iCT H6732A-R Multi Function ToolBox Installation Guide

iCT H6732A-R Multi Function ToolBox

Introduction

Overview

• MTB(Multi-function ToolBox) is a total solution for ICT product maintenance. The portable programmer- MTB, presents data in a large LCM making product maintenance easily and fast. MTB is high convenience that could store several firmware at the same time.
• Powerful multi-functions include programmer, changer operation, lrDA download and sensor calibration.
• The all-in-one design meets all requirements form the market.

Feature

• Multi-function: Firmware download, Coin Changer operational setting and sensor calibration.
• Support Coin Changer operational settings, built-in 9 options of operation parameter, effective update function and read audit data
• High convenience: storage of several firmware at one time.
• Built-in memory and Micro-SD Card slot for large data storage.
• One multi-purpose cable for different ICT products.
• Chargeable battery and power-saving design.
• Large screen to show information.
• Friendly user interface.
• Easy to carry.

Specification

Power Consumption

• Standby 3.7V, 350 mA, 1.30W
• Operation 3.7V, 370 mA, 1.40W
• Maximum 3.7V, 2 A, 7.40W

Operation environment

• Operation Temperature – 5~50°C
• Storage Temperature – 20~70°C
• Humidity 85% (no condensation)
• Battery in charge Temperature 0~45°C
• Weight Approx. 288.5g

Dimension

Components

The reverse side

Installation

Harnesses Application

How to charge battery

Battery Capacity

• Li-ion battery: 2100 mAh

When battery low, Status LED displays blink red as well LCM displays low battery. Please charge MTB immediately.

Charge LED indicator

Charging procedure

1. Charged by PC
   • Use WEL-RHP57 to connect MTB and PC.
2. Charged by Adapter
   • It could be charged by an external adapter as well. The specification of adapter should be DC 5V, 500mA or above.

Battery Notice

• MTB’s battery should be charged at least once every six months in order to extend battery life.
• Working temperature while battery is charging: 0-450C
• Do not use MTB while battery is charging 5V DC charging voltage.
• Continues working time: up to 6 hours Charging time: 4 hours (capacity

Getting started (SWI OFF)

• Step 1. Press the ON/ OFF button to wake up MTB and then the Status LED turns on.
• Step 2. Press” ” “ ” to switch pages of the Main menu.

step 3. Choose one function that you need. Please refer to Chapters 3-7 for more function detail
Changer Operate: Set up Coin Changer operation contents

• Download FW: Download ICT products’ firmware as well as IrDADownload.
• BA Calibration: Calibration devices’ sensor.
• Auto-sleep: Set MTB interval time to turn sleep mode.(5 or 10 minutes)
• Battery & RTC: Check the remaining battery capacity as well as set RTC (date & time)
• Delete File: Deleted program files, SD Card
• Language: Select Country Language.
• Device Info: Read machine program version

Device Setting Passive mode.

Coin Changer operation setting

Connection

• step 1. Use WEL-RSBII to connect MTB and Coin Changer.
• Step 2. Press “Changer operate” on the page of Main menu.

Parameter into Coin changer Select Parameter

• File changer: The parameters set Changer.
• Changer = >File: The parameters stored Changer.

Read coin changer’s audit data(EVA DTS)

• Step 1
  • Select “Read Audit Data”.
• step 2.
  • Select transmission.
• Step 3.
  • Choose read-only or read Clear.

Download firmware for ICT products

Connection
Use WEL-RSBII to connect MTB and ICT products (BAICA etc.. )

Use WEL-RHP57 to connect MTB and XBA.
Please refer to 6-3 Steps for XBA download.

Instruction

• Step 1. Press “Download FW” on pages of Main menu.
• step 2. Select one Model Name to start download.

Steps for XBA download and DIP switches setting

• Step I
  • Use WEL-RHP57 to connect MTB and XBA. Press “Download FW” on pages of Main menu.
• step 2.
  • Select “BA” and then press “XBA”.
• step 3.
  • Press “Enter” to start downloading. Press “Back” to return the prior page.
• Step 4.
  • Press “Outside Dips” to set up XBA outside dips.
  • Press “Inside Dips” to set up XBA inside dips. If no necessary to set up XBA dip switches, please press “Enter” to download firmware directly.
• step 5.
  • After entering “Outside Dips” or “Inside Dips”, please press any dips that you want to revise. (ON or OFF)
  • Press “V ” to set up NO.5-NO.8 dips
  • Press “Back” to return the prior page.
• Step 6.
  • Press “Enter” to start download.
• step 7.
  • Press “YES” to save dip setting into XBA.
  • Press “NO” not to save dip setting into XBA.
• Step 8.
  • Download successfully and press”Confirm” back to prior page.

Download fail shown as below:

Sensor Calibration

Connection Use WEL-RSBII to connect MTB and ICT products(BA/CA etc.. )

Use WEL-RHP57 to connect MTB and XBA.

Instruction

• Step 1. Press “BA Calibration” on pages of Main menu.
• step 2. MTB detect device’s model name and firmware information.

MTB couldn’t support sensor calibration for some products that might show as below:

• Step 3. Please insert calibration card into device. Sensor calibration is successful as well resets device auto matically. Sensor calibration is fail.
• Step4. Press “Confirm” to return the prior page.

Battery Capacity

Battery Capacity & RTC (Battery & RTC)

• Step 1.
  • Press “Battery & RTC” on Main menu.
• step 2.
  • Press “Set” to set RTC date and time.
• step 3.
  • Press “9” to shift configured digit. ” + “,” ” to plus/minus number.
  • Press “Save” to save setting.

Connect to Device’s PC tool

• Step 1. Turn SWI to ON status and press “Reset”.
• Step 2. Please install USB Driver.
• Step 3. Connect device, MTB and PC. (Use WEL-RHP57 cable to connect MTB and PC)
• Step 4. Open the device’s tool and select visual comport.
• Step 5. Download the device’s firmware.
  • Press “COMI” and “PROGRAM” to download the device’s firmware.
  • If the PC tool shows a download fail message, please press “COM2” & “PROGRAM” and try it again.
• Step 6. Reset device
  • Press ” * COMI” and “RESET”. If the device doesn’t reset, please press “COM2” & “RESET” and try it again.
• Step 7. Turn SWI to OFF status and press “Reset” to back the Main Menu.

Download MTB’s firmware by pen driver

• Step 1. Please turn off MTB first.

  • Press “Confirm”.

• step 2.

  • Plug in Pen drive. MTB’s firmware in pen driver.
  • Keep pressing the button “E”, then press the “ON-OFF” button at the same time.
  • Press “YES” to download MTB’s firmware.

Troubleshooting

CONTACT

• International Currency Technologies Corporation
• No.28, Ln. 15, Sec. 6, Minquan E. Rd., Neihu Dist., Taipei City 114, Taiwan
• sales@ictgroup.com.tw. (For Sales)
• fae@ictgroup.com. tw (For Customer Service)
• Website: www.ictgroup.com.tw.
• 02016 International Currency Technologies Corporation v.2.o
• Part Number: H6732A-R

Use of Materials Limitations

• International Currency Technologies Corporation (ICT) all rights reserved.
• All materials contained are the copyrighted property of ICT.
• All trademarks, service marks, and trade names are proprietary to ICT.
• ICT reserves the right at all times to disclose or modify any information as
• ICT deems necessary to satisfy any applicable law, regulation, legal process, or governmental request, or to edit, refuse to post, or to remove any information or materials, in whole or in part, at ICT’s sole discretion.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>