drone hardware configurations, the remote controller
will automatically select the corresponding firmware version for updating and
support the following transmission technologies enabled by the hardware
performance of the connected drone models: a. Atom SE: PixSync 2.0™ b. Atom:
PixSync 3.0™
5.2 Control Stick Mode
Mode 1 (Left Hand Throttle) Mode 2 (Right Hand Throttle) 5.3 Function
5.3.1 Function List
Charge| 1. Connect the USB Charger to the USB C charging port.
2. The battery is being charged when power indicator starts flashing.
3. Charging is completed when 4 LED indicators are solid on and data cable
can be removed.
---|---
Recharge mobile phone| When a mobile device is connected, the remote
controller automatically charges devices with a charging ability of 500mA@5V.
Indicator function| See 5.3.2
Flight control| See 5.2
Low battery prompt| When power level of the remote controller is lower than
10%, the remote controller will have a “beep” sound every second.
Auto shutdown| The product will shut down automatically if the remote
controller has no connection and operation for 20mins.
One-key return| See 7.9
Pause| If the drone is performing a Smart Flight like Circle Flight or auto
landing, press once to make the drone brake and hover in place. Press again to
cancel it and regain the control of the drone.
Emergency stop| For any emergency situtaions during the flight, press “Shoot”
and “Record” button for 2s at the same time till the remote controller beeps,
the drone will stop running and fall down.
Shoot| Short press it to shoot one picture
When camera is in video recording mode, short press it to switch to shoot mode
Record video
| Short press it to start/stop video recording
When camera is in shooting mode, shot press it to switch to video recording
mode
Gimbal Dial| Dial it to the right to increase the pitch angle (head up)
Dial it to the left to decrease the pitch angle (head down)
Remote controller frequency pairing| See 5.3.3
5.3.2 Indicator
As shown in the picture below, the remote controller is fitted with 4 white
LED indicators to indicate the power level and other status.
| Indicator is on
---|---
| Indicator is flashing
| Indicator is off
Charging indication
LED 1
| LED 2| LED 3| LED 4|
Current power level of battery
---|---|---|---|---
| | | | 0%~25%
| | | | 25%~50%
| | | | 50%~75%
| | | | 75%~99%
| | | | 99%~100%
Power indication (in use)
LED 1
| LED 2| LED 3| LED 4|
Current power level of battery
---|---|---|---|---
| | | | 0%~10%
| | | | 10%~25%
| | | | 25%~50%
| | | | 50%~75%
| | | | 75%~100%
Status indication
| LED 1| LED 2| LED 3| LED 4
---|---|---|---|---
Frequency pairing| | | |
Flashing slowly at the same time
Upgrade mode|
Turning on sequentially
Start calibration| | | |
Flashing slowly at the same time
5.3.3 Remote Controller Function
The Atom SE drone and the remote controller can be used immediately after
startup since they have passed frequency pairing before delivery. If a new
remote controller or drone is used for the first time, user must conduct
frequency pairing for them as follows prior to use:
- Power on the remote controller and connect it with the mobile phone, launch PotensicPro App, tap Settings and select “Re-pair the drone” to enter the frequency pairing interface.
- After powering on the drone, long press the“Power”button until the drone indicator flashes quickly in green; now the drone is ready for frequency pairing.
- Wait for about 7s, the remote controller beeps once to indicate frequency pairing is successful and the flight interface of the App will show realtime video transmission.
Make sure the remote controller is within 1m of the drone during frequency
pairing, and there is no 2.4G frequency interference.
If frequency pairing fails, check if there are interferences nearby, or other
drones are also in frequency pairing mode, or the remote controller is too far
away or blocked. Eliminate the problems above and try again.
Do not relocate or operate the remote controller and the drone during
frequency pairing.
5.4 Antenna Angle
Adjust the antenna angle along with the changes of drone height and distance,
to ensure the best communication status of the remote controller.
Wider communication angle is ensured at a close distance in this
mode.Keep
both antennas pointing directly towards the drone to acquire a longer
transmission distance. When the drone is right above the remote controller,
the transmission signal is weakened drastically due to poor antenna angle.
