Furniture of America Zinnia Tall Night Stand with Charging Station Installation Guide
- June 15, 2024
- Furniture of America
Table of Contents
ASSEMBLY INSTRUCTIONS 
VERSION # 23-03-31
Zinnia Tall Night Stand with Charging Station
TOOLS REQUIRED
Phillips Screwdriver (Not Included)
2 – People Recommended
ASSEMBLY RATING The Assembly Rating is a 5-point system showing the level of effort needed to assemble a specific product.
CHECK BEFORE STARTING
Are you missing anything?
Double-check all parts, hardware and accessories listed are all acccounted
for.
Should we send any replacements?
Are there any irregularities or flaws in the parts? We can send
replacements!
Check out our Quick Tips!
We recommend reviewing the pre-assembly handouts. Even experts need a
refresher now and then!
Prep Time!
Please review the assembly instructions and all diagrams prior to assembling.
PRE ASSEMBLY INTRODUCTION
We understand building ready-to-assemble furniture can be a challenging
experience for some. To help avoid confusion, we have provided some helpful
tips that may speed up the process. 
Teamwork
ALWAYS have at least two people to help with transporting and assembling the
product to avoid potential injury and/or damage. 
Suitable Location
Assembling near the area of the intended location is highly recommended.
Sufficient
Space
Make sure you have enough space to move around during the assembly.
Avoid Scratches
Use cardboard, blankets or a carpeted area while assembling furniture to
prevent to prevent scratches and damages. 
Flat Surface
Make sure the furniture rests on a flat and level surface with each leg evenly
touching the floor.
ASSEMBLY AND CARE ADVICE
FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE.
Position each part correctly and insert screws or bolts into their respective
holes. Use the appropriate hand tools or power tools for assembly.
Select steps, such as tightening screws and/or bolts, may require hand tools
to avoid causing damage during assembly. Turn clockwise to tighten and only
tighten when step is completed or when instructed to do so. Save the
instructions and store any supplied tools for later maintenance. After two
weeks, check and tighten any loose hardware and repeat again every six months
thereafter.
IT IS THE USER’S RESPONSIBILITY TO MAINTAIN THE FURNITURE. THE HARDWARE MAY LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE SERIOUS INJURY.
NIGHTSTAND
- Please keep instructions for future reference.
- Check the quantity and irregularity of parts and hardware before you start.
PARTS
HARDWARE
- For safety, please secure unit onto wall by using wall mounting tools provided. Refer to page 7 on wall mounting guide.
ASSEMBLY COMPLETED
Please ensure the furniture rests on an even and flat surface. If the product
wobbles or feels loose, double-check all bolts and/or screws are properly
tightened and secured.
Keep this handy!
Please retain this instruction manual and any order-related information for
future reference
Lift, don’t drag!
To avoid damage to product please always LIFT the product when transporting of
adjusting the placement.
Wall Mounting and Fixing
EXPANSION WALL ANCHOR
Our provided expansion wall anchors are only suitable for masonry walls, such
as drywall, plaster or concrete, and are best for holding lightweight items or
for anti-tip prevention. If you are unsure of the correct wall anchor to use
with the product, please request professional guidance. Liability for product
damage or failure due to using the incorrect anchors will fall on the
installer. 
CHECK BEFORE PROCEEDING
Prior to drilling or hammering, please check for wires or pipes. We recommend
using a stud finder to locate a stud, which will offer more appropriate
resistance and hold more weight.
QUICK TIPS
- If unsure of the proper size, always choose a larger screw and wall anchor.
- Match the drill bit to the wall anchor and hole size.
- Only drill horizontally. Do not force the drill or enlarge the hole for the wall anchor.
- Take extra care when drilling into high walls or ceramic tiles. Wall anchors should be a tight fit for the hole. Never use wall anchors in ceilings.
MAINTENANCE
We recommend a yearly check to see if the wall anchor or screw has loosened. If so, please remove the existing wall anchor and screw, and use a new anchor.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>