Please lower the flight altitude or fly the drone horizontally for some
distance with the antenna pointing at the drone as much as possible as shown
in the picture. Do not cross the antenna in any case Do not press the antenna
on your mobile device in any case. 5.5 Remote Controller Calibration
5.5.1 When to perform remote controller calibration
- When the drone drifts automatically in one direction without any toggling of the control sticks.
- When the drone automatically and continuously rotates in one direction.
- When the control sticks are over-sensitive or lack sensitivity.
5.5.2 Calibration Procedure
- Turn on the remote controller, and connect the mobile device, tap Settings in App, select “Remote Controller Calibration”
- Make sure the control sticks are in the middle position and do not operate it before tapping to start the calibration.
- Tap “Start Calibration”, then follow the on-screen instructions and toggle the sticks in all directions until 100% is displayed in App interface, and then maximum toggle the thumbwheel back and forth.
- When App prompts “Calibration Succeeded”, the remote controller calibration is completed.
PotensicPro App
6.1 App Homepage 6.2 Flight Interface
1.
Return button:
Tap to return to the homepage
2. Navigation prompt bar:
Display drone status and flight mode
3. Flight mode:
Video
Normal
Sport
4. Positioning mode:
GPS positioning
Vision positioning
Attitude mode, no positioning
5. GPS status:
Display GPS signal status and quantity of satellites searched
6. Signal quality of video transmission:
Display the strength of video transmission connection signal between the drone
and the remote controller
7. Power level of the smart battery: Estimated Remaining Flight Time
8. Settings
Tap to view information about Safety, Calibration, Control, Camera and About.
Safety
Switch on or off Beginner Mode: If switched on, the drone will be confined to
fly in a cylindrical space with a radius of 30 m and a height of 30 m and
restricted to fly only in Video Mode.
Set measurement system (Metric or Imperial) and speed (Video/Normal/Sport)
Set minimum return altitude and virtual fence.
Battery information: check the temperature, current, voltage and others of the
smart battery. Calibration
This sector includes compass calibration, remote controller calibration and
drone re-pairing.
Control
Remote Controller Settings: Tap to switch control stick mode (Mode 1: Left
Hand Throttle; Mode 2: Right Hand Throttle)
Camera
General Settings: Tap to set white balance, gridlines, segmental recording,
etc. Tap to check Micro-SD card capacity and format.
Other Settings: Tap to set watermarks in photos.
About
View device information, firmware information, App version, etc.
9. Shooting Information Display/Settings
Photo Mode: displays photo format, EV (exposure value) and the remaining
numbers of photos or the available capacity of the current microSD card.
Video Mode:
displays video resolution, EV (exposure value) and the remaining video
recording time or the available capacity of the current microSD
card.10. Shooting
Information Display/Settings:
to switch from shooting to video recording
to switch from video recording to shooting.
11. Shoot/Record button:
Video recording mode, tap to start video recording
Video recording in progress, tap to cancel
Shooting mode, tap to shoot picture
12. Album:
Preview or download shot videos or pictures in SD card.
13. Display flight speed and distance
Horizontal distance from the drone to HOME point
Flight speed of the drone
Relative height from the drone to HOME point
Ascent/descent speed of the drone
14. Flight Safety and Technical Tips
Users can turn on/off Flight Safety and Tips in App Settings->Safety. After
turning it on, flight-related
tips or suggestions will be displayed on the lower right side of the flight
interface.
15. Attitude Indicator/Thumbnail map
Tap the upper right corner to switch to Attitude Indicator Mode
Tap thumbnail map to switch to full-screen map
The attitude
indicator displays information of drone direction, tilt angle, remote
controller direction, HOME point and more.
The attitude indicator can show the angle and direction of the drone in real
time as follows:
Legend|
|
| |
---|---|---|---|---
Tilting direction of the drone| Tilt forward:
the horizon line tilts towards the upper half of the attitude| Tilt
backward: the horizon line tilts
towards the lower half of the attitude| Tilt to the right: the horizon
line tilts towards the right side| Tilt to the left:
the horizon line tilts towards the left side
| indicator| indicator| |
Different colors of the attitude indicator:
Legend
|
Description
---|---
| Green indicates that the drone is flying at a relatively small tilt angle, and optimal video quality can be achieved.
| Yellow indicates that the drone is flying at a relatively large tilt angle, and the video quality may be reduced.
| Red indicates that the drone is flying at a very large tilt angle. If the attitude indicator frequently turns red during flight, the drone may be encountering strong winds and the video quality can be compromised. Please fly the drone back and land it as soon as possible.
When the icons of the drone and the remote controller both turn green, it
indicates that the remote controller is facing the drone which guarantees the
optimal communication signal.
After the drone is powered on and enters GPS mode, the current GPS coordinates
will be updated as the HOME point. Pay attention to the update prompt of the
HOME point.
When the drone takes off in OPTI mode and then enters GPS mode, the HOME point
is no longer the take-off point. Pay attention to the return safety.
16. Intelligent Flight Modes
Intelligent Flight Modes include
Circle Flight,
Waypoint Flight and
Follow-Me Flight.
17. One-key takeoff, landing/return
The App will display different buttons based on drone status. Tap to initiate
one-key takeoff, landing or return.
Tap to unlock, take off and hover at a height of 1.2m
Tap to land or auto return.
18. Display important information or status of drone
Make sure to fully charge the mobile device prior to flight, because the power
of the mobile device will be consumed even if it is charged by the remote
controller.
Mobile cellular data is required when using the PotensicPro App. Please
contact your wireless carrier for data charges.
While using the App, make sure to read and master the pop-up prompts and
warning information of App to know the current status of the drone.
It is recommended to replace any outdated mobile device which may have a
negative impact on user experience of App and lead to potential dangers. For
any poor user experience and safety problems due to the use of an outdated
mobile device, Potensic does not bear any liability.
Flight
This chapter introduces safe flight practices and requirements.
7.1 Requirements of Flight Environment
- Do not use the product in severe weather, such as gale, rain, snow and fog.
- Only fly in open areas. Tall structures and large metal structures may affect the accuracy of the onboard compass and GPS system and result in positioning failure. It is recommended to keep the drone at least 5m away from structures.
- Control the product within your sight and keep away from the obstacles and crowds.
- Do not use the product in places with high-voltage power lines, telecommunication base station or launching tower, to avoid interference of the remote controller.
- Please use the product with caution when altitude is over 3,000m for the flight performance can be affected when the performance of drone battery and power system is weakened due to environment factor.
7.2 Precautions of Flight
-
Check if the remote controller, intelligent flight battery and mobile device are fully recharged.
-
Check if the drone is intact and propellers are installed correctly.
-
Check if the camera is working normally after power-on.
-
Check if App is running normally.
-
Check if SD card is inserted and make sure camera is clean.
6. Make sure the drone takes off on flat and hard surface, instead of sandstone or bush; the drone may fail to be unlocked if it has major vibration. -
Please be careful when the done takes off on surface of moving objects, such as running vehicle and ship.
-
GPS positioning and waypoint flight will be disabled in the south and north polar.
-
Do not use the product in extreme cold or hot place to avoid hazards.
7.3 Connection
Please follow the steps below:
- Please finish the steps in “3.5 Preparing the Remote Controller” and turn on the remote control.
- Please finish the steps in “3.4 Preparing the drone” and turn on the remote control.
- Launch App to view the connection status. Connection is finished when it shows .
- Tap to enter the flight interface.
It is advised to tap and follow the animated guide to operate for first-time users.
7.4 Flight Mode
Atom SE has three flight modes-Video/Normal/Sport, which can be switched via
the App.
Video Mode
Ascent speed: 2m/s, descent speed: 1.5m/s, flight speed: 6m/s
The system will enter beginner mode by default when using the drone for the
first time, and the flight mode will be limited at beginner mode.
Normal Mode
Ascent speed: 4m/s, descent speed: 3m/s, flight speed: 10m/s
The beginner mode can be quit after the flight operation is mastered, and the
normal mode will be entered by default. This is the common mode.
Sport Mode
Ascent speed: 5m/s, descent speed: 4m/s, flight speed: 16m/s
Video mode is recommended in aerial photography. Sport mode is recommended if
you would like to get a speedy flight experience. Please pay more attention in
Sport Mode flights as the the responsiveness of the drone significantly
increases in Sport mode.
The maximum speed and braking distance of the drone significantly increase in
Sport Mode. A minimum braking distance of 30 m (100 ft) is required in
windless conditions to ensure safety.
7.5 Compass Calibration
7.5.1 Scenarios Requiring Compass Calibration
- Compass calibration is required for first time using.
- Flying at a location further than 31 miles (50 km) away from the location the drone was last flown.
DO NOT calibrate the compass in locations where magnetic interference may
occur such as close to magnetite deposits or large metallic structures such as
metal mines, steel reinforced basements, bridges, cars, or scaffolding.
DO NOT carry objects that contain ferromagnetic materials such as mobile
phones near the drone during calibration.
Make sure the drone is at least 1m above the ground during the calibration.
It is not necessary to calibrate the compass when flying indoors.
7.5.2 Calibration Procedure
Choose an open area to carry out the following procedure.
- When calibration is required, the App will pop up the calibration interface automatically, just tap “Start calibration”, and the tail indicator will alternatively flash in red and green.
- Hold the drone horizontally and rotate it 360° till the app shows vertical calibration, and the tail indicator will alternatively flash blue and green.
- Hold the drone vertically and rotate it 360° around a vertical axis till the App prompts the calibration completed.
You can also trigger compass calibration manually in the App: Settings-
Calibration-Compass Calibration. When you get the prompt
“Calibration failed” in the App repeatedly, change the location and try the
calibration procedure again.
Do not calibrate compass while arms are folded.
7.6 Beginner Mode
The drone is automatically set to Beginner Mode for first-time use. In
beginner mode:
- The flight distance and height will be restricted at 0~30m
- The speed level will be restricted at Video mode
- The beginners are suggested to learn and master the drone in beginner mode
7.7 Takeoff/Landing/Hovering
7.7.1 Manual Takeoff/Landing
Takeoff
Step 1: Start the motors
Use a combination stick command to start the motors. Push both sticks to the
bottom inner or outer corner depending on your control stick mode to start the
motors. Release both sticks simultaneously once the motors are
spinning. Step 2: Push throttle control stick to take off
Push the throttle control stick upwards gently as shown in the picture,
release the control stick when the drone leaves ground and it will keep
hovering. Landing
Pull the throttle control stick until the drone lands on ground. Release the
throttle control stick when the motors are no longer spinning.
Take off from stable and level surface, do not take off from or land on the
palm or by hand.
It is not suggested to take off at low battery, for it may affect the battery
service life. Please handle it with caution and undertake the corresponding
consequences if forced takeoff is required.
When the drone is not in a level and stationary condition, stay at least 5 m
away from the drone, and push both sticks to the bottom inner corner for 2
seconds to forcibly unlock the motors.
Keep the distance over 0.5m between the drone and ground, for it may fail to
enter good hovering status due to air flow when it is close to the ground.
If the drone fails to be locked after landing due to anomaly, pull down the
throttle control stick to the limit position for 3s and the drone will be
locked by force.
7.7.2 One-key Takeoff / Landing
One-key takeoff
Tap one-key takeoff button in App, then swipe right in the pop-up window to
start the drone automatically then ascend to the height of 1.2m and maintain
hovering. One-key
landing
Tap one-key landing button in App, then swipe left in the pop-up window to
land the drone, or swipe right to start returning.
7.8 Smart Flight
7.8.1 Circle Flight
Description| Start circle flight, the drone will fly forwards by taking the
current position as circle center until it reaches the starting point of
circle flight; When user tap in App, the drone will fly around the circle at a
set speed and direction.
---|---
Adjustable parameter| User can set the radius,speed and direction of the
Circle Flight in Circle Flight Setting.
How to start| When GPS signal is normal and flight height is ≥5m, tap and
select in App.
How to exit| 1. Tap on the left to exit Circle Flight.
2. Move a control stick to stop Circle Flight. The drone will hover in place.
3. Short press the RTH/Pause button on the remote controller to stop Circle
Flight. The drone will hover in place.
When circle flight is enabled, the drone will ascend to 5m automatically if
its height is less than 5m.
Make sure there’s no obstacle in the radius of circle flight and use the
product with caution, for the drone does not support obstacle avoidance
function.
7.8.2 Follow Me Flight
Description| Once follow me flight is enabled, the drone will follow User’s
mobile device at the current distance; The flight height and yaw can be
adjusted during follow me flight.
---|---
How to start| When GPS signal is strong and horizontal flight distance is
5-50m, tap and select in App.
How to exit| 1. Tap on the left to exit Follow Me Flight.
2. Move a control stick to stop Follow Me Flight. The drone will hover in
place.
3. Short press the RTH/Pause button on the remote controller to stop Follow
Me Flight. The drone will hover in place.
When follow me flight is enabled, the drone will ascend to 5m automatically if
its height is less than 5m.
The follow accuracy depends on the quality of the drone GPS signal and
positioning accuracy of user’s mobile device.
The follow me flight depends on the positioning of user’s mobile device. The
positioning authority of App is required, or this function is disabled.
7.8.3 Waypoint Flight
Description| When waypoint flight function is enabled, User can freely set 1
or multiple waypoint coordinates in App map, and the drone will fly over the
corresponding coordinates according to the sequence of set waypoint
coordinates.
---|---
How to start| When GPS signal is strong, tap in App and select to enter
Waypoint Flight. Tap in the map to pin multiple waypoints, after that tap to
start Waypoint Flight.
User can set 2-30 waypoints; The figure in waypoint icon indicates the flight
sequence. Meanwhile, User can delete certain waypoints, save current Waypoint
Flight route data, or choose from the saved waypoint flights route
data.
How to exit| 1. Tap on the left to exit Waypoint Flight.
2. Move a control stick(Except the throttle stick) to stop Waypoint Flight.
The drone will hover in place.
3. Short press the RTH/Pause button on the remote controller to stop Waypoint
Flight. The drone will hover in place.
During the waypoint flight, you can adjust the flight altitude by moving the
throttle stick.
During the waypoint flight, once reaches the virtual fence, the drone will
exit the waypoint flight and hover in place.
7.9 Return(RTH)
The return consists of three steps, as follows:
- Ascent: The drone ascends to the set return altitude (this step is skipped if the drone’s altitude is already higher than the return altitude).
- Level flight: The drone maintains a straight flight at the set altitude towards the home point.
- Landing: Once it reaches the home point, the drone will automatically land and stop its propellers.
Return to Home (RTH) The drone must be in GPS mode
How to RTH
One key RTH: Press and hold the RTH button on the remote controller for 1s or
tap in App to pop up the menu, then swipe right to start the return (see
7.7.2).
Auto RTH: When either the drone battery level is low, the signal between the
drone and the remote controller is lost or the drone is experiencing other
abnormalities, Auto RTH will be triggered.
How to exit the RTH
Method 1: Tap on the left of App to exit RTH.
Method 2: Briefly press the return button on the remote controller to exit
RTH.
RTH Requirements
The drone must take off in GPS mode and successfully record the HOME point.
If the drone takes off in OPTI mode and switches to GPS mode mid-flight, it
will not be able to return to the takeoff point.
Please pay attention to the location of the HOME point on the map and the
prompts in PotensicPro App.
To ensure the safety of return flight, please set the appropriate return
altitude in the app according to the flight environment.
During the return course, users can still adjust the flight altitude by
adjusting the throttle.
The drone will return when it is within 20m of the HOME point, and the return
height will be 5m.
Please pay attention to safety.
Tall buildings or obstacles can block the transmission signal and cause signal
loss. Do not fly behind buildings beyond the return height, otherwise the
drone will collide with obstacles and crash during the return. If the drone
enters ATTI mode due to GPS failure or GPS signal interference, it will not be
able to return. During the return process, strong headwinds may be
encountered. Lowering the flight altitude appropriately can help reduce power
consumption. If the power is insufficient, the drone will perform a forced
landing in place. Please pay attention to the prompts in PotensicPro App. Do
not initiate the return when there are obstacles overhead, such as tall trees,
otherwise the drone may crash during the climb.
Please pay attention to return safety, because the drone does not support
obstacle avoidance and may crash when colliding with obstacles during the
return course.
For any GPS signal anomaly in communication loss return, the drone will
maintain hovering at ATTI mode, until GPS signal is strong enough and the
return will resume.
7.10 Emergency Stop
See 5.3.1 Emergency stop for the detailed operation method.
Emerency stop function is designed for preventing injuring pedestrians or
damaging the valuables by propeller blades in case of drone failure. Please
use it with caution, because stopping the motors mid-flight will cause the
drone to crash.
Appendix
8.1 Specification & Parameters
Drone
Model: DSDR04B
Takeoff Weight: < 249g (the takeoff weight includes battery and propeller
blades)
Folded Size: 88x143x58mm
Unfolded Size (propeller blades included): 300x242x58mm
Unfolded Size (propeller blades excluded): 210x152x58mm
Diagonal Distance: 219mm
Max Speed (Sport Mode): Ascent speed: 5m/s;
Descent speed: 4m/s; Flight speed: 16m/s
Max Wind Speed Resistance: 38km/h (Level 5)
Operating Temperature: 0°C~40°C
GNSS: GPS+GLONASS+Galileo+BeiDou
Operating Frequency: 2.400~2.4835GHz
Transmission Power: 2.4GHz: < 24dBm
Hovering Accuracy Range: Vertical: ±0.1m (with Vision
Positioning), ±0.5m (with GPS Positioning)
Horizontal Flight: ±0.3m (with Vision Positioning), ±1.5m (with GPS
Positioning)
Extra Payload: Not supported
Max hovering time: 28 mins (indoor hovering)
Downward Vision System
Hovering range: 0.3~5m(ideal environment); Available at 0.3~10m.
Unavailable scenarios of vision positioning:
- Pure-color surface
- Surface with strong reflection, such as smooth metal surface
- Transparent object surface, such as water surface and glass
- Moving texture, such as running pets
- Scenarios with drastic change of light; for example, the drone flies to outdoor space with strong light from indoor space
- The places with weak or strong light
- The surface with repeating identical patterns or textures, such as floor tile with the same texture and size
- The surface with highly consistent strip pattern
Camera
Lens Tilt Range: +20°~-90°
CMOS: 1/3″
Effective Pixel: 12MP
ISO Range: 100~6400
Electronic Shutter Speed: 1/30s~1/25000s
FOV: 118°
Aperture: F2.2
Photo Resolution: 4608*2592
Image Format: JPG/JPG+RAW(DNG)
Video Resolution: 4K@30fps; 2.7K@30fps; 1080P@60fps; 1080P@30fps;
Video Format: MP4 (H.264)
Max Video Bitrate: 40Mbps
Supported File System: FAT 32, exFAT
Type Of Supported Storage Card: Micro SD card; 4~256GB
SD card transmission speed ≥class10 or U1 standard
Remote Controller
Model: DSRC02A
Operation Frequency: 2.402~2.483GHz
Max Transmission Distance (unobstructed, free of interference): 4km
Operating Temperature: 0°C~40°C
Battery: 3000mAh, lithium battery, 1S
Transmitter Power (EIRP): 2.4GHz: ≤20dBm
Charging Interface: TYPE-C
Charging Specification: 5V/1A
Video Transmission System: PixSync 2.0™
Image Transmission Quality: 720P
Latency (depending on environment and mobile device): 200ms
Supported Mobile Device Size: Length: 170mm, Width: 100mm, Thickness:
6.5mm~8.5mm
Smart Flight Battery
Model: DSBT02A
Capacity: 2500mAh
Voltage: 7.2V
Battery Type: Li-ion 2S
Energy: 18Wh
Battery Weight: 103g
Working Temperature: 0°C~40°C
WARNING
DANGER
Only suitable for ages 16+
Warning: The product should only be used by adults and children over 16
years. Adult supervision is required for children under 16 years.
WARNING
NOT SUITABLE FOR CHILDREN UNDER 3 YEARS DUE TO SMALL PARTS
Tested according to international standards
WARNING
CHOKING HAZARD -small parts. Not for children under 3 years.
Drone FCC ID: 2AYUO-DSDR04B
Remote controller FCC ID: 2AYUO-DSRC02A
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
Manufacturer: Shenzhen Deepsea Excellence Technology Co., Ltd.
Address: 5th Floor, Building 7, Hongfa High-tech Park, Keji 4th
Road, Shiyan Street, Baoan District, Shenzhen
EC REP: E-CrossStu GmbH. Mainzer Landstr.69,60329 Frankfurt am Main
UK REP: SUQ CO., LTD. Unit G1, Capital House 61 Amhurst Road, London,
United Kingdom, E8 1LL
MADE IN CHINA
Documents / Resources
|
Potensic ATOM SE GPS
Drone
[pdf] User Manual
ATOM SE GPS Drone, ATOM SE, GPS Drone, Drone
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